lottenow Posted July 6, 2020 Share Posted July 6, 2020 (edited) Many thanks for your support Devs! I am trying to boot from a Big Sur USB installer with OC installed on EFI partition. Here is what I get as I boot to macOS Installer Beta from the USB stick: I am using an Intel Nuc Hades Canyon (Intel i7-8809G / AMD Radeon RX Vega M GH 4 GB). I am confused as to why the ACPI is not recognized, as this works fine in Catalina. I also get a pre-linked kernel message before this, nonetheless, I have vsmcgen=1 on my boot-args. I have also updated all the Kexts to the latest builds, including OC from MacPato EFI, and disabled Intel ethernet kexts, as others had problems with it. See config attached and SSDTs. config.plist Any takers? Thanks in advance! Spoiler SSDT-Hpm.aml SSDT-Xhci.aml SSDT-OsxDetect.aml SSDT-PmEnable.aml SSDT-GpuSpoof.aml SSDT-TbtLegacy.aml Edited July 6, 2020 by lottenow Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728861 Share on other sites More sharing options...
MattsCreative Posted July 6, 2020 Share Posted July 6, 2020 Got the installer working on amd Ryzen Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728864 Share on other sites More sharing options...
MartinYTCZ Posted July 6, 2020 Share Posted July 6, 2020 Still getting SIGABRT with most kexts compiled using Lilu and Friends when trying to boot the Big Sur installer :// Here is my EFI in case anyone wants to take a look along with the error Any ideas are greatly appreciated Spoiler OC.zip Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728865 Share on other sites More sharing options...
MacPato Posted July 6, 2020 Share Posted July 6, 2020 Anyone with SIGABRT errors swap for FakeSMC and reset NVRAM Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728866 Share on other sites More sharing options...
MartinYTCZ Posted July 6, 2020 Share Posted July 6, 2020 (edited) 18 minutes ago, MacPato said: Anyone with SIGABRT errors swap for FakeSMC and reset NVRAM Didn't help for me :// 8th gen Kaby Lake R laptop by the way Edited July 6, 2020 by MartinYTCZ Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728867 Share on other sites More sharing options...
Club1 Posted July 6, 2020 Share Posted July 6, 2020 I can boot into the installer but none of my sata drives are listed in disk utility. Is there a fix for this? Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728871 Share on other sites More sharing options...
Donw35 Posted July 6, 2020 Share Posted July 6, 2020 what files do you have in the Drivers folder ? Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728872 Share on other sites More sharing options...
DMMA Posted July 6, 2020 Share Posted July 6, 2020 (edited) Well, it didn't work for me until I took working OC folder for my laptop and 1. Updated OC+drivers from provided folder 2. Not just updated kexts, but also removed all kexts that where not provided with updated OC 3. Added vsmcgen=1 to boot arguments I still get black screen on HD630 (mobile), with disabled acceleration I was able to boot installer, wipe the volume and install the files, but after reboot system wouldn't install without graphics acceleration (installer loads gui and then shuts down, same as installed system crashes without acceleration when you click Notification Center) With Clover, when booting installed system I can at least use external monitor. I guess I'll have to wait for HD630 support to be fixed or for Clover to be able to boot installer WhateverGreen got "Fix black screen on igfx since 10.15.5" commit yesterday, tried to boot with latest master but both Clover and OC still give black screen, both with -igfxtypec and without -igfxtypec both with usbc monitor and without it Edited July 6, 2020 by DMMA Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728873 Share on other sites More sharing options...
Club1 Posted July 6, 2020 Share Posted July 6, 2020 hfsplus, opencanopy and openruntime. The same I use for catalina Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728874 Share on other sites More sharing options...
Donw35 Posted July 6, 2020 Share Posted July 6, 2020 make sure they are set to enable Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728875 Share on other sites More sharing options...
dannyboy9 Posted July 6, 2020 Share Posted July 6, 2020 3 hours ago, Donw35 said: what files do you have in the Drivers folder ? coffee lake Spoiler Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728876 Share on other sites More sharing options...
Donw35 Posted July 6, 2020 Share Posted July 6, 2020 OC or CLOVER ? if OC, make sure all are enabled Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728879 Share on other sites More sharing options...
Club1 Posted July 6, 2020 Share Posted July 6, 2020 I have this in my config Spoiler Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728882 Share on other sites More sharing options...
Ivan999 Posted July 6, 2020 Share Posted July 6, 2020 I'm getting this issue booting the installer with the latest oc Spoiler Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728884 Share on other sites More sharing options...
Pavo Posted July 6, 2020 Share Posted July 6, 2020 3 minutes ago, eSaF said: I installed off the USB all the way to the Desktop but the strange thing is when I transferred the EFI Folder from the USB to the EFI partition of the hard drive it would not boot, clearing the NVRAM makes no difference. I think when installing, it takes a Snap Shot of the system including where the files came from, so when you take the USB out of the equation it won't boot because it is looking for the usb. Putting the usb back, the machine boots fine so we are not quite there yet me thinks It does take a snapshot but has nothing to do with the bootpicker ie.. OpenCore or Clover. The boot.efi is still located in the same location no matter using a bootpicker from USB or HDD. You should try booting with verbose and taking a look, I did have a long wait after 2nd phase was done to reach the setup phase. Most likely cause of the decrypting of the apfs volume is looking to use the T2 chip where hacks do not have these. It took about 10 minutes for it to fully decrypt it and boot. Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728890 Share on other sites More sharing options...
Club1 Posted July 6, 2020 Share Posted July 6, 2020 Just before I reach the installer the following message appears: IOAHCIBlockStorageDriver could not recover SATA HDD after 5 attempts, terminating In disk utility there are no sata drives listed Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728894 Share on other sites More sharing options...
Pavo Posted July 6, 2020 Share Posted July 6, 2020 6 minutes ago, eSaF said: @Pavo - Thanks for the clarification, I already have it running on a Test Disk but done the restored way, I am just trying like everyone to get it to install off a USB drive. I did reach all the way through the setup and to the desk top but transferring the EFI Folder and rebooting resulted in a panic but I will carry on playing with it to see what could be the cause of the glitch. BTW the whole initial process took roughly an hour to install off the usb drive. What did it panic on? Got a pic of the panic? Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728895 Share on other sites More sharing options...
bbmatias3 Posted July 6, 2020 Share Posted July 6, 2020 8 hours ago, augustopaulo said: Hi @bbmatias3, That's really nice - Thanks! I just added the "-v" (verbose) to boot arguments and unfortunately it stops booting as per picture... The BigSur image was "DD" copied from a VM installed image from Olarila, which boots on my Z390 Desktop with different EFI/OC. Spoiler Not sure double check your bios settings? Your laptop has 520 graphics? Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728897 Share on other sites More sharing options...
kushwavez Posted July 6, 2020 Share Posted July 6, 2020 8 hours ago, augustopaulo said: Hi @bbmatias3, That's really nice - Thanks! I just added the "-v" (verbose) to boot arguments and unfortunately it stops booting as per picture... The BigSur image was "DD" copied from a VM installed image from Olarila, which boots on my Z390 Desktop with different EFI/OC. Spoiler Verify that you have EC rename patches enabled (SSDT-EC, or rename patches in config.plist) Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728898 Share on other sites More sharing options...
dannyboy9 Posted July 6, 2020 Share Posted July 6, 2020 12 minutes ago, eSaF said: @Pavo - Sorry man I got so frustrated I scrapped the EFI Folder and now in the process of rebuilding to start again, any hiccups this time around, I will record and post. https://drive.google.com/file/d/1-Tt36j77uM9tiX-jNRVsB5huz05gd-v8/view?usp=sharing try my efi. used it on a 9600k/Gigabyte Z390/Rx 580 1 Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728899 Share on other sites More sharing options...
dannyboy9 Posted July 6, 2020 Share Posted July 6, 2020 2 hours ago, Club1 said: I have this in my config Hide contents don't need to have opencanopy.efi 4 minutes ago, eSaF said: @dannyboy9 - Hey thanks, as a matter of fact I did look at your EFI Folder and noticed as well as the config.plist you used, the Full Sample, the version is not 0.6.0, I don't know how much of a difference that makes but I shall battle on. well if it works for a nearly 95% spec'd system as yours, it ought to work for you too Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728901 Share on other sites More sharing options...
Club1 Posted July 6, 2020 Share Posted July 6, 2020 @dannyboy9 Still the same. Looks like I will need to wait Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728904 Share on other sites More sharing options...
bbmatias3 Posted July 6, 2020 Share Posted July 6, 2020 8 hours ago, augustopaulo said: Hi @bbmatias3, That's really nice - Thanks! I just added the "-v" (verbose) to boot arguments and unfortunately it stops booting as per picture... The BigSur image was "DD" copied from a VM installed image from Olarila, which boots on my Z390 Desktop with different EFI/OC. Spoiler my bros laptop is a dell e5570, i used the same efi but made a few changes. i also used the Olarila method. make sure to disable legacy rom options in bios. i tested this efi with big sur and its working https://drive.google.com/file/d/1m9na1S3bWxulcyLOkm47T179killBakV/view?usp=sharing Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728905 Share on other sites More sharing options...
bad_colne Posted July 6, 2020 Share Posted July 6, 2020 Hello there, i succeded to install BigSur on an Asus Rog G771JW with everything working. If someone could help me with some things: 1. When i try to restart my laptop the OS turns off, my screen turns off but my laptop stays on that statement and doesnt reboot so i have to force it to turn off. 2. When im trying to put it on sleep, it goes to sleep mode and after 10 second my laptop turns back on 3. how to remove "OCS: No scheme for BlacklistAppleUpdate at 3 index, context <Security>" from OpenCore boot? Thank you, Cornel EFI.zip Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728906 Share on other sites More sharing options...
dannyboy9 Posted July 6, 2020 Share Posted July 6, 2020 (edited) 23 minutes ago, eSaF said: @dannyboy9 - Yea you have a very valid point there, I will forge on with ver 0.6.0, if I fall down I will give your folder a run and report back. i was in no mood of making a plist for 0.6, but here it is for your satisfaction. config.plist Edited July 6, 2020 by dannyboy9 Link to comment https://www.insanelymac.com/forum/topic/344428-pre-release-macos-big-sur/page/4/#findComment-2728907 Share on other sites More sharing options...
Recommended Posts