Jump to content

Clover General discussion

ErmaC

By ErmaC,
in Clover

 Share
29,866 posts in this topic

Recommended Posts

chris1111
chris1111
Posted
Posted

After update to high sierra on ssd disk which convert to apfs filesystem now on clover boot screen i have two partitions.A preboot and the default mac drive.which one i must select?

 

 

Sent from my iPhone using Tapatalk

Boot to Default mac drive

 

You can hide Preboot with Clover configurator or manually

 

captu175.png
 

  • Like 2
Link to comment
Share on other sites
ephantom
ephantom
Posted
Posted

@Slice

 

 
Without more information, debug information I can't know what is your problem. May be you need to override PartitionDxe.efi.
 

 

Here is my debug.log.

 

 

 

0:100  0:100  MemLog inited, TSC freq: 2833008638
0:100  0:000  LegacyRegion2: Chipset/proc: 0x2E208086
0:100  0:000   Intel Series 4 and similar (PAM 0x90-0x96)
0:100  0:000   Test PAM1=(0x41=90, 0x5a=00, 0x81=00, 0x91=11) at chipset 2E208086
0:100  0:000  , Install = Success
0:110  0:010  BiosVideoDriverBindingStart!
0:110  0:000  BiosVideoCheckForVbe
0:110  0:000  EdidOverride not found
0:291  0:180   Edid1-
0:352  0:061   Edid0+
0:352  0:000   found Detail Timing 1280x1024
0:381  0:029     0 640x480 attr=3BF - ok, edid+, 640x480, working, highest, pref=0
0:382  0:000     1 800x600 attr=3BF - ok, edid+, 800x600, working, highest, pref=1
0:383  0:000     2 1024x768 attr=3BF - ok, edid+, 1024x768, working, highest, pref=2
0:384  0:000     3 1280x1024 attr=3BF - ok, edid+, working, highest, pref=3
0:389  0:004  BV new mode: 3 1280x1024
0:733  0:344   SetMode pref 3 (3) = Success
2:565  1:832  
2:565  0:000  Now is 26.9.2017,  22:35:20 (GMT)
2:565  0:000  Starting Clover revision: 4220 on CLOVER EFI
2:565  0:000  Build with: [Args: -D NO_GRUB_DRIVERS_EMBEDDED | -D NO_GRUB_DRIVERS_EMBEDDED -D USE_LOW_EBDA -a X64 -b RELEASE -t XCODE5 -n 5 | OS: 10.12.6 | XCODE: 8.3.3]
2:565  0:000  SelfDevicePath=PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(1,GPT,CF18F31C-DD95-40FA-A0F3-076B8249F7C1,0x28,0x64000) @CF010E98
2:565  0:000  SelfDirPath = \EFI\CLOVER
2:566  0:000  === [ Get Smbios ] ========================================
2:566  0:000  Type 16 Index = 0
2:566  0:000  Total Memory Slots Count = 4
2:566  0:000  Type 17 Index = 0
2:566  0:000  SmbiosTable.Type17->Speed = 800MHz
2:566  0:000  SmbiosTable.Type17->Size = 2048MB
2:566  0:000  SmbiosTable.Type17->Bank/Device = Bank0/1 A0
2:566  0:000  SmbiosTable.Type17->Vendor =  
2:566  0:000  SmbiosTable.Type17->SerialNumber =  
2:566  0:000  SmbiosTable.Type17->PartNumber =  
2:566  0:000  Type 17 Index = 1
2:566  0:000  SmbiosTable.Type17->Speed = 800MHz
2:566  0:000  SmbiosTable.Type17->Size = 2048MB
2:566  0:000  SmbiosTable.Type17->Bank/Device = Bank2/3 A1
2:566  0:000  SmbiosTable.Type17->Vendor =  
2:566  0:000  SmbiosTable.Type17->SerialNumber =  
2:566  0:000  SmbiosTable.Type17->PartNumber =  
2:566  0:000  Type 17 Index = 2
2:566  0:000  SmbiosTable.Type17->Speed = 800MHz
2:566  0:000  SmbiosTable.Type17->Size = 2048MB
2:566  0:000  SmbiosTable.Type17->Bank/Device = Bank4/5 A2
2:566  0:000  SmbiosTable.Type17->Vendor =  
2:566  0:000  SmbiosTable.Type17->SerialNumber =  
2:566  0:000  SmbiosTable.Type17->PartNumber =  
2:566  0:000  Type 17 Index = 3
2:566  0:000  SmbiosTable.Type17->Speed = 800MHz
2:566  0:000  SmbiosTable.Type17->Size = 2048MB
2:566  0:000  SmbiosTable.Type17->Bank/Device = Bank6/7 A3
2:566  0:000  SmbiosTable.Type17->Vendor =  
2:566  0:000  SmbiosTable.Type17->SerialNumber =  
2:566  0:000  SmbiosTable.Type17->PartNumber =  
2:566  0:000  Boot status=0
2:566  0:000  Running on: 'EP45-UD3P' with board 'EP45-UD3P'
2:566  0:000  === [ GetCPUProperties ] ==================================
2:566  0:000  CPU Vendor = 756E6547 Model=1067A
2:566  0:000   The CPU supported SSE4.1
2:566  0:000  got cores from CPUID_1 = 4
2:566  0:000   The CPU not supported turbo
2:566  0:000  BrandString = Intel(R) Core(TM)2 Quad CPU    Q9550  @ 2.83GHz
2:566  0:000  MSR dumps:
2:566  0:000   @0x00CD=80000A04
2:566  0:000   @0x0198=614481E0600481E
2:566  0:000  FSBFrequency = 470 MHz, DMI FSBFrequency = 333 MHz, Corrected FSBFrequency = 333 MHz
2:566  0:000  MaxDiv/MinDiv: 8.5/6
2:566  0:000  Turbo: 9/0/0/0
2:566  0:000  Features: 0xBFEBFBFF
2:566  0:000  Threads: 4
2:566  0:000  Cores: 4
2:566  0:000  FSB: 333 MHz
2:566  0:000  CPU: 4000 MHz
2:566  0:000  TSC: 4000 MHz
2:566  0:000  PIS: 1333 MHz
2:566  0:000  ExternalClock: 333 MHz
2:566  0:000  === [ GetDevices ] ========================================
2:566  0:000  PCI (00|00:00.00) : 8086 2E20 class=060000
2:566  0:000  PCI (00|00:01.00) : 8086 2E21 class=060400
2:566  0:000  PCI (00|01:00.00) : 10DE 0421 class=030000
2:566  0:000   - GFX: Model=Asus GeForce 8500 GT family 86 (Nvidia)
2:566  0:000  PCI (00|00:1A.00) : 8086 3A37 class=0C0300
2:566  0:000  PCI (00|00:1A.01) : 8086 3A38 class=0C0300
2:566  0:000  PCI (00|00:1A.02) : 8086 3A39 class=0C0300
2:566  0:000  PCI (00|00:1A.07) : 8086 3A3C class=0C0320
2:566  0:000  PCI (00|00:1B.00) : 8086 3A3E class=040300
2:566  0:000  PCI (00|00:1C.00) : 8086 3A40 class=060400
2:566  0:000  PCI (00|00:1C.03) : 8086 3A46 class=060400
2:566  0:000  PCI (00|03:00.00) : 197B 2363 class=010601
2:566  0:000  PCI (00|03:00.01) : 197B 2363 class=010185
2:566  0:000  PCI (00|00:1C.04) : 8086 3A48 class=060400
2:566  0:000  PCI (00|04:00.00) : 10EC 8168 class=020000
2:566  0:000   - LAN: 0 Vendor=Realtek
2:566  0:000  PCI (00|00:1C.05) : 8086 3A4A class=060400
2:566  0:000  PCI (00|05:00.00) : 10EC 8168 class=020000
2:566  0:000   - LAN: 1 Vendor=Realtek
2:566  0:000  PCI (00|00:1D.00) : 8086 3A34 class=0C0300
2:566  0:000  PCI (00|00:1D.01) : 8086 3A35 class=0C0300
2:566  0:000  PCI (00|00:1D.02) : 8086 3A36 class=0C0300
2:566  0:000  PCI (00|00:1D.07) : 8086 3A3A class=0C0320
2:566  0:000  PCI (00|00:1E.00) : 8086 244E class=060401
2:566  0:000  PCI (00|06:07.00) : 104C 8024 class=0C0010
2:566  0:000  PCI (00|00:1F.00) : 8086 3A16 class=060100
2:566  0:000  PCI (00|00:1F.02) : 8086 3A22 class=010601
2:566  0:000  PCI (00|00:1F.03) : 8086 3A30 class=0C0500
2:566  0:000  === [ GetDefaultSettings ] ================================
2:566  0:000  Clover load options size = 0 bytes
2:571  0:004  EFI\CLOVER\config.plist loaded: Success
2:571  0:000  === [ GetListOfThemes ] ===================================
2:571  0:000  - [00]: BGM
2:588  0:016  - [01]: embedded
2:598  0:010  - [01]: metal
2:601  0:002  - [02]: random
2:601  0:000  === [ Found config plists ] ===============================
2:601  0:000  - config.plist
2:611  0:009  === [ GetEarlyUserSettings ] ==============================
2:611  0:000  timeout set to 3
2:611  0:000  Custom boot CUSTOM_BOOT_DISABLED (0x0)
2:616  0:005  KextsToPatch: 2 requested
2:618  0:002   - [00]: AppleAHCIPort (External icons patch) :: BinPatch :: data len: 8
2:737  0:119   - [01]: AppleHDA (AppleHDA/Resources/xml>zml) :: BinPatch :: data len: 6
2:894  0:157  Default theme: embedded
2:896  0:001  Hiding entries with string Windows
2:898  0:001  Hiding entries with string \EFI\BOOT\BOOTX64.EFI
2:900  0:001  === [ LoadDrivers ] =======================================
3:055  0:155  Loading AppleImageCodec-64.efi  status=Success
3:061  0:006  Loading AppleKeyAggregator-64.efi  status=Success
3:067  0:006  Loading AppleUITheme-64.efi  status=Success
3:073  0:005  Loading FirmwareVolume-64.efi  status=Success
3:081  0:007  Loading FSInject-64.efi  status=Success
3:223  0:141  Loading SMCHelper-64.efi  status=Success
3:229  0:005  Loading UsbKbDxe-64.efi  status=Success
3:235  0:006   - driver needs connecting
3:237  0:001  1 drivers needs connecting ...
3:239  0:001  PlatformDriverOverrideProtocol->GetDriver overriden
3:287  0:047  === [ InitScreen ] ========================================
3:372  0:085  SetScreenResolution: 1920x1080 - not found!
3:376  0:004  Console modes reported: 4, available modes:
3:381  0:004   - [01]: 80x25
3:383  0:001   - [02]: 80x50
3:438  0:055   - [03]: 100x31
3:515  0:077   - [04]: 160x53 (current mode)
3:517  0:001  SetScreenResolution: 1280x1024 - already set
3:521  0:003  reinit: self device path=PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(1,GPT,CF18F31C-DD95-40FA-A0F3-076B8249F7C1,0x28,0x64000)
3:524  0:002  Using embedded font: Success
3:527  0:002  === [ GetMacAddress ] =====================================
3:606  0:078  === [ ScanSPD ] ===========================================
3:824  0:218  SMBus device : 8086 3A30 class=0C0500 status=Success
3:826  0:001  SMBus CmdReg: 0x3
3:828  0:001  Scanning SMBus [8086:3A30], mmio: 0xEA407004, ioport: 0x500, hostc: 0x1
3:830  0:002  Slots to scan [8]...
3:833  0:003  SPD[0]: Type 8 @0x50
3:843  0:009  DDR speed 800MHz
3:845  0:001  Slot: 0 Type 19 2048MB 800MHz Vendor=Crucial Technology PartNo= SerialNo=0F0F0F0F0F0F0F0F
3:847  0:002  SPD[1]: Type 8 @0x51
3:857  0:009  DDR speed 800MHz
3:859  0:002  Slot: 1 Type 19 2048MB 800MHz Vendor=Crucial Technology PartNo= SerialNo=0F0F0F0F0F0F0F0F
3:863  0:004  SPD[2]: Type 8 @0x52
3:873  0:009  DDR speed 800MHz
3:922  0:049  Slot: 2 Type 19 2048MB 800MHz Vendor=Crucial Technology PartNo= SerialNo=0F0F0F0F0F0F0F0F
4:000  0:077  SPD[3]: Type 8 @0x53
4:009  0:009  DDR speed 800MHz
4:011  0:001  Slot: 3 Type 19 2048MB 800MHz Vendor=Crucial Technology PartNo= SerialNo=0F0F0F0F0F0F0F0F
4:014  0:002  === [ GetAcpiTablesList ] =================================
4:225  0:211  Get Acpi Tables List from RSDT:
4:229  0:003   - [00]: FACP  GBTUACPI len=116
4:231  0:002   - [01]: EUDS   len=1280
4:233  0:001   - [02]: HPET  GBTUACPI len=56
4:235  0:001   - [03]: MCFG  GBTUACPI len=60
4:237  0:001   - [04]: APIC  GBTUACPI len=132
4:239  0:001   - [05]: SSDT  CpuPm len=939
4:241  0:001  Calibrated TSC Frequency = 2833008638 = 2833MHz
4:243  0:002  === [ GetUserSettings ] ===================================
4:319  0:076  USB FixOwnership: no
4:322  0:002   - final DSDT Fix mask=00009051
4:326  0:003  Using ProductName from config
4:328  0:001  ProductName: iMac14,2
4:386  0:057  Using latest BiosVersion from clover
4:463  0:076  BiosVersion: IM142.88Z.0123.B00.1708211454
4:465  0:001  BiosReleaseDate: 08/21/2017
4:466  0:001  Using FirmwareFeatures from clover
4:468  0:001  FirmwareFeatures: 0xE00FE137
4:470  0:001  Using FirmwareFeaturesMask from clover
4:472  0:001  FirmwareFeaturesMask: 0xFF1FFF3F
4:474  0:001  Using PlatformFeature from clover
4:476  0:001  PlatformFeature: 0x1
4:480  0:003  Board-ID set from config as Mac-27ADBB7B4CEE8E61
4:482  0:001  BoardType: 0xA
4:564  0:082  ChassisType: 0xD
4:642  0:077  === [ ScanVolumes ] =======================================
4:724  0:082  Found 9 volumes with blockIO
4:726  0:001  - [00]: Volume: PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)
4:730  0:004          Result of bootcode detection: bootable unknown (legacy)
4:732  0:001  - [01]: Volume: PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x4,0x0,0x0)
4:739  0:006          Result of bootcode detection: bootable unknown (legacy)
4:741  0:001  - [02]: Volume: PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(1,GPT,CF18F31C-DD95-40FA-A0F3-076B8249F7C1,0x28,0x64000)
4:873  0:132          Result of bootcode detection: bootable unknown (legacy)
4:875  0:001          This is SelfVolume !!
4:877  0:001  - [03]: Volume: PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(2,GPT,ED24C3B1-B836-4812-A1BB-76969466E560,0x64028,0x1D1A71F40)
4:914  0:036          Result of bootcode detection: bootable unknown (legacy)
4:918  0:003  - [04]: Volume: PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(3,GPT,F1097AC9-2163-405C-A4BD-D2B6CAAEE515,0x1D1AD5F68,0x135F20)
5:144  0:226  - [05]: Volume: PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(2,GPT,ED24C3B1-B836-4812-A1BB-76969466E560,0x64028,0x1D1A71F40)\HD(1,MBR,0x00000000,0x568F0326,0xFA8014)
5:299  0:154  - [06]: Volume: PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x4,0x0,0x0)\HD(1,GPT,21F65A35-6860-4619-802D-28F74D036C6A,0x28,0x64000)
5:305  0:006          Result of bootcode detection: bootable unknown (legacy)
5:320  0:015  - [07]: Volume: PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x4,0x0,0x0)\HD(2,GPT,A0EF9DFA-5B2A-47E1-88D8-9A666C2C1E7A,0x64028,0x3A1EB880)
5:473  0:153  - [08]: Volume: PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x4,0x0,0x0)\HD(3,GPT,BE462ADB-5E34-469F-A0C1-DEFE610ECB67,0x3A24F8A8,0x135F20)
5:657  0:183  PutNvramPlistToRtVars: nvram.plist not found
5:659  0:001  === [ InitTheme ] =========================================
5:745  0:086   using embedded theme
5:750  0:004  Using embedded font: Success
5:752  0:002  Choosing theme <null string>
5:806  0:054  after NVRAM boot-args=-v dart=0 nvda_drv=1 kext-dev-mode=1 rootless=0
5:884  0:077  Scanning legacy ...
5:886  0:001  === [ Dump SMC keys from NVRAM ] ==========================
5:942  0:056  found AppleSMC protocol
5:944  0:001  === [ ScanLoader ] ========================================
6:031  0:087  - [02]: 'EFI'
6:035  0:003  - [04]: 'Recovery HD'
6:039  0:004          AddLoaderEntry for Volume Name=Recovery HD
6:174  0:134  Icon 20 decoded, pointer CDB5DA98
6:176  0:002  - [06]: 'EFI'
6:285  0:108  - [07]: 'Hackintosh'
6:299  0:014          AddLoaderEntry for Volume Name=Hackintosh
6:320  0:020      Check if volume Is Hibernated:
6:322  0:001      Check sleep image 'by signature':
6:359  0:037      read prefs \Library\Preferences\com.apple.PowerManagement.plist status=Success
6:361  0:001      using default sleep image name = \private\var\vm\sleepimage
6:381  0:020      sleepimage not found -> Not Found
6:385  0:003      hibernated: no - sign
6:388  0:002  Icon 17 decoded, pointer CDB5D198
6:459  0:071  - [08]: 'Recovery HD'
6:538  0:078          AddLoaderEntry for Volume Name=Recovery HD
6:564  0:025  === [ AddCustomTool ] =====================================
6:644  0:079  Icon 8 decoded, pointer CDA98A98
6:686  0:041  found tool \EFI\CLOVER\tools\Shell64U.efi
6:688  0:001  Checking EFI partition Volume 2 for Clover
6:690  0:001   Found Clover
6:692  0:002  Icon 2 decoded, pointer CDA98518
6:696  0:004  Icon 1 decoded, pointer CD9FFD98
6:698  0:002  Icon 0 decoded, pointer CD9FFD18
6:764  0:066  Icon 5 decoded, pointer CD9FFC98
6:841  0:077  Icon 6 decoded, pointer CD9FFC18
6:844  0:002  === [ GetEfiBootDeviceFromNvram ] =========================
6:898  0:054  Default boot entry not found
6:900  0:001  DefaultIndex=-1 and MainMenu.EntryCount=9
6:902  0:002  Icon 21 decoded, pointer CD9FFB98
6:947  0:045  Icon 22 decoded, pointer CD9FFA18
6:950  0:002  Icon 23 decoded, pointer CD9FF998
6:962  0:012  Icon 11 decoded, pointer CD9FF598
6:965  0:002  GUI ready

p.p1 {margin: 0.0px 0.0px 0.0px 0.0px; font: 12.0px Helvetica}
span.Apple-tab-span {white-space:pre}
55:075  48:110  BootVariable of the entry is empty

 

 

 

The mappings should correspond with:

WDC WD5003ABYX-01WERA0
500.11 GB SATA
GUID Partition Map

   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *500.1 GB   disk1
   1:                        EFI EFI                     209.7 MB   disk1s1
   2:                  Apple_HFS Hackintosh              499.2 GB   disk1s2
   3:                 Apple_Boot Recovery HD             650.0 MB   disk1s3

HGST HMS5C4040BLE640
4 TB SATA
GUID Partition Map

   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *4.0 TB     disk0
   1:                        EFI EFI                     209.7 MB   disk0s1
   2:                  Apple_HFS Hacintosh Seirra        4.0 TB     disk0s2
   3:                 Apple_Boot Recovery HD             650.0 MB   disk0s3
Link to comment
Share on other sites
Badruzeus
Badruzeus
Posted
Posted

Ah OK, just tried Clover r4222 and glad to know that ShowOptimus=true gives me "Discrete" instead of "NotOptimus" on my laptop with single Nvidia  :)

so.., it works here. But how if this option checked but on a dual graphics laptop (for example Intel HD3000 + GT 640M) w/o switch option on BIOS, what info shown?

 

 

J2poPBX.jpg

 

Link to comment
Share on other sites
ajsurin
ajsurin
Posted
Posted

Hoping someone can help - I've had a working hack for almost 3 years, but all of a sudden any clover version > 4128 will cause the system to hang at the apple logo (In verbose mode, all I see is a line of '++++'s).  Re-installing 4128 brings everything back to normal.  I'm stuck upgrading to high sierra though because I can't update clover.  Anyone run into anything like this?

Link to comment
Share on other sites
Slice
Slice
Posted
Posted

Hoping someone can help - I've had a working hack for almost 3 years, but all of a sudden any clover version > 4128 will cause the system to hang at the apple logo (In verbose mode, all I see is a line of '++++'s).  Re-installing 4128 brings everything back to normal.  I'm stuck upgrading to high sierra though because I can't update clover.  Anyone run into anything like this?

Delete efi drivers specific for FileVault2.

  • Like 1
Link to comment
Share on other sites
Cyberdevs
Cyberdevs
Posted
Posted

@cyberdev,

following ur post here; I could confirm that using Clover r4222 (boot6-7) under 10.13-10.13.1 Beta for "Safe Mode (-x)" is working fine (on my 2nd gen mach & gf119). Thanks.

 

 

menRo2v.png

 

Thanks man :)

 

But unfortunately it doesn't work on my SkyLake rig. I tested with Clover r4212 and r4222 booting to macOS High Sierra 10.13.

 

It works normally on macOS Sierra 10.12.6 though.

Link to comment
Share on other sites
Slice
Slice
Posted
Posted

Can I please have that FakeSMC?

No problem. It is a part of HWSensors3, and included also in Clover repo in ThirdParty folder.

 

 

Great. With Clover r4223 + Slice's FakeSMC 3.5.0 + IOPCIFamily patch (NOP restoreMachineState call), hibernation with fv2 is working again. Thanks Slice. :)

Thanks for testing.

What is the PCIFamily patch you tell?

  • Like 2
Link to comment
Share on other sites
PMheart
PMheart
Posted
Posted

Thanks for testing.

What is the PCIFamily patch you tell?

This one: (Checked by myself, not sure if I've posted it anywhere else)

Kext: IOPCIFamily
Find: be040000 00e81793 0000
Repl: be040000 00909090 9090
Comment: Disable extendedConfigWrite16 under restoreMachineState
MatchOS: 10.12

OR

Kext: IOPCIFamily
Find: be040000 00e8d992 0000
Repl: be040000 00909090 9090
Comment: Disable extendedConfigWrite16 under restoreMachineState
MatchOS: 10.13

I guess HibernationFixup is also dealing with these stuffs via hooks, but I myself don't use Lilu very frequently. I still prefer Clover KextToPatch.

Link to comment
Share on other sites
Cyberdevs
Cyberdevs
Posted
Posted

No problem. It is a part of HWSensors3, and included also in Clover repo in ThirdParty folder.

 

It is a commits to the Repos

If you are Build Clover you are OK, the FakeSMC is in the ThirdParty

 

That's weird. I just downloaded Release350.zip from Slice's signature. (HWSensors3 for Intel and AMD)

Thanks a lot :)

Got it :)

 

You guys are the best :)

post-1011040-0-51711500-1506607725_thumb.png

Link to comment
Share on other sites
Slice
Slice
Posted
Posted

Why is the binary fakesmc in the repository? Why not the source code?

For those who can't compile.

Source code is in HWSensors3 repo.

This one: (Checked by myself, not sure if I've posted it anywhere else)

Kext: IOPCIFamily
Find: be040000 00e81793 0000
Repl: be040000 00909090 9090
Comment: Disable extendedConfigWrite16 under restoreMachineState
MatchOS: 10.12

OR

Kext: IOPCIFamily
Find: be040000 00e8d992 0000
Repl: be040000 00909090 9090
Comment: Disable extendedConfigWrite16 under restoreMachineState
MatchOS: 10.13

I guess HibernationFixup is also dealing with these stuffs via hooks, but I myself don't use Lilu very frequently. I still prefer Clover KextToPatch.

I want the same for 10.11.6 if needed.

Link to comment
Share on other sites
tluck
tluck
Posted
Posted

No nvram.plist on EFI even I have EMUVariableUefi.efi inside of DriverUEFI64? Why does not create new nvram.plist after restart?

The nvram.plist file is created by the rc scripts. Did you install those? Otherwise nothing is persisted if you use emuvariable.

Link to comment
Share on other sites
 Share
Go to topic listing
×
×
  • Create New...