Jump to content

ALC88x 10.4.8 Kext

skippyretard

By skippyretard,
in Archive

 Share
483 posts in this topic

Recommended Posts

ganxiao
ganxiao
Posted
Posted

would anyone help?

i have a mitac 8258d laptop with c2d,945pm.ich7,mobility x1600,alc 883

i installed every driver i found,ALC883Audio.pkg ,AppleHDAPatcher,etc

all driver seems work,i can see input output device in audio panel

but internal speaker not work,i can hear a very very low voice only though a headphone set

pathmap from applehdapatcher as belows

back mic: 9 34 24

line in: 8 35 26

speaker: 20 12 2

headphone:27 38 37

spdif out: 30 6

Link to comment
Share on other sites
nils82
nils82
Posted
Posted

Hi All,

 

I have a big issue with AC'97(862) there is sound but no audio input i cant use mic or headphones.

 

I tried everything listed in the forum nothing worked for my laptop.

 

Specs:

Toshiba Pentium dual core

Nvidia Go7300 (works but unknown)

Realtek ALC862 (pain in the butt) :)

Tiger 10.4.10

Atheros Wi-Fi (works)

 

Thanks if anyone can Help

Link to comment
Share on other sites
retromacg3
retromacg3
Posted
Posted

Thanks Skippy!

 

Output works for me, on my new "just for fun" rig, seems like the other channels are there too.

 

Ga-945GCMX-S2 mobo

JaS 10.4.8 (will try it with 4.9 update, and post back)

Core Duo 2.x mhz, 2gb ram, SATA 250gb

Nvidia PCIe 7600GS 256mb

 

Need to get network working, will post on that later if it goes good.

 

Here are more detailed board specs,

  • Mfr Part Number: GA-945GCMX-S2
  • CPU: Socket 775 Support Intel Core 2 Extreme Dual-Core/ Core 2 Duo/ Pentium D/ Pentium 4/ Celeron D Processor; FSB 1066/800/533 MHz
  • Chipset: Intel 945GC & ICH7
  • Memory: 2x 240pin DDR2-667/533 DIMMs, Dual Channel, Max Capacity 2GB
  • Slots: 1x PCI-Express x16 Slot; 1x PCI-Express x4 Slot; 2x PCI Slots
  • IDE/SATA: 1x ATA-100 Channel; 4x SATA2 Ports
  • Audio: Realtek ALC888 Audio CODEC
  • Video: Intel GMA 950 Graphics Controller
  • LAN: Realtek 8110SC Gigabit Ethernet Controller
  • Ports: 8x USB 2.0 Ports (4 rear, 4 by header); 2x PS/2 Ports; 2x Serial Ports (1 rear, 1 by header); 1x Parallel Port; 1x VGA Port; 1x RJ45 Port; Audio I/O Jacks
  • Power Connector: 1x 24pin Main Power; 1x 4pin CPU Power
  • Form Factor: Micro ATX, 22 x 24.4 cm

EDIT: Works with the 10.4.9 update as well

Link to comment
Share on other sites
ImP
ImP
Posted
Posted

i uses the first one for my realtek ALC880 sound on my ASUS A6Q00VC (A6000 series) laptop

 

speakers work, if i put my headphones in all goes silent, no line in, no microphone.

 

 

 

 

 

on account of my speakers working, thx a million! :blink:

Link to comment
Share on other sites
pavn
pavn
Posted
Posted

 

 

I have mainboard: GA-P35C-DS3R, Intel Core 2 Duo E6750, 2GB DDRII 800, WD5000AAKS, DVD GSA-LG 4163B, nvidia 8500.

 

Installed OSX 10.4.6 directly to HD using vmware and sucessfully booted natively.

 

Installed RealtekR1000 from: https://sourceforge.net/projects/realtekr1000/ (http://forum.insanelymac.com/index.php?showtopic=29436&st=0&gopid=203604entry203604)

- got working LAN.

 

I tried AzaliaAudio.pkg.zip from: http://forum.insanelymac.com/index.php?sho...mp;#entry259784 .

 

Did not helped me.

 

I tried also alc889a.zip from: http://rapidshare.com/files/51585161/alc889a.zip.html (using this guide: http://forum.insanelymac.com/index.php?sho...t=#entry457698)

- OS did not booted - some bug was reported by OS.

 

My bios version is: F4i.

And I have Azalia codec enabled in setup.

Link to comment
Share on other sites
pavn
pavn
Posted
Posted

I tried AzaliaAudio.pkg.zip from: http://forum.insanelymac.com/index.php?sho...mp;&do=findComment&comment=259784 .

 

Did not helped me.

 

I tried also alc889a.zip from: http://rapidshare.com/files/51585161/alc889a.zip.html (using this guide: http://forum.insanelymac.com/index.php?sho...t=&do=findComment&comment=457698)

- OS did not booted - some bug was reported by OS.

 

Mainboard: GA-P35C-DS3R, Intel Core 2 Duo E6750, 2GB DDRII 800, WD5000AAKS, DVD GSA-LG 4163B, nvidia 8500.

 

Installed OSX 10.4.6 directly to HD using vmware and sucessfully booted natively.

 

Installed RealtekR1000 from: https://sourceforge.net/projects/realtekr1000/ (http://forum.insanelymac.com/index.php?showtopic=29436&st=0&gopid=203604entry203604)

- got working LAN.

 

My bios version is: F4i.

And I have Azalia codec enabled in setup.

Link to comment
Share on other sites
charlienail
charlienail
Posted
Posted

hey everyone i have

GB P35-S3L ICH9

ALC 888

Tried ALC888Audio.pkg but no luck.

 

someone named emzo has already figured it out luckily and left me with this little tid bit of info

 

 

 

Dev id's are:

8086 293e - controller

10ec 0888 - audio

emzo

Sep 2 2007, 02:05 PM

I managed to get audio working, by adding my dev ID to the kexts.

Mic in works

Line In works

Audio output:

In output i have 4 Line out devices.I cannot get sound played via all 7.1 speakers, i can only hear from each 2 speakers.

 

i realise i have to modify applehda.kext and alcinject.kext with those devids. how do i do that? maybe someone could help me out. i can get the codec dump from linux if needed. let's add gigabyte p35 ds3l to the list of supported alc888 boards, it was reccomended by arstechnica as a good p35 board and everything else works including sata and pata controllers and ethernet. the sound obviously works too, just gotta get the right device ids into the kext. i would do it myself but i'm not sure where to start...

 

thanks!!

Link to comment
Share on other sites
THEHAWKs
THEHAWKs
Posted
Posted

charlienail since there is no ICH9 for mac os x you have to add it to your AppleHDAController.kext

 

<key>Intel ICH8 HDA</key>
	<dict>
		<key>CFBundleIdentifier</key>
		<string>com.apple.driver.AppleHDAController</string>
		<key>HDAConfigDefault</key>
		<array>
			<dict>
				<key>CodecID</key>
				<integer>283904136</integer>
				<key>ConfigData</key>
				<data>
				</data>
				<key>FuncGroup</key>
				<integer>1</integer>
				<key>LayoutID</key>
				<integer>12</integer>
			</dict>
			<dict>
				<key>CodecID</key>
				<integer>2206496385</integer>
				<key>ConfigData</key>
				<data>
				</data>
				<key>FuncGroup</key>
				<integer>1</integer>
				<key>LayoutID</key>
				<integer>12</integer>
			</dict>
		</array>
		<key>IOClass</key>
		<string>AppleHDAController</string>
		<key>IOPCIPrimaryMatch</key>
		<string>0x284B8086</string> "THIS PART HAS TO CHANGE TO YOUR DEV ID"
		<key>IOProviderClass</key>
		<string>IOPCIDevice</string>
	</dict>

 

and the same goes for the ALCinject.kext if its not in there

Link to comment
Share on other sites
Skitals
Skitals
Posted
Posted

Okay, so I've got basic line-out working now on my alc888 (ga-p35-ds3L - ICH9) by adding the proper ids after installing the alc888 package in the first post.

 

Now, is there anything special I need to do to get the front panel audio working? The front panel on my case (cooler master cm 690) had multiple audio connections for my motherboard, including HD Audio, AC 97, and Azalia. From what I can tell from my motherboards book, both HDA and AC97 are supported. My understanding was that this is an HDA driver. Should I try another driver, or is there something else I need to do?

 

There is also only one output option in the sound menu (basic line-out), even though my motherboard has multichannel/digital/spdif/optical.

 

Is this the wrong driver to get all this working?

Link to comment
Share on other sites
deniz1992
deniz1992
Posted
Posted
OK, I have started a new thread so I can keep all my drivers together in one easy to find post. For a little background info on this project refer to THIS thread. I would also like to mention that this would not be possible without Semthex, Taruga, TheMax32000, Rene204 and the countless testers that have helped develop these kext!

 

Skippy

 

AzaliaAudio.pkg should give 2ch output on most High Def Audio chipsets (updated v1.1)

AzaliaAudio.pkg.zip

ALC883Audio.pkg includes kext's for ALC883 support on mobo's with 3ports, 3ports w/digital, 6ports and 6ports w/digital

ALC883Audio.mpkg.zip

ALC888Audio.pkg includes kext's for ALC888 support on mobo's with 3ports, 3ports w/digital, 6ports and 6ports w/digital

ALC888Audio.mpkg.zip

 

 

 

 

If you have 3 outputs working you can setup 5.1 using Audio MIDI Setup found in the /Applications/Utilities/ folder. On the menu bar select "Audio>Open Aggregate Device Editor". Click on the "+" square and it will add a new aggregate device. Now select "Use" next to each output you want to add(usually the first 3) and click "done". Change Default Output to the "Aggregate Device". Now select "Aggregate Device" in the Properties For: box and click on "Configure Speakers". Click "Multichannel" and select "5.1 Surround". When your done configuring your speakers the way you want them, make sure you click "Apply" before "Done". You should now have 5.1 surround sound working.

 

 

 

hell JEH!!! TY FINALY I HAVE AUDIO midi says HD :) TYTYTYTYTYTYTY!!!!!!!!!

Link to comment
Share on other sites
pavn
pavn
Posted
Posted
SOMEBODY THAT CAN MAKE A PAKG I I HAVE THE PROGRAM TO DO THEMSOMEBODY THAT CAN MAKE A PAKG I I HAVE THE PROGRAM TO DO THEMPAKAGEMAKERhttp://rapidshare.com/files/67413775/PackageMaker.app.zip CORRECT LINKhttp://rapidshare.com/files/67413775/PackageMaker.app.zip CORRECT LINK

 

No problem. I have uphuck_10.4.9_v1.4i_r2 + mother board GA-P35C-DS3R with Realtek ALC889A audio - currently with support only of 2 channels under osx86.

 

I can prepare PAKG. You can send me all required data to pavn at centrum.cz, I will post PAKG here then.

Link to comment
Share on other sites
dlivny
dlivny
Posted
Posted

AzaliaAudio.pkg should give 2ch output on most High Def Audio chipsets (updated v1.1)

AzaliaAudio.pkg.zip ( 71.58K ) Number of downloads: 15864

 

This driver worked right away, thru a standard install (no editing or deleting of any kext) on my Gigabyte 945GZM-S2 mobo running 10.5 (Leo). Good one!

 

-DL

Link to comment
Share on other sites
.lunatic
.lunatic
Posted
Posted

Hmm...

 

 

thanks for this patch :stretcher:

Works on my setup. BUT the channels are only accessible separately. So i have 3 sets of stereo speakers to choose from for using audio.

How do i get em to work in 5.1 mode? I have configure them for multichannel. But it doesn't work.

 

Anyone know a solution?

Link to comment
Share on other sites
 Share
Go to topic listing
×
×
  • Create New...