Bronya Posted September 18, 2007 Author Share Posted September 18, 2007 Thank Bronya for your help, I just install your new driver with my Sapphire X1950 PRO 512MB PCIe, seem everything work fineexcept QE/CI and I already try all solution on this tread but still have no luck. So can help me a little bit more, how can I fix it? Thanks in advance. You do not forget write in terminal in single user boot : sudo -s also enter the password root! chown -R 0:0 /system/library/extensions chmod -R 755 /system/library/extensions rm /system/library/extensions.mkext rm /system/library/extensions.kextcache kextcache -k -z /system/library/extensions REBOOT ! If it has not helped, you will accept the driver ATINDRV.kext from Jcool ! In general, if at you works QE/CI through DVI>VGA through ATY_Wormy, to at you should work QE/CI on DVI through my driver ATY_Alopias! Link to comment Share on other sites More sharing options...
^kaneda Posted September 18, 2007 Share Posted September 18, 2007 it works, now i can manage 3d settings with ati panel... dind use new .kexy for atix1xxx since it dosent give me qe nor ci... and it shows 2 video cards in display at system profiler... Link to comment Share on other sites More sharing options...
Bronya Posted September 18, 2007 Author Share Posted September 18, 2007 ^kaneda,you show a photo in me work 3d setting . Link to comment Share on other sites More sharing options...
lightvin Posted September 18, 2007 Share Posted September 18, 2007 Hi !You test driver --> http://rapidshare.com/files/56461084/Ati_x...GT_Pro.mpkg.zip ! <-- work on DVI ! Thank Bronya for your help, I just install your new driver with my Sapphire X1950 PRO 512MB PCIe, seem everything work fine,but Dependencies is not satisfied and TVout does not work.Why? Link to comment Share on other sites More sharing options...
^kaneda Posted September 18, 2007 Share Posted September 18, 2007 sure, here its goes... ho... and i dont have ati tv out loadded :*(... .and why yous says in core image Hardware accelerated? ... Link to comment Share on other sites More sharing options...
R0GUE Posted September 18, 2007 Share Posted September 18, 2007 Hey Bronya, It finally works! Kudos to you my friend. The only thing I have noticed is that I get a secondary device showing up on the PCI bus in ASP. Its not a problem as the important one is working correctly. Just to reiterate, my card is a Sapphire Radeon X1950 Pro 512Mb AGP running through DVI - QE/CI, Rotation and resolution options all enabled. Thanks again Bronya! Link to comment Share on other sites More sharing options...
Scrizz Posted September 18, 2007 Share Posted September 18, 2007 Excellent Job Bronya! Can you please update your first post to reflect the changes? Link to comment Share on other sites More sharing options...
Trauma! Posted September 18, 2007 Share Posted September 18, 2007 Well Done, It's ok in here. Saphirre X1950 Pro 256 Mo PCIe. Good Job!!!!! Link to comment Share on other sites More sharing options...
Bronya Posted September 18, 2007 Author Share Posted September 18, 2007 Scrizz and all , the post 1 is updated ! lightvin, you edit info.plist in atitvout.kext and write in terminal : kextload /system/library/extensions/atitvout.kext sync reboot ^kaneda, you replace atiradeonx1000.kext and checkup ... At me too not show TV... In the control panel adjustment TV does not show! How to include, I yet do not know... Link to comment Share on other sites More sharing options...
dazulrich Posted September 19, 2007 Share Posted September 19, 2007 Hi Bronya, after a bit of fiddling - its all good now. Thanks so much! Me using ASUS 1950 Pro 356MB PCIe. one last thing. how do I get the ATI control panel installed.. in the jcool threat about the 1950xt is a post about a hacked install, but do I need to stick to a particular order and are the same steps needed ? /Daz Link to comment Share on other sites More sharing options...
^kaneda Posted September 19, 2007 Share Posted September 19, 2007 Scrizz and all , the post 1 is updated ! lightvin, you edit info.plist in atitvout.kext and write in terminal : kextload /system/library/extensions/atitvout.kext sync reboot ^kaneda, you replace atiradeonx1000.kext and checkup ... At me too not show TV... In the control panel adjustment TV does not show! How to include, I yet do not know... after i installed the full pack i lost ci and qe, and if i change the id in .plist i get a kernel panic... Link to comment Share on other sites More sharing options...
lightvin Posted September 19, 2007 Share Posted September 19, 2007 Scrizz and all , the post 1 is updated ! lightvin, you edit info.plist in atitvout.kext and write in terminal : kextload /system/library/extensions/atitvout.kext sync reboot ^kaneda, you replace atiradeonx1000.kext and checkup ... At me too not show TV... In the control panel adjustment TV does not show! How to include, I yet do not know... Thank you Bronya. Which modifications I must make "ATITVout"? Link to comment Share on other sites More sharing options...
Bronya Posted September 19, 2007 Author Share Posted September 19, 2007 after i installed the full pack i lost ci and qe, and if i change the id in .plist i get a kernel panic... You download ATI_ID_7288.zip in post 1 and the work If does not work, show me a photo! lightvin, nope modifications ! I try to find a problem... Link to comment Share on other sites More sharing options...
Bluejacky Posted September 19, 2007 Share Posted September 19, 2007 Hi !You test driver --> http://rapidshare.com/files/56461084/Ati_x...GT_Pro.mpkg.zip ! <-- work on DVI ! Hi, does this pack work well on 1950GT PCIE 256MB? BTW, which card do you think is better, ATI 1950GT PCIE 256 or NV Geforce 7300GT PCIE 256? Thanks a lot! Link to comment Share on other sites More sharing options...
Bronya Posted September 19, 2007 Author Share Posted September 19, 2007 Hi, does this pack work well on 1950GT PCIE 256MB?Yes !BTW, which card do you think is better, ATI 1950GT PCIE 256 or NV Geforce 7300GT PCIE 256?Thanks a lot!This your desire, you can try difference of acceleration of a two videocards!Hi Bronya,after a bit of fiddling - its all good now. Thanks so much!Me using ASUS 1950 Pro 356MB PCIe. one last thing. how do I get the ATI control panel installed.. in the jcool threat about the 1950xt is a post about a hacked install, but do I need to stick to a particular order and are the same steps needed ?/DazWhat for to you the driver from Jcool? If for you works excellently. That leave and play! Link to comment Share on other sites More sharing options...
Bluejacky Posted September 19, 2007 Share Posted September 19, 2007 Yes !This your desire, you can try difference of acceleration of a two videocards!What for to you the driver from Jcool? If for you works excellently. That leave and play! Hi, thank you for you help. I need a card can do some finalcut work, and I just bought a 7300GT to replace the 1950GT, but now I need to reconsider it. I will try this pack and report the result here. Thank you! Link to comment Share on other sites More sharing options...
dazulrich Posted September 19, 2007 Share Posted September 19, 2007 What for to you the driver from Jcool? If for you works excellently. That leave and play! I use your driver package. But I think I saw on one of your screenshots that you have the ATi control panel. And I just wonder how you installed this... I also saw in the jcool thread a post where the ATI 1900 package was installed (for the control panel) I just don't want to ruin my running system by trying it this way. Link to comment Share on other sites More sharing options...
Bronya Posted September 19, 2007 Author Share Posted September 19, 2007 I use your driver package. But I think I saw on one of your screenshots that you have the ATi control panel. And I just wonder how you installed this... I also saw in the jcool thread a post where the ATI 1900 package was installed (for the control panel) I just don't want to ruin my running system by trying it this way. Bluejacky, ok ! dazulrich,You download https://a248.e.akamai.net/f/674/9206/0/www2.../MacX1900G5.dmg ! Download the latest X1900 G5 driver from ATI. Now we need to trick the installer into thinking we have a PowerMac G5. The installer will use sysctl to check the hw.model attribute. We are just going to temporarily replace the sysctl binary with something that always outputs what we want. Copy it somewhere safe. $ sudo cp /usr/sbin/sysctl /usr/sbin/sysctl.real Replace sysctl with a file with this: #!/bin/sh echo "PowerMac11,2" Make it executable: $ sudo chmod +x /usr/sbin/sysctl Run the installer just like anyone would. Do not restart your computer before completeing the next step. Put the real sysctl back. $ sudo mv /usr/sbin/sysctl.real /usr/sbin/sysctl Everything should Just Work. You’ll now have an ATI Displays preference pane where you can tweak all of the “secret” options. Link to comment Share on other sites More sharing options...
dazulrich Posted September 19, 2007 Share Posted September 19, 2007 Thanks Bronya. i saw that very same post, but was not sure it would override your drivers.... Link to comment Share on other sites More sharing options...
Nadeem Posted September 19, 2007 Share Posted September 19, 2007 Dimitrik Has finally done it , i have had no problems of my x1950pro with the previous build of drivers , but now the card is fully recognized under the system profiler , thats cool ! .. dont know about DVi , never used it , but i really think that what you did is a really great effort ... and you saved my card from being sold ! Thanks Dimitrik !!!!!!!! Link to comment Share on other sites More sharing options...
lightvin Posted September 19, 2007 Share Posted September 19, 2007 You download ATI_ID_7288.zip in post 1 and the work If does not work, show me a photo! lightvin, nope modifications ! I try to find a problem... Excuse me Bronya, but I don' t understood. Which are the modifications to make? Link to comment Share on other sites More sharing options...
Bronya Posted September 19, 2007 Author Share Posted September 19, 2007 Excuse me Bronya, but I don' t understood.Which are the modifications to make? You edit info.plist in atitvout.kext ... Link to comment Share on other sites More sharing options...
nikeita Posted September 19, 2007 Share Posted September 19, 2007 Hi Bronya Hi All, I do not understand one thing, Natit.kext. we need this kext or not with your new drivers? i have a Saphire ATI X1950GT 256 PCIe on a DVI monitor. i have not tried this new driver (17.9.2007) but before this any posted driver have done it. Only a Natit.kext posted from Scrizz is able to detect as an ATI 1950 series and give me full resolution bu without CI/QE... other drivers either do no recognize the card (ID 0x7288) or leave me on console text mode after running loginwindow.app ( maybe work on dvi->vga ?? cannot try this) any help or explanation is very appreciated. bye Link to comment Share on other sites More sharing options...
Bronya Posted September 19, 2007 Author Share Posted September 19, 2007 Hi Bronya Hi All, I do not understand one thing, Natit.kext. we need this kext or not with your new drivers? i have a Saphire ATI X1950GT 256 PCIe on a DVI monitor. i have not tried this new driver (17.9.2007) but before this any posted driver have done it. Only a Natit.kext posted from Scrizz is able to detect as an ATI 1950 series and give me full resolution bu without CI/QE... other drivers either do no recognize the card (ID 0x7288) or leave me on console text mode after running loginwindow.app ( maybe work on dvi->vga ?? cannot try this) any help or explanation is very appreciated. bye You should have the new driver, it works on DVI and work QE/CI ! You should have natit.kext!!! Link to comment Share on other sites More sharing options...
Scrizz Posted September 19, 2007 Share Posted September 19, 2007 @BlueJacky x1950GT is much more powerful than 7300 Like I've said before, thanks goes to Bronya!!!! Link to comment Share on other sites More sharing options...
Recommended Posts