245 replies to this topic

[evulhotdog]

Finally got my DVD in the mail. So far I am doing pretty well. Was having some issues at first, due to my GTX480, it would hang at the mac address screen, all I had to do was boot with GraphicsEnabler=No and it worked perfectly. Now I am currently trying to get my PS/2 Keyboard to work properly. I have a USB mouse and a PS/2 Keyboard which will not work. I have a very cheap USB keyboard that works but its just bad. I dont know what to try anymore to be able to have a USB Mouse and a PS/2 Keyboard. Any tips?

[gecob]

Hi,
I'm trying to install my first hackintosh following this guide but whit no success.
I use the V2 boot loader, set the Bios as show in first page.
My configuration is:

Asus P6X58D
Intel i7 950
GeForce 8400GS
6GB of ram

when I boot with -x -v parameters the installation stop with this line:
ACPI_SMC_PlatformPluin::start-waitforsrvice(resourceMatching(AppleIntelCPUPowerManagement)time ut
yukon: Ethernet address "mac address"

if I boot with:  -x32 -v arch=i386 I get the error show here:

 20111004_003.jpg   740.79K   12 downloads

Can you help me?
Thanks

[Interloper]

Fist, Thanks a lot! Everything went nicely and easily on (so far):

P6x58D-E
Hardware Raid0 eSata Device with 4 drives. -volumes handled by external unit (was connected to marvel during install)
ati 6870


Install went 100% but now when bootloader suppose to be normal I get  
boot0: error
I can use 321 to boot into the OS which has NIC, no audio, not sure about firewire (but need it), shutdown works but not reboot -it hangs
First I had a problem at 29 minutes remaining. I noticed when I made my 2TB volume 1.5TB it reported 2tb during install and failed
I rebooted and created the full 2TB partition, then went 100% successful.

Is it the video card?


Again, Good job

Edit: Oh Gosh. I thought I printed the whole thread out, but it was only the first page. Perhaps my answer is there. I did try the manual method, to no avail.

[Interloper]

Still Boot0: error
When I sudo, after applying password I get _CFGetHostUUIDString: unable to determine UUID for host. Error: 35

I've reinstalled completely (for whatever dumb reason) following every exact step with no objections to no result.
But with hard drive unit connected to standard, non-Marvel ports
This is the same bootloader as whats on the CD?
Even with the manual modiify of disk part, nothing.





Hope thread isn't dead?

Edit: Guess I'm writing off a day to this one. Maybe someone will respond soon. Thanks

[cnote]

I'm finished the build on my second hack using a sabertooth x58 MB Bios 1304, 8g DDR3, and a PNY DDRV-258 graphics card.  I reset the bios and created a boot disk both per first post. My install DVD is 10.5.4.

After the boot CD boots cham I get is get the following error message:

EBIOS read error:  Error 0x01
  Block 0xfabe60 Sectors 0

EBIOS read error:  Error 0x01
  Block 0xfabe60 Sectors 0

EBIOS read error:  Error 0x01
  Block 0xfabe60 Sectors 0
EBIOS read error:  Error 0x01
  Block 0xfabe60 Sectors 0

I tried all combinations of boot commands, no luck.

Advise is appreciated!

[Tona102]

Ok, i know this thread is quite old, but my hackintosh is running great because of this guide, thanks again Kup!

But recently, i stumbled upon a strange problem, which is called iLok2! (i know, i know... but i need it, my machine is built specifically for music production!)


The weird thing is, EVERYTHING, including USB's works great. Only when i try to initialize plugin, which runs on a host software (Logic), and requires an iLok2, i have to wait somewhere between 5-10 minutes before i can work again, when it should be initialized not more than in about 1-3 seconds (slowest)! I already tested and ruled out iLok2 itself, on win7 (reaper) it works normally fast and on my MacBook (Logic) also!

I am still running SL 10.6.8


Please, help anyone! I cannot work, until i sort this out!



Toni