Mr MagOO Posted April 27, 2013 Share Posted April 27, 2013 Hi all, Tried to upgrade from "old" 1242 in EFI partition to 1378 (new structure, so clean install ...). I'm stuck on DUET screen and no device detected to boot. Got an old bios mobo with a P45 chipset, ICH10R, one disk, only OSX. I had to reinstall OSX to use 1242 back but i really would like to continue upgrading my excellent Clover bootloader ! Please, can you help me ? thanks Link to comment Share on other sites More sharing options...
fau7i Posted April 28, 2013 Share Posted April 28, 2013 Hi all, Tried to upgrade from "old" 1242 in EFI partition to 1378 (new structure, so clean install ...). I'm stuck on DUET screen and no device detected to boot. Got an old bios mobo with a P45 chipset, ICH10R, one disk, only OSX. I had to reinstall OSX to use 1242 back but i really would like to continue upgrading my excellent Clover bootloader ! Please, can you help me ? thanks Most probably you forgot to update boot binary (stage 2) which is required in regard to new file structure. You have to run again the installer and choose to update MBR / PBR, then check installer log when finish to see if boot file is updated. Link to comment Share on other sites More sharing options...
Mr MagOO Posted April 28, 2013 Share Posted April 28, 2013 Thank you for your reply Tried to install 1378 in OSX partition and it worked well. Fresh install and same parameters but ´install in ESP´ option : fail + no way to boot even with my bootable usb key (clover 1242). Boot only with a chameleon usb key. I think that the installer is not good for legacy bios when esp install is chosen. Install log says that all is OK (even stage2) Link to comment Share on other sites More sharing options...
thatguy009 Posted April 28, 2013 Share Posted April 28, 2013 I can now boot into the clover gui, but when I try to boot into mac osx installation I get this when in verbose mode and it wont load any further. You guys got any clues with this? Help would be appreciated. Im thinking that I need to build a new kernel cache for the BaseSystem.dmg; which I added some kext to. Does anyone have an idea on how to do this? Link to comment Share on other sites More sharing options...
Slice Posted April 29, 2013 Share Posted April 29, 2013 Try boot with args "NoCaches" Link to comment Share on other sites More sharing options...
litmus Posted April 29, 2013 Share Posted April 29, 2013 Ok, I send the ID to Clover 1350 but it is not mean that it resolves all your problem. I think you should also do connector patch and switch off PatchVBios. Hi Slice, Thanks for your reply. I try the Clover r1378 from sourceforge, ths GUI is OK. So I do the ATI connector patch and switch off PatchVBios, then choose the Macintosh HD boot item. But the OSX ML can not boot correctly. It is blocked at the "System uptime in nanoseconds ........" This is my config.plist: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "[url="http://www.apple.com/DTDs/PropertyList-1.0.dtd"]http://www.apple.com/DTDs/PropertyList-1.0.dtd[/url]"> <plist version="1.0"> <dict> <key>PCI</key> <dict> <key>USBInjection</key> <string>Yes</string> <key>USBFixOwnership</key> <string>Yes</string> <key>InjectClockID</key> <string>Yes</string> </dict> <key>SystemParameters</key> <dict> <key>boot-args</key> <string>-v npci=0x2000 slide=0 NoKexts</string> <key>prev-lang:kbd</key> <string>en:0</string> <key>InjectSystemID</key> <string>Yes</string> <key>LegacyBoot</key> <string>PBR</string> </dict> <key>Graphics</key> <dict> <key>GraphicsInjector</key> <string>Yes</string> <key>FBName</key> <string>Ipomoea</string> <key>LoadVBios</key> <string>No</string> <key>VideoPorts</key> <string>3</string> <key>PatchVBios</key> <string>No</string> </dict> <key>KernelAndKextPatches</key> <dict> <key>KernelCpu</key> <string>Yes</string> <key>ATIConnectorsController</key> <string>6000</string> <key>ATIConnectorsData</key> <string>000400000403000000010000120401050008000004020000000100001102040310000000100000000001000000000002</string> <key>ATIConnectorsPatch</key> <string>000400000403000000010000120401030400000004020000000100001102040402000000100000000001000000000004</string> </dict> </dict> </plist> This is the syetem.log: 0:100 0:100 MemLog inited, TSC freq: 3292986520 0:100 0:000 0:100 0:000 Starting rEFIt rev 1378 on American Megatrends EFI 0:100 0:000 SelfDevicePath=PciRoot(0x0)/Pci(0x1f,0x2)/Sata(0x0,0x0)/HD(1,GPT,e7a67861-23c7-41d4-8969-4bdb59949b6d,0x800,0x64000) @D403AF98 0:100 0:000 SelfDirPath = \EFI\Boot 0:104 0:003 Theme: BootCamp Path: EFI\CLOVER\themes\BootCamp 0:113 0:009 Total Memory Slots Count = 4 0:115 0:001 Type 17 Index = 0 0:117 0:001 Ignoring insane frequency value 0MHz 0:119 0:001 SmbiosTable.Type17->Speed = 0 0:121 0:002 SmbiosTable.Type17->Size = 0 0:123 0:001 Type 17 Index = 1 0:125 0:001 SmbiosTable.Type17->Speed = 1600 0:127 0:001 SmbiosTable.Type17->Size = 8192 0:129 0:001 Type 17 Index = 2 0:131 0:001 Ignoring insane frequency value 0MHz 0:132 0:001 SmbiosTable.Type17->Speed = 0 0:134 0:001 SmbiosTable.Type17->Size = 0 0:136 0:001 Type 17 Index = 3 0:138 0:001 SmbiosTable.Type17->Speed = 1600 0:140 0:001 SmbiosTable.Type17->Size = 8192 0:142 0:002 Boot status=0 0:144 0:001 Clover revision: 1378 running on OptiPlex 7010 0:148 0:003 ... with board 0CNWVK 0:150 0:002 ConfigPlistPath: EFI\CLOVER\config.plist 0:153 0:002 Using OEM config.plist at path: EFI\CLOVER\config.plist 0:155 0:002 Loading early settings 0:157 0:001 LoadDrivers() start 0:160 0:003 Starting FSInject-64.efi 0:165 0:004 Using load options 'FSInject-64.efi ' 0:167 0:002 Starting OsxFatBinaryDrv-64.efi 0:171 0:003 Using load options 'OsxFatBinaryDrv-64.efi ' 0:174 0:002 Starting VboxHfs-64.efi 0:178 0:003 Using load options 'VboxHfs-64.efi ' 0:180 0:002 - driver needs connecting 0:182 0:001 Starting CsmVideoDxe-64.efi 0:186 0:003 Using load options 'CsmVideoDxe-64.efi ' 0:188 0:002 - driver needs connecting 0:190 0:001 Starting DataHubDxe-64.efi 0:194 0:003 Using load options 'DataHubDxe-64.efi ' 0:221 0:027 Starting EmuVariableUefi-64.efi 0:225 0:004 Using load options 'EmuVariableUefi-64.efi ' 0:227 0:002 EmuVariableUefi Initialize: VariableCommonInitialize = Success, orig services stored, install gEmuVariableControlProtocolGuid = Success 0:238 0:010 Starting OsxAptioFixDrv-64.efi 0:242 0:003 Using load options 'OsxAptioFixDrv-64.efi ' 0:244 0:002 Starting PartitionDxe-64.efi 0:248 0:003 Using load options 'PartitionDxe-64.efi ' 0:250 0:002 - driver needs connecting 0:252 0:001 Starting OsxLowMemFixDrv-64.efi 0:256 0:003 Using load options 'OsxLowMemFixDrv-64.efi ' 0:258 0:002 Starting HFSPlus-64.efi 0:263 0:004 Using load options 'HFSPlus-64.efi ' 0:265 0:002 - driver needs connecting 0:267 0:001 Starting NTFS-64.EFI 0:271 0:004 Using load options 'NTFS-64.EFI ' 0:273 0:002 - driver needs connecting 0:275 0:001 Starting VBoxExt2-64.efi 0:279 0:004 Using load options 'VBoxExt2-64.efi ' 0:281 0:002 - driver needs connecting 0:283 0:001 6 drivers needs connecting ... 0:285 0:001 PlatformDriverOverrideProtocol not found. Installing ... Success 0:289 0:003 Partition driver loaded: CD disconnect Success 0:294 0:005 Video driver loaded: disconnect Success 0:360 0:065 Searching for invalid DiskIo BY_DRIVER connects: not found, all ok 1:780 1:419 CsmVideoDriverBindingStart 1:782 0:001 mixed support=40010 1:783 0:001 Controller is [030000] 1:785 0:002 Check for VBE 1:832 0:046 0 1152x864 attr=BB - ok, edid+, working, highest, pref=0 1:844 0:011 1 1280x960 attr=BB - ok, edid- 1:850 0:005 2 640x480 attr=BB - ok, edid+, 640x480, working 1:860 0:010 3 800x600 attr=BB - ok, edid+, 800x600, working 1:870 0:009 4 1024x768 attr=BB - ok, edid+, 1024x768, working 1:879 0:009 5 1280x1024 attr=BB - ok, edid+, working, highest, pref=5 1:891 0:012 6 1400x1050 attr=BB - ok, edid- 1:898 0:006 7 1600x1200 attr=BB - ok, edid+, working, highest, pref=7 1:913 0:014 CsmVideo: New mode: 7 1600x1200 - set 3:849 1:935 - SetMode pref 7 (7) = Success 3:851 0:001 CsmVideoCheckForVbe - Success 3:853 0:001 CsmVideoDriverBindingStart end Success 3:858 0:005 CsmVideo: New mode: 4 1024x768 - blocking that switch 3:862 0:004 CsmVideo: New mode: 2 640x480 - blocking that switch 10:611 6:749 LoadDrivers() end 10:614 0:002 EmuVariable InstallEmulation: orig vars copied, emu.var.services installed, CreateEvent = Success, done 10:648 0:033 SetScreenResolution: 1920x1200 - not found! 10:651 0:003 reinit: self device path=PciRoot(0x0)/Pci(0x1f,0x2)/Sata(0x0,0x0)/HD(1,GPT,e7a67861-23c7-41d4-8969-4bdb59949b6d,0x800,0x64000) 10:654 0:002 new SelfHandle=D403AF98 10:656 0:002 CPU Vendor = 756E6547 Model=306A9 10:658 0:001 The CPU supported turbo 10:660 0:001 BrandString = Intel(R) Xeon(R) CPU E3-1230 V2 @ 3.30GHz 10:662 0:001 non-usable FLEX_RATIO = 110000 10:664 0:001 corrected FLEX_RATIO = 100000 10:666 0:001 FSBFrequency=100MHz 10:668 0:001 Corrected FSBFrequency=100MHz 10:670 0:001 Vendor/Model/Stepping: 0x756E6547/0x3A/0x9 10:671 0:001 Family/ExtFamily: 0x6/0x0 10:673 0:001 MaxDiv/MinDiv: 33.0/16 10:676 0:002 Turbo: 35/36/37/37 10:678 0:001 Features: 0xBFEBFBFF 10:679 0:001 Threads: 8 10:681 0:001 Cores: 4 10:683 0:001 FSB: 100 MHz 10:685 0:001 CPU: 3300 MHz 10:687 0:001 TSC: 3300 MHz 10:689 0:001 PIS: 400 MHz 10:691 0:001 PCI (00|00:00.00) : 8086 0158 class=060000 10:692 0:001 PCI (00|00:01.00) : 8086 0151 class=060400 10:694 0:001 PCI (00|01:00.00) : 1002 675D class=030000 10:696 0:001 PCI (00|01:00.01) : 1002 AA90 class=040300 10:698 0:001 PCI (00|00:14.00) : 8086 1E31 class=0C0330 10:700 0:002 PCI (00|00:16.00) : 8086 1E3A class=078000 10:702 0:001 PCI (00|00:16.01) : FFFF FFFF class=FFFFFF 10:704 0:001 PCI (00|00:16.03) : FFFF FFFF class=FFFFFF 10:706 0:001 PCI (00|00:19.00) : 8086 1502 class=020000 10:708 0:001 PCI (00|00:1A.00) : 8086 1E2D class=0C0320 10:710 0:001 PCI (00|00:1B.00) : 8086 1E20 class=040300 10:712 0:001 PCI (00|00:1D.00) : 8086 1E26 class=0C0320 10:714 0:001 PCI (00|00:1F.00) : 8086 1E47 class=060100 10:717 0:003 PCI (00|00:1F.02) : 8086 1E02 class=010601 10:719 0:001 PCI (00|00:1F.03) : 8086 1E22 class=0C0500 10:721 0:001 PCI (00|00:1F.06) : FFFF FFFF class=FFFFFF 10:723 0:001 ScanSPD() start 10:727 0:004 SMBus CmdReg: 0x3 10:729 0:001 Scanning SMBus [8086:1E22], mmio: 0xF7F35004, ioport: 0xF000, hostc: 0x1 10:752 0:022 SPD[1]: Type 11 @0x51 10:762 0:010 Using XMP Profile1, dropping previous frequency 1600MHz 10:764 0:001 DDR speed 2133MHz 10:766 0:001 Slot: 1 Type 24 8192MB 2133MHz Vendor=Team Group PartNo=Dark-1600 SerialNo=0101020800000404 10:790 0:023 SPD[3]: Type 11 @0x53 10:800 0:010 Using XMP Profile1, dropping previous frequency 1600MHz 10:802 0:001 DDR speed 2133MHz 10:804 0:001 Slot: 3 Type 24 8192MB 2133MHz Vendor=Team Group PartNo=Dark-1600 SerialNo=0101020800000809 10:927 0:122 ScanSPD() end 10:929 0:001 Calibrated TSC frequency =3292986520 =3292MHz 10:931 0:001 Loading main settings 10:932 0:001 Finally: Bus=99MHz CPU=3292MHz 10:935 0:002 load font image 10:947 0:012 font loaded from themedir 10:949 0:001 Font loaded: ImageWidth=176 ImageHeight=288 Ptr=D4354018 10:951 0:001 Font prepared WxH=11x18 CharWidth=10 10:953 0:002 found 9 volumes with blockIO 10:955 0:001 0. Volume: 10:957 0:001 PciRoot(0x0)/Pci(0x1f,0x2)/Sata(0x0,0x0) 10:961 0:004 Volume 'Whole Disc Boot', OS 'Legacy', GUID = <null guid> 10:963 0:001 1. Volume: 10:965 0:001 PciRoot(0x0)/Pci(0x1f,0x2)/Sata(0x1,0x0) 10:974 0:009 Volume 'Whole Disc Boot', OS '', GUID = <null guid> 10:977 0:002 2. Volume: 10:979 0:001 PciRoot(0x0)/Pci(0x1f,0x2)/Sata(0x2,0x0) 10:980 0:001 found optical drive 10:983 0:002 Volume 'Whole Disc Boot', OS '', GUID = <null guid> 10:985 0:001 3. Volume: 10:987 0:001 PciRoot(0x0)/Pci(0x1f,0x2)/Sata(0x0,0x0)/HD(1,GPT,e7a67861-23c7-41d4-8969-4bdb59949b6d,0x800,0x64000) 10:990 0:002 Icon 16 (icons\vol_internal_ntfs.icns) not found 10:992 0:002 Volume 'EFI', OS 'Windows', GUID = E7A67861-23C7-41D4-8969-4BDB59949B6D 10:996 0:003 This is SelfVolume !! 10:998 0:001 4. Volume: 11:000 0:001 PciRoot(0x0)/Pci(0x1f,0x2)/Sata(0x0,0x0)/HD(2,GPT,744be72e-b418-44c1-9116-17dd7548bf59,0x64800,0xaf000) 11:003 0:002 hiding this volume 11:004 0:001 Volume 'Legacy HD2', OS '', GUID = 744BE72E-B418-44C1-9116-17DD7548BF59 11:006 0:001 5. Volume: 11:008 0:001 PciRoot(0x0)/Pci(0x1f,0x2)/Sata(0x0,0x0)/HD(3,GPT,7b5af841-6bf2-4d06-8b05-af0df9bd777b,0x113800,0x7814000) 11:015 0:006 hiding this volume 11:017 0:001 Volume 'Windows8', OS 'Windows', GUID = 7B5AF841-6BF2-4D06-8B05-AF0DF9BD777B 11:018 0:001 6. Volume: 11:020 0:001 PciRoot(0x0)/Pci(0x1f,0x2)/Sata(0x0,0x0)/HD(4,GPT,3afaa524-4520-4991-86ce-341d7e70abe1,0x7927800,0x7514a88) 11:030 0:010 Booting OS 10.8.3 11:032 0:001 Volume '', OS 'Legacy', GUID = 3AFAA524-4520-4991-86CE-341D7E70ABE1 11:034 0:001 7. Volume: 11:036 0:001 PciRoot(0x0)/Pci(0x1f,0x2)/Sata(0x1,0x0)/HD(1,GPT,8c849a6a-6dc8-43af-9e0b-a588f88cd202,0x1000,0x31000) 11:041 0:005 hiding this volume 11:043 0:001 Volume 'EFI', OS 'Windows', GUID = 8C849A6A-6DC8-43AF-9E0B-A588F88CD202 11:045 0:001 8. Volume: 11:047 0:001 PciRoot(0x0)/Pci(0x1f,0x2)/Sata(0x1,0x0)/HD(2,GPT,9efeb627-349d-4e37-b0fc-15cd4c88e559,0x33000,0x15d4d738f) 11:053 0:005 hiding this volume 11:055 0:001 Volume 'Personal', OS 'Windows', GUID = 9EFEB627-349D-4E37-B0FC-15CD4C88E559 11:057 0:001 Searching volumes for latest nvram.plist ... 11:061 0:004 3. Volume 'EFI', GUID = E7A67861-23C7-41D4-8969-4BDB59949B6D - no nvram.plist - skipping! 11:065 0:003 5. Volume 'Windows8', GUID = 7B5AF841-6BF2-4D06-8B05-AF0DF9BD777B - no nvram.plist - skipping! 11:069 0:004 6. Volume '', GUID = 3AFAA524-4520-4991-86CE-341D7E70ABE1 - no nvram.plist - skipping! 11:073 0:003 7. Volume 'EFI', GUID = 8C849A6A-6DC8-43AF-9E0B-A588F88CD202 - no nvram.plist - skipping! 11:077 0:003 8. Volume 'Personal', GUID = 9EFEB627-349D-4E37-B0FC-15CD4C88E559 - no nvram.plist - skipping! 11:083 0:006 nvram.plist not found! 11:085 0:001 PutNvramPlistToRtVars: nvram.plist not found 11:087 0:001 Scanning loaders... 11:088 0:001 0: 'Whole Disc Boot' no file system 11:092 0:003 1: 'Whole Disc Boot' no file system 11:096 0:003 2: 'Whole Disc Boot' no file system 11:100 0:003 3: 'EFI' 11:107 0:007 added 'Boot Microsoft EFI boot menu from EFI' 11:113 0:005 added 'Boot UEFI boot menu from EFI' 11:114 0:001 4: 'Legacy HD2' no file system 11:119 0:004 5: 'Windows8' hidden 11:122 0:003 6: '' 11:128 0:005 Icon 15 (icons\vol_internal_hfs.icns) not found 11:134 0:006 added 'Boot Mac OS X from Macintosh HD' 11:137 0:003 7: 'EFI' hidden 11:141 0:003 8: 'Personal' hidden 11:145 0:003 Scanning legacy ... 11:147 0:001 0: 'Whole Disc Boot' hidden 11:150 0:003 1: 'Whole Disc Boot' hidden 11:154 0:003 2: 'Whole Disc Boot' hidden 11:158 0:003 3: 'EFI' not legacy 11:161 0:003 4: 'Legacy HD2' hidden 11:166 0:004 5: 'Windows8' hidden 11:169 0:003 6: '' not legacy 11:173 0:003 7: 'EFI' hidden 11:177 0:003 8: 'Personal' hidden 11:187 0:010 FindDefaultEntry ... 11:189 0:001 FindStartupDiskVolume ... 11:191 0:001 GetEfiBootDeviceFromNvram: efi-boot-device-data not found 11:195 0:003 not found 11:197 0:001 Default boot entry not found 11:199 0:001 FindDefaultEntry() 11:200 0:001 SetScreenResolution: 1600x1200 - already set 11:388 0:187 GUI ready 16:060 4:672 StartLoader() start 16:144 0:083 Turbo=Y 16:146 0:001 MSR_IA32_MISC_ENABLE = 850089 16:148 0:001 Set turbo: MSR_IA32_MISC_ENABLE = 850089 16:150 0:001 add table 9 #0 16:152 0:001 add table 9 #1 16:154 0:001 no airport 16:156 0:002 Trusting SMBIOS... 16:158 0:001 Channels: 2 16:160 0:001 Interleave: 0 2 1 3 4 6 5 7 8 10 9 11 12 14 13 15 16 18 17 19 20 22 21 23 16:208 0:048 SMBIOS Type 17 Index = 0 => 0 0: 16:210 0:001 BANK0 DIMM0 EMPTY 16:212 0:001 SMBIOS Type 17 Index = 1 => 2 2: 16:215 0:003 BANK1 DIMM0 EMPTY 16:217 0:001 SMBIOS Type 17 Index = 2 => 1 1: 16:219 0:001 BANK0 DIMM1 2133MHz 8192MB 16:221 0:001 mTotalSystemMemory = 8192 16:223 0:001 SMBIOS Type 17 Index = 3 => 3 3: 16:225 0:001 BANK1 DIMM1 2133MHz 8192MB 16:227 0:001 mTotalSystemMemory = 16384 16:228 0:001 NumberOfMemoryDevices = 4 16:230 0:001 Type20[0]->End = 0x7FFFFF, Type17[2] = 0x0 16:232 0:001 Type20[1]->End = 0xFFFFFF, Type17[3] = 0x0 16:234 0:001 Table 131 is present, CPUType=35 16:237 0:002 Change to: 704 16:238 0:001 RSDT 0xDBFF4028 16:240 0:001 FADT from RSDT: 0xDBFF4100 16:242 0:001 XSDT 0xDBFF4080 16:244 0:001 FADT from XSDT: 0xDBFFD7B0 16:246 0:001 Xsdt reallocation done 16:248 0:001 old FADT length=10C 16:253 0:004 DSDT found in Clover volume OEM folder: EFI\CLOVER\ACPI\patched\DSDT.aml 16:255 0:002 Apply DsdtFixMask=0x0000 16:506 0:250 Drop tables from Xsdt, count=11 16:508 0:001 Found table: FACP CBX3 16:510 0:001 Found table: APIC CBX3 16:512 0:002 Found table: FPDT CBX3 16:514 0:001 Found table: MCFG CBX3 16:516 0:001 Found table: HPET CBX3 16:518 0:001 Found table: SSDT SataTabl 16:519 0:001 Found table: SSDT Cpu0Ist 16:521 0:001 Found table: SSDT CpuPm 16:523 0:001 Found table: ASF! HCG 16:525 0:001 Found table: SLIC CBX3 16:527 0:001 Found table: BGRT 16:529 0:001 corrected XSDT length=124 16:531 0:002 CPUBase=0 and ApicCPUBase=1 ApicCPUNum=8 16:534 0:002 Booting OS 10.8.3 16:537 0:002 EdidDiscovered size=128 16:538 0:001 00 | 00 FF FF FF FF FF FF 00 0C E3 16:561 0:022 10 | 6E 07 01 01 01 01 20 11 01 03 16:583 0:022 20 | 80 34 21 78 EA C9 05 A3 57 4B 16:605 0:022 30 | 9C 25 12 50 54 21 08 00 81 80 16:627 0:022 40 | D1 00 71 40 81 C0 B3 00 8B C0 16:650 0:022 50 | 95 00 A9 40 28 3C 80 A0 70 B0 16:672 0:022 60 | 23 40 30 20 36 00 07 44 21 00 16:694 0:022 70 | 00 1E 00 00 00 FF 00 53 37 33 16:717 0:022 80 | 32 34 44 33 33 35 31 37 37 39 16:741 0:024 90 | 00 00 00 FD 00 38 3D 1E 53 0E 16:763 0:022 100 | 00 0A 20 20 20 20 20 20 00 00 16:785 0:022 110 | 00 FC 00 4D 32 34 45 49 35 0A 16:808 0:022 120 | 20 20 20 20 20 20 00 58 70 74 16:830 0:022 Framebuffer @0xE0000000 MMIO @0xF7E20000 I/O Port @0x0000E000 ROM Addr @0xF7E00000 16:832 0:002 ATI card POSTed, 16:836 0:003 Set VRAM for Cedar=1024Mb 16:838 0:001 ATI: get_vram_size returned 0x40000000 16:840 0:001 ATI Radeon EVERGREEN family 16:842 0:002 ATI Mobile Radeon 16:844 0:001 Users config name Ipomoea 16:846 0:001 use N ports setting from config.plist: 3 16:848 0:001 (AtiPorts) Nr of ports set to: 3 16:850 0:002 ATI Turks AMD Radeon HD 7570M Series 1024MB (Ipomoea) [1002:675D] (subsys [1028:2B20]):: PciRoot(0x0)/Pci(0x1,0x0)/Pci(0x0,0x0) 16:852 0:001 HDA Controller [1002:AA90] :: PciRoot(0x0)/Pci(0x1,0x0)/Pci(0x0,0x1) => HDMI Audio, setting hda-gfx=onboard-1 16:855 0:003 USB Controller [8086:1E31] :: PciRoot(0x0)/Pci(0x14,0x0) 16:858 0:002 LAN Controller [8086:1502] :: PciRoot(0x0)/Pci(0x19,0x0) 16:860 0:001 USB Controller [8086:1E2D] :: PciRoot(0x0)/Pci(0x1a,0x0) 16:862 0:001 HDA Controller [8086:1E20] :: PciRoot(0x0)/Pci(0x1b,0x0) => detected codec: 10EC:0269, setting layout-id=269 (0x10D) 16:867 0:005 USB Controller [8086:1E26] :: PciRoot(0x0)/Pci(0x1d,0x0) 16:869 0:001 stringlength = 5524 16:871 0:001 devprop_generate_string 16:873 0:002 CurrentMode: Width=1600 Height=1200 16:875 0:001 FSInjection:, skipping kext injection (kexts folder not found)OnSimpleFileSystem occured 16:883 0:007 - done! 16:887 0:003 Closing log 16:889 0:002 SetStartupDiskVolume ... Volume: '', LoaderPath: '<null string>' 16:890 0:001 DevPath: 16:892 0:001 GUID = 3AFAA524-4520-4991-86CE-341D7E70ABE1 16:894 0:001 efi-boot-device: <array><dict><key>IOMatch</key><dict><key>IOProviderClass</key><string>IOMedia</string><key>IOPropertyMatch</key><dict><key>UUID</key><string>3AFAA524-4520-4991-86CE-341D7E70ABE1</string></dict></dict></dict></array> 16:898 0:003 Starting boot.efi 17:207 0:308 Using load options 'boot.efi -v npci=0x2000 slide=0 NoKexts ' 35:733 18:526 Legacy USB Off Done 35:736 0:002 USB EHCI Ownership for device 1E2D value=1000001 35:738 0:002 Legacy USB Off Done 35:741 0:002 USB EHCI Ownership for device 1E26 value=1000001 This is the screenshot of boot screen: Link to comment Share on other sites More sharing options...
Slice Posted April 29, 2013 Share Posted April 29, 2013 Looks like you DSDT is not patched for HPET. Link to comment Share on other sites More sharing options...
monsti Posted April 30, 2013 Share Posted April 30, 2013 Does Clover actally work with virtual box? I am using Chameleon + virtual box to dualboot. - Win 7 with OSX virtualized - OSX with Win7 virtualized (both installed native) With Clover (ISO taken from sourceforge) i couln't get virtualbox booting. The Harddisk isn't detected. Is there a trick? Link to comment Share on other sites More sharing options...
Slice Posted April 30, 2013 Share Posted April 30, 2013 Does Clover actally work with virtual box? I am using Chameleon + virtual box to dualboot. - Win 7 with OSX virtualized - OSX with Win7 virtualized (both installed native) With Clover (ISO taken from sourceforge) i couln't get virtualbox booting. The Harddisk isn't detected. Is there a trick? I just don't know! Clover works on Qemu but we didn't install any system on it. About VirtualBox a huge investigations needed. Link to comment Share on other sites More sharing options...
monsti Posted April 30, 2013 Share Posted April 30, 2013 Ok I'll investe some time in that. Can you point me to a document on how to get Clover from SVN and compile it? Thx. Link to comment Share on other sites More sharing options...
k3nny Posted April 30, 2013 Share Posted April 30, 2013 @monsti: Take a look at CloverGrower. The script sets up the required environment to compile Clover and can be used to pull and build the newest revision. Link to comment Share on other sites More sharing options...
monsti Posted April 30, 2013 Share Posted April 30, 2013 Am I a CloverGrower or a "Pro" user? Not sure if I am l33t Link to comment Share on other sites More sharing options...
Mr MagOO Posted April 30, 2013 Share Posted April 30, 2013 hi, maybe a dumb question : is there anyway to install a new clover release (new folder structure) in EFI partition with an old legacy bios mobo (no UEFI) ? V1242 is the latest release that works for me with esp installation. Link to comment Share on other sites More sharing options...
Slice Posted May 1, 2013 Share Posted May 1, 2013 Am I a CloverGrower or a "Pro" user? Not sure if I am l33t At your will. hi, maybe a dumb question : is there anyway to install a new clover release (new folder structure) in EFI partition with an old legacy bios mobo (no UEFI) ? V1242 is the latest release that works for me with esp installation. Yes, it is possible and the installer must do this. Link to comment Share on other sites More sharing options...
68x Posted May 1, 2013 Share Posted May 1, 2013 How can I find my Clover boot log? Link to comment Share on other sites More sharing options...
tluck Posted May 1, 2013 Share Posted May 1, 2013 i have some regression issues to report with b1429 1) busspeed problem - clover now computes FSB as 34146kz vs ~100Mhz -it ignored an explicit setting of BusSpeedkHz in the config.plist 2) memory bank count wrong -even using SMBIOS Trust=No - it thinks there are 3 banks - when early on it finds just 2 banks (correctly) from the boot log $ grep -i hz boot.log boot.log:1:489 0:000 BrandString = Intel® Core i5-2520M CPU @ 2.50GHz boot.log:1:489 0:000 FSBFrequency=100MHz boot.log:1:489 0:000 Corrected FSBFrequency=100MHz boot.log:1:489 0:000 FSB: 100 MHz boot.log:1:489 0:000 CPU: 2500 MHz boot.log:1:489 0:000 TSC: 2500 MHz boot.log:1:489 0:000 PIS: 400 MHz boot.log:1:514 0:009 DDR speed 1333MHz boot.log:1:514 0:000 Slot: 0 Type 24 4096MB 1333MHz Vendor=Ramaxel Technology PartNo=RMT3020EC58E9F1333A SerialNo=040206030901010B boot.log:1:538 0:009 DDR speed 1333MHz boot.log:1:538 0:000 Slot: 1 Type 24 4096MB 1333MHz Vendor=Ramaxel Technology PartNo=RMT3020EC58E9F1333A SerialNo=04030C0D0509030A boot.log:1:815 0:000 Calibrated TSC frequency =2508515880 =2508MHz boot.log:1:815 0:000 Config set CpuFreq=2500MHz boot.log:1:815 0:000 Config set BusSpeed=34164kHz boot.log:1:815 0:000 Finally: Bus=34MHz CPU=2500MHz boot.log:84:416 0:000 Finally: Bus=34MHz CPU=2500MHz boot.log:93:280 0:000 Finally: Bus=34MHz CPU=2500MHz boot.log:94:392 0:000 Finally: Bus=34MHz CPU=2500MHz boot.log:153:109 0:000 BANK0 DIMM0 1333MHz 4096MB boot.log:153:109 0:000 BANK1 DIMM0 1333MHz 4096MB boot.log:153:109 0:000 BANK0 DIMM1 1333MHz 4096MB PS b1378 works fine. SMBIOS Trust=No - sorted memory ok. and BusSpeedkHz overrides bogus speed calculation of 100310 Link to comment Share on other sites More sharing options...
Maniac10 Posted May 1, 2013 Share Posted May 1, 2013 How can I find my Clover boot log? If you installed the RC scripts then the boot logs should be in /library/logs/clover. Don't know if it saves a log without the scripts. Link to comment Share on other sites More sharing options...
Mr MagOO Posted May 1, 2013 Share Posted May 1, 2013 At your will. Yes, it is possible and the installer must do this. Tried 3 fresh install and classical options of the installer : no success and no way to boot with my clover usb stick. After it is screwed, only boots with a chameleon usb stick. Please, help me. Edit : install done by using 'install in ESP' option, deleting the boot file, installing in main partition and copying the new boot file to EFI partition. Finished by deleting boot file and EFI folder in main partition and reboot. Hard to think it's the way it meant to be done ! Link to comment Share on other sites More sharing options...
Lordadmiral Drake Posted May 1, 2013 Share Posted May 1, 2013 I hit another wall. I wanted to try out Clover in UEFI mode. For that I installed it to a USB Stick and copied my config.plist and dsdt from the HDD to it. Clover itself loads fine, but if I try to boot OS X all I get is a black screen and some seconds of HDD activity. Then the system does nothing and I have to do a hard reboot Link to comment Share on other sites More sharing options...
68x Posted May 1, 2013 Share Posted May 1, 2013 If you installed the RC scripts then the boot logs should be in /library/logs/clover. Don't know if it saves a log without the scripts. Many thanks, I just found it. Link to comment Share on other sites More sharing options...
stayupforever909 Posted May 1, 2013 Share Posted May 1, 2013 Hello All I need some help please I have been trying to get Ivy bridge power management working with my new hack for about a month now with the sys def of Macmini6,2 and Clover UFEI boot. I have try'd many different versions of clover and am now working with 1360 all though this has always been from a USB stick,I have Chameleon 2186 installed to the hard drive (would this make a difference?). I have try'd with and without DSDT and SSDT. I have generated DSDT from OSX booted with Chameleon and clean DSDT booted from Lynx. I have generated SSDT in many different ways Macisal PikeRAlpha's IB SSDT generation script. I have googled and researched every where I can find, there must just be something I am missing or don't understand. The only real difference I can see is the SMC Version that loads with Chameleon vs Clover, Clover loads 2.8f0 and Chameleon 1.30f3 that enables speedstep Can anyone help I have try'd so many different combinations of config.plist fakeSMC DSDT SSDT could some one take the time to go over my Darwin Dumps DSDT SSDT and point me in the right direction Many thanks to all here DarwinDumper_2.6.5_AMI_X64_1360_ML_rootGenrateIvyStatesYes.zip SSDT.aml.zip SSDT.aml 2.zip config.plist.zip config.plist copy.zip Link to comment Share on other sites More sharing options...
k3nny Posted May 1, 2013 Share Posted May 1, 2013 ...I have been trying to get Ivy bridge power management working... What do you understand under ivy bridge power management or what are you trying to achieve exactly? Link to comment Share on other sites More sharing options...
thatguy009 Posted May 2, 2013 Share Posted May 2, 2013 Try boot with args "NoCaches" Still not working ): I get into the gui, press space, boot with no caches but it still hangs. Got anymore ideas of what might be wrong? Link to comment Share on other sites More sharing options...
stayupforever909 Posted May 2, 2013 Share Posted May 2, 2013 Sorry If my last post was unclear What do you understand under ivy bridge power management or what are you trying to achieve exactly? What I am trying to achive is Ivy bridge power managment with speed stepping. By this I mean loading the kexts x86PlatformPlugin.kext and x86PlatformShim and achiving more that 2 p-states. At the moment when I boot with Clover and the sys def Macmini6,2 I only achive 2 p-states of 16 and 34 and x86PlatformPlugin.kext and x86PlatformShim do not load. When I boot with Chameleon though x86PlatformPlugin.kext and x86PlatformShim load and I achive p-states of 16 20 26 30 34 39. I belive it has something to do with the SMC version (system) that loads. Chameleon is know to interact with fakeSMC and inject the SMC version 1.30f3. When Booting with Clover this does not happen and the correct SMC version for the sys def choice I have made is loaded. Is this something I can control through Clovers config.plist, or is there another way to get x86PlatformPlugin.kext and x86PlatformShim to load when booting with Clover. Thanks Link to comment Share on other sites More sharing options...
Slice Posted May 2, 2013 Share Posted May 2, 2013 Tried 3 fresh install and classical options of the installer : no success and no way to boot with my clover usb stick. After it is screwed, only boots with a chameleon usb stick. Please, help me. Edit : install done by using 'install in ESP' option, deleting the boot file, installing in main partition and copying the new boot file to EFI partition. Finished by deleting boot file and EFI folder in main partition and reboot. Hard to think it's the way it meant to be done ! Why so hard??? What is wrong in installer or elsewhere? See /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *500.1 GB disk0 1: EFI 209.7 MB disk0s1 2: Apple_HFS MacHD 270.5 GB disk0s2 3: Apple_Boot Recovery HD 650.0 MB disk0s3 4: Apple_HFS LionHD 118.9 GB disk0s4 5: Microsoft Basic Data Data 109.7 GB disk0s5 Disk0 sector 0 contains boot0 sector as well as Chameleon did. By dd command or by fdisk440 utility. Partition 1 is EFI System Partition formatted by default to FAT32. First sector contains boot1f32 as installed by dd command. /EFI folder with all files is placed on partition 1. All this is provided by Clover installer. You need no to do this manually. It works as legacy BIOS boot and also it works as UEFI boot. Is it too complex? Link to comment Share on other sites More sharing options...
Recommended Posts