Mork vom Ork Posted September 30, 2016 Share Posted September 30, 2016 Rev 3776 Screen Shot 2016-09-30 at 14.46.11.png I want to give a big THANK YOU MAN to all, who made this possible. Working like a charme here. Now looking for a DONATION button... Contribution done... and it's worth every penny. 4 Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2289655 Share on other sites More sharing options...
RehabMan Posted September 30, 2016 Share Posted September 30, 2016 Faking LPC device ID for older system versions springs to mind. Easy to use a codeless kext (aka injector kext) in that case. Note that you can't Fake LPC device-id with DSDT/Patches anyway (requires add-on SSDT or full DSDT patch). Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2289675 Share on other sites More sharing options...
Riley Freeman Posted September 30, 2016 Share Posted September 30, 2016 Easy to use a codeless kext (aka injector kext) in that case. Note that you can't Fake LPC device-id with DSDT/Patches anyway (requires add-on SSDT or full DSDT patch). I injected it with a SSDT back when I ran 10.6 on my X79. I knew Clover had a LPC fix but it's in DSDT->Fixes. Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2289726 Share on other sites More sharing options...
RehabMan Posted September 30, 2016 Share Posted September 30, 2016 I injected it with a SSDT back when I ran 10.6 on my X79. I knew Clover had a LPC fix but it's in DSDT->Fixes. Yes... many ways to do it: - add on SSDT - codeless kext - DSDT patch - Devices/Arbitrary - DSDT/Fixes But not really DSDT/Patches... Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2289733 Share on other sites More sharing options...
magnifico Posted September 30, 2016 Share Posted September 30, 2016 Rev 3776 Screen Shot 2016-09-30 at 14.46.11.png Hey Sergey..you are The Special One @ Mork about donation...if you wont...u can !!!! Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2289786 Share on other sites More sharing options...
davidm71 Posted September 30, 2016 Share Posted September 30, 2016 Hi, Was wondering I noticed that the NVME-Express driver in Clover has grown like 8 kb since 3330 version release. Was wondering what has changed? More NVME drive support? Thanks 1 Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290086 Share on other sites More sharing options...
B-San Posted September 30, 2016 Share Posted September 30, 2016 Give THIS OSXAptioFixDRV-64.efi a try. It helped me with the same Thunderbold 2 AIC card problems. The default CLOVER driver always gives me a memory-allocation-error, which the attached one from link will fix it. Thank you very much, but my initial attempt would not allow bootup. I noticed the file you provided is from Oct. 2015, while the file I previously had in there (OsxAptioFix2Drv-64.efi, which I obtained from the following: https://nickwoodhams.com/x99-hackintosh-osxaptiofixdrv-allocaterelocblock-error-update/)is from May 2016. It may seem that my problem is more specific to the X-99 platform? Once again thank you, and I'll be looking forward to any more thoughts that you or anyone else on this forum may have! Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290095 Share on other sites More sharing options...
LockDown Posted October 1, 2016 Share Posted October 1, 2016 hello... i have an issue/bug to report. Asus socket 775 board without AHCI feature & C2Duo CPU. boot6 is ok, so no need to discuss that. boot7 reboots just when its about to load clover menu Any info? Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290111 Share on other sites More sharing options...
davidm71 Posted October 1, 2016 Share Posted October 1, 2016 Rev 3776 Screen Shot 2016-09-30 at 14.46.11.png This could fix my multi boot issue where different installations that show up in Clover all load the same config.plist file. Is it possible to now set a default config.plist file for every installation as well? Thanks. PS: I am so impressed with Clover. You devs are doing a great job! Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290119 Share on other sites More sharing options...
Slice Posted October 1, 2016 Share Posted October 1, 2016 hello... i have an issue/bug to report. Asus socket 775 board without AHCI feature & C2Duo CPU. boot6 is ok, so no need to discuss that. boot7 reboots just when its about to load clover menu Any info? This is not a bug report as you didn't provide a buggy code snippet. This is rather discussion what you are doing wrong. My system #4 in signature as well has socket 775 and Core2Duo and without AHCI. It works with boot7. Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290152 Share on other sites More sharing options...
LockDown Posted October 1, 2016 Share Posted October 1, 2016 how can i grab a log if instantly reboots? care to show me how please Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290162 Share on other sites More sharing options...
Slice Posted October 1, 2016 Share Posted October 1, 2016 how can i grab a log if instantly reboots? care to show me how please <key>Boot</key> <dict> <key>Debug</key> <true/> Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290170 Share on other sites More sharing options...
D-an-W Posted October 1, 2016 Share Posted October 1, 2016 Good morning folks, Would anyone be able to tell me if it is possible to have my Apple BROADCOM BCM94360CD WiFi card (Connected via a PCIe adapter) show up in the PCI section of System Report as I assume it does on a real Mac mini (I could be wrong but screenshots found on the Web suggest so)? Currently it only shows up in the Network section... I have tried adding an entry to the SMBIOS > Slots section of my Config.plist and also adding the fix "FixAirport_4000" but I ended up with it WiFi not working and an entry for a Dell WiFi card in the PCI section! With the FixAirport command enabled I see this in the Boot.log... 0:660 0:000 Start Airport Fix 0:660 0:000 found Airport device [001C0004:0] at 37C3 And Name is PXSX 0:660 0:000 Name PXSX present at 0xA2, renaming to ARPT 0:660 0:000 Name PXSX present at 0xE0, renaming to ARPT 0:660 0:000 AirportADR=37C3 add patch size=EA 0:660 0:000 adr 37C3 size of arpt=17 I don't use a custom DSDT which is why I added the FixAirport entry but with this entry added the system reports no WiFi is installed. Thanks for any advice! Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290206 Share on other sites More sharing options...
Slice Posted October 1, 2016 Share Posted October 1, 2016 Shown in System Profiler doesn't mean the adapter will works. Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290243 Share on other sites More sharing options...
D-an-W Posted October 1, 2016 Share Posted October 1, 2016 Sorry, I should have mentioned that the adapter works perfectly well (Oops!). Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290246 Share on other sites More sharing options...
Slice Posted October 1, 2016 Share Posted October 1, 2016 Sorry, I should have mentioned that the adapter works perfectly well (Oops!). And what is happen? It works in macOS until you shown it in System Profiler? Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290260 Share on other sites More sharing options...
D-an-W Posted October 1, 2016 Share Posted October 1, 2016 Basically yes, If I add "FixAirport_4000" then it is no longer detected by macOS. If I add the SMBIOS > Slots entry below without the Airport Fix I get a Dell WiFi card showing up but it doesn't work... <dict> <key>Device</key> <string>WIFI</string> <key>ID</key> <integer>2</integer> <key>Type</key> <integer>1</integer> <key>Name</key> <string>Airport</string> </dict> Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290263 Share on other sites More sharing options...
mrjayviper Posted October 1, 2016 Share Posted October 1, 2016 Hello. When do I use the kexts/others folder. I've always used the specific version folder. Example : kexts/10.11 Thanks Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290287 Share on other sites More sharing options...
Slice Posted October 1, 2016 Share Posted October 1, 2016 Hello. When do I use the kexts/others folder. I've always used the specific version folder. Example : kexts/10.11 Thanks Use others/ because it will apply for all system version. use kexts/10.11 if you are sure these kexts will work/needed only for 10.11. For example FakeSMC and VoodooHDA are system independent. Basically yes, If I add "FixAirport_4000" then it is no longer detected by macOS. If I add the SMBIOS > Slots entry below without the Airport Fix I get a Dell WiFi card showing up but it doesn't work... <dict> <key>Device</key> <string>WIFI</string> <key>ID</key> <integer>2</integer> <key>Type</key> <integer>1</integer> <key>Name</key> <string>Airport</string> </dict> Set NoDefaultProperties=true 2 Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290312 Share on other sites More sharing options...
gabryele Posted October 1, 2016 Share Posted October 1, 2016 I have 3 HD with other OS, Clover show me only the name "legacy hd1", "legacy hd2" etc is possible that Clover is not able to read the simply label of a hard disk?To identify the HD I must remember the number? Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290323 Share on other sites More sharing options...
Veron Posted October 1, 2016 Share Posted October 1, 2016 Is it possible to fix this small windows where you choose which drive to mount (EFI mount)?Before update for SIerra, windows showed all drives (EFI) without scroll. Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290336 Share on other sites More sharing options...
D-an-W Posted October 1, 2016 Share Posted October 1, 2016 Set NoDefaultProperties=true That did help a little as WiFi still works and now I get this... I added the following to my Config.plist... Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290363 Share on other sites More sharing options...
Sphinx777 Posted October 1, 2016 Share Posted October 1, 2016 Hello. May you explain the meaning of this new flags inside Clover Configurator? Thanks. -gus_nosleep -gux_nomsi nv_spanmodepolicy=1 keepsyms=1 kextlog=0xffff -alcoff -shikioff Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290777 Share on other sites More sharing options...
davidm71 Posted October 1, 2016 Share Posted October 1, 2016 Hi. Was wondering how do you download the latest release of Clover ver 3776 or even 3781? Been trying to find a link without success. Thanks guys. Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290827 Share on other sites More sharing options...
fusion71au Posted October 2, 2016 Share Posted October 2, 2016 @davidm71, You can compile it yourself with @Micky1979's Build_Clover.command script (prerequisite: needs Xcode). Easiest to choose option 3 ---> downloads Clover source and compiles/builds the standard Clover package installer in the ~/src/edk2/Clover/CloverPackage/sym folder. Alternatively, choose option 2 first (to get latest Clover source & sync edk2), then option 6 or 7 to build the package installer. I have attached the BOOTX64.efi from Clover r3781 to this post (replace the one in your EFI partition's EFI/Boot folder and also EFI/CLOVER folder with BOOTX64.efi renamed as CLOVERX64.efi). To "clean" the build, use terminal.... cd ~/src/edk2/Clover ./ebuild.sh cleanall ./ebuild.sh cleanpkg BOOTX64.zip Link to comment https://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page/445/#findComment-2290840 Share on other sites More sharing options...
Recommended Posts