Jump to content

[GUIDE] Scripted Yosemite/Mavericks Install on Gigabyte Mobos

digital_dreamer

By digital_dreamer,
in Tutorials (The Genius Bar)

 Share
4,696 posts in this topic

Recommended Posts

jrhende
jrhende
Posted
Posted

Updated to El Capitan preliminary GM.  Sleep doesn't work reliably.  Updated my Yosemite to use Clover to isolate the problem.  That configuration sleeps fine.  Something with El Capitan causes my EX58-UD5 to not reliably sleep.  Was going to transition to 10.11 permanently but now will have to wait until that problem is solved.  Any ideas would be appreciated.

Link to comment
Share on other sites
jrhende
jrhende
Posted
Posted (edited)

Ensured DSDT not used.  Using config.plist from my Yosemite partition that works perfect.  Same kext used as in Yosemite.  The result is that when sleep is started the system wakes right back up.  The log is as follows:

 

9/16/15 7:35:52.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:35:52.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:35:54.058 PM WindowServer[176] send_datagram_available_ping: pid 239 failed to act on a ping it dequeued before timing out.
9/16/15 7:35:59.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:35:59.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:36:02.536 PM AirPlayUIAgent[455] 2015-09-16 07:36:02.535637 PM [AirPlayUIAgent] BecomingInactive: NSWorkspaceWillSleepNotification
9/16/15 7:36:02.536 PM acwebsecagent[320] WebsecSleepCallBack: messageType e0000280, arg 0069000d
9/16/15 7:36:02.536 PM acwebsecagent[320] WebsecSleepCallBack: kIOMessageSystemWillSleep
9/16/15 7:36:02.591 PM WindowServer[176] device_generate_desktop_screenshot: authw 0x0(0), shield 0x7feb698f9400(2001)
9/16/15 7:36:02.624 PM WindowServer[176] device_generate_lock_screen_screenshot: authw 0x0(0)[inf, inf, 0, 0] shield 0x7feb698f9400(2001), dev [1920,1080]
9/16/15 7:36:02.625 PM WindowServer[176] device_generate_desktop_screenshot: authw 0x0(0), shield 0x7feb698f9400(2001)
9/16/15 7:36:02.682 PM identityservicesd[382] <IMMacNotificationCenterManager: 0x7ffe12914970>: notification observer: com.apple.iChat   notification: __CFNotification 0x7ffe12832d80 {name = _NSDoNotDisturbEnabledNotification}
9/16/15 7:36:02.693 PM identityservicesd[382] <IMMacNotificationCenterManager: 0x7ffe12914970>:    NC Disabled: NO
9/16/15 7:36:02.703 PM identityservicesd[382] <IMMacNotificationCenterManager: 0x7ffe12914970>:   DND Enabled: YES
9/16/15 7:36:02.703 PM identityservicesd[382] <IMMacNotificationCenterManager: 0x7ffe12914970>: Updating enabled: NO   (Topics: (
))
9/16/15 7:36:20.000 PM kernel[0] PM response took 3092 ms (56, powerd)
9/16/15 7:36:20.000 PM kernel[0] kern_open_file_for_direct_io(0)
9/16/15 7:36:20.000 PM kernel[0] kern_open_file_for_direct_io took 0 ms
9/16/15 7:36:20.000 PM kernel[0] Opened file /var/log/SleepWakeStacks.bin, size 172032, extents 1, maxio 2000000 ssd 1
9/16/15 7:36:20.000 PM kernel[0] polled file major 1, minor 8, blocksize 4096, pollers 5
9/16/15 7:36:25.000 PM kernel[0] en1: channel changed to 1
9/16/15 7:36:33.000 PM kernel[0] Wake reason: RTC USB0 (Alarm)
9/16/15 7:36:33.000 PM kernel[0] RTC: Maintenance 2015/9/17 03:36:17, sleep 2015/9/17 02:36:29
9/16/15 7:36:33.000 PM kernel[0] RTC: PowerByCalendarDate setting ignored
9/16/15 7:36:33.000 PM kernel[0] RTC: PowerByCalendarDate setting ignored
9/16/15 7:36:33.000 PM kernel[0] Previous sleep cause: 5
9/16/15 7:36:33.000 PM kernel[0] en1: channel changed to 1
9/16/15 7:36:34.027 PM hidd[100] [HID] [MT] MTSimpleHIDManager::deviceDidBootload device bootloaded
9/16/15 7:36:34.697 PM acvpnagent[51] The network interface for the VPN connection has gone down.
9/16/15 7:36:34.697 PM acvpnagent[51] Function: logInterfaces File: ../../vpn/AgentUtilities/Routing/InterfaceRouteMonitorCommon.cpp Line: 477 IP Address Interface List: FE80:0:0:0:224:1DFF:FE15:B69D 
9/16/15 7:36:34.000 PM kernel[0] in6_unlink_ifa: IPv6 address 0x6c5f3a5220436387 has no prefix
9/16/15 7:36:34.698 PM acwebsecagent[320] CMobileConnectorModule: IPAddr change event, wait 5000 milliseconds before actioning
9/16/15 7:36:34.698 PM acvpnagent[51] Function: getInterfaces File: ../../vpn/Common/Utility/NetInterface_unix.cpp Line: 1319 Invoked Function: ioctl SIOCGIFNETMASK_IN6 Return Code: 49 (0x00000031) Description: unknown errno=Can't assign requested address
9/16/15 7:36:34.698 PM acvpnagent[51] A network interface has gone down.
9/16/15 7:36:34.698 PM acvpnagent[51] Function: logInterfaces File: ../../vpn/AgentUtilities/Routing/InterfaceRouteMonitorCommon.cpp Line: 477 IP Address Interface List: 
9/16/15 7:36:34.699 PM acvpnagent[51] Function: applyHostConfigForNoVpn File: ../../vpn/Agent/MainThread.cpp Line: 9674 No network interface is available, cannot determine potential public addresses.
9/16/15 7:36:34.699 PM acvpnagent[51] Current network state: No network interface
9/16/15 7:36:34.699 PM acvpnagent[51] Function: applyHostConfigForNoVpn File: ../../vpn/Agent/MainThread.cpp Line: 9674 No network interface is available, cannot determine potential public addresses.
9/16/15 7:36:34.699 PM acwebsecagent[320] CMobileConnectorModule: IPAddr change event, wait 5000 milliseconds before actioning
9/16/15 7:36:34.700 PM acvpnagent[51] A new network interface has been detected.
9/16/15 7:36:34.700 PM acvpnagent[51] Function: logInterfaces File: ../../vpn/AgentUtilities/Routing/InterfaceRouteMonitorCommon.cpp Line: 477 IP Address Interface List: FE80:0:0:0:224:1DFF:FE15:B69D 
9/16/15 7:36:34.701 PM configd[55] LINKLOCAL en0: parent has no IP
9/16/15 7:36:34.710 PM configd[55] network changed: v4(en0-:192.168.1.107) DNS- Proxy-
9/16/15 7:36:35.110 PM netbiosd[863] network_reachability_changed : network is not reachable, netbiosd is shutting down
9/16/15 7:36:35.111 PM symptomsd[312] __73-[NetworkAnalyticsEngine observeValueForKeyPath:ofObject:change:context:]_block_invoke unexpected switch value 2
9/16/15 7:36:35.000 PM kernel[0] full wake promotion (reason 1) 2329 ms
9/16/15 7:36:35.330 PM acwebsecagent[320] WebsecSleepCallBack: messageType e0000320, arg 00000000
9/16/15 7:36:35.330 PM acwebsecagent[320] WebsecSleepCallBack: kIOMessageSystemWillPowerOn
9/16/15 7:36:35.000 PM kernel[0] Sound assertion in AppleHDAWidget at line 4284
9/16/15 7:36:35.000 PM kernel[0] Sound assertion in AppleHDACodecGeneric at line 1403
9/16/15 7:36:35.702 PM WindowServer[176] send_datagram_available_ping: pid 239 failed to act on a ping it dequeued before timing out.
9/16/15 7:36:35.702 PM WindowServer[176] handle_will_sleep_auth_and_shield_windows: NULL shield_window (lock state: 1)
9/16/15 7:36:35.703 PM WindowServer[176] CGXDisplayDidWakeNotification [1300305926749]: posting kCGSDisplayDidWake
9/16/15 7:36:35.707 PM acwebsecagent[320] CMobileConnectorModule: IPAddr change event, wait 5000 milliseconds before actioning
9/16/15 7:36:35.707 PM acvpnagent[51] A new network interface has been detected.
9/16/15 7:36:35.707 PM acvpnagent[51] Function: logInterfaces File: ../../vpn/AgentUtilities/Routing/InterfaceRouteMonitorCommon.cpp Line: 477 IP Address Interface List: FE80:0:0:0:224:1DFF:FE15:B69D 192.168.1.107 
9/16/15 7:36:35.718 PM configd[55] network changed: v4(en0+:192.168.1.107) DNS+ Proxy+ SMB
9/16/15 7:36:36.083 PM identityservicesd[382] <IMMacNotificationCenterManager: 0x7ffe12914970>: notification observer: com.apple.iChat   notification: __CFNotification 0x7ffe1070c850 {name = _NSDoNotDisturbDisabledNotification}
9/16/15 7:36:36.095 PM identityservicesd[382] <IMMacNotificationCenterManager: 0x7ffe12914970>:    NC Disabled: NO
9/16/15 7:36:36.100 PM identityservicesd[382] <IMMacNotificationCenterManager: 0x7ffe12914970>:   DND Enabled: NO
9/16/15 7:36:36.100 PM identityservicesd[382] <IMMacNotificationCenterManager: 0x7ffe12914970>: Updating enabled: YES   (Topics: (
    "com.apple.private.alloy.icloudpairing",
    "com.apple.private.alloy.continuity.encryption",
    "com.apple.private.alloy.continuity.activity",
    "com.apple.private.ids",
    "com.apple.private.alloy.phonecontinuity",
    "com.apple.private.alloy.phone.auth",
    "com.apple.private.alloy.keychainsync",
    "com.apple.private.alloy.fmf",
    "com.apple.private.alloy.screensharing",
    "com.apple.private.alloy.maps",
    "com.apple.private.alloy.thumper.keys",
    "com.apple.private.alloy.continuity.tethering"
))
9/16/15 7:36:36.202 PM symptomsd[312] __73-[NetworkAnalyticsEngine observeValueForKeyPath:ofObject:change:context:]_block_invoke unexpected switch value 2
9/16/15 7:36:38.000 PM kernel[0] en1: channel changed to 1
9/16/15 7:36:38.763 PM acwebsecagent[320] WebsecSleepCallBack: messageType e0000300, arg 00000000
9/16/15 7:36:38.763 PM acwebsecagent[320] WebsecSleepCallBack: kIOMessageSystemHasPoweredOn
9/16/15 7:36:40.530 PM ntpd[224] wake time set +1.185901 s
9/16/15 7:36:40.954 PM acvpnagent[51] Function: GetPrimaryInterfaceIndex File: ../../vpn/Common/Utility/NetInterface_unix.cpp Line: 408 Unable to get global IPv6 information from system configuration.
9/16/15 7:36:40.955 PM acvpnagent[51] Function: determinePublicAddrCandidateFromDefRoute File: ../../vpn/AgentUtilities/HostConfigMgr.cpp Line: 1766 Invoked Function: CHostConfigMgr::FindDefaultRouteInterface Return Code: -24117215 (0xFE900021) Description: ROUTETABLE_ERROR_GETBESTROUTE_FAILED 
9/16/15 7:36:40.955 PM acvpnagent[51] Function: updatePotentialPublicAddresses File: ../../vpn/AgentUtilities/HostConfigMgr.cpp Line: 1911 Invoked Function: CHostConfigMgr::determinePublicAddrCandidateFromDefRoute Return Code: -24117215 (0xFE900021) Description: ROUTETABLE_ERROR_GETBESTROUTE_FAILED 
9/16/15 7:36:40.955 PM acvpnagent[51] The client's public address is now set to 192.168.1.107
9/16/15 7:36:41.493 PM acvpnagent[51] Function: logProbeFailure File: ../../vpn/Agent/NetEnvironment.cpp Line: 1418 The HTTPS probe to 199.64.0.51 resulted in a redirect.
9/16/15 7:36:41.493 PM acvpnagent[51] Function: STLoadLibrary File: ../../vpn/Common/Utility/Win/HModuleMgr.cpp Line: 149 Invoked Function: dlopen Return Code: 0 (0x00000000) Description: dlopen(/Applications/Firefox.app/Contents/MacOS/libnss3.dylib, 1): Library not loaded: @executable_path/libmozglue.dylib   Referenced from: /Applications/Firefox.app/Contents/MacOS/libnss3.dylib   Reason: image not found 
9/16/15 7:36:41.493 PM acvpnagent[51] Function: loadLibs File: ../../vpn/CommonCrypt/Certificates/NSSCertUtils.cpp Line: 1453 Invoked Function: CHModuleMgr::STLoadLibrary Return Code: -33554425 (0xFE000007) Description: GLOBAL_ERROR_NOT_INITIALIZED Could not load: /Applications/Firefox.app/Contents/MacOS/libnss3.dylib
9/16/15 7:36:41.494 PM acvpnagent[51] Function: CNSSCertUtils File: ../../vpn/CommonCrypt/Certificates/NSSCertUtils.cpp Line: 330 Invoked Function: CNSSCertUtils::loadLibs Return Code: -33554425 (0xFE000007) Description: GLOBAL_ERROR_NOT_INITIALIZED 
9/16/15 7:36:41.494 PM acvpnagent[51] Function: CNSSCertStore File: ../../vpn/CommonCrypt/Certificates/NSSCertStore.cpp Line: 57 Invoked Function: CNSSCertUtils Return Code: -33554425 (0xFE000007) Description: GLOBAL_ERROR_NOT_INITIALIZED 
9/16/15 7:36:41.494 PM acvpnagent[51] Function: addNSSStore File: ../../vpn/CommonCrypt/Certificates/CollectiveCertStore.cpp Line: 1740 Invoked Function: CNSSCertStore::CNSSCertStore Return Code: -33554425 (0xFE000007) Description: GLOBAL_ERROR_NOT_INITIALIZED 
9/16/15 7:36:41.494 PM acvpnagent[51] Function: OpenStores File: ../../vpn/CommonCrypt/Certificates/CollectiveCertStore.cpp Line: 418 Invoked Function: CCollectiveCertStore::addNSSStore Return Code: -33554425 (0xFE000007) Description: GLOBAL_ERROR_NOT_INITIALIZED 
9/16/15 7:36:41.508 PM acvpnagent[51] Function: analyzeHttpResponse File: ../../vpn/Agent/NetEnvironment.cpp Line: 1602 SG (199.64.0.51) contacted
9/16/15 7:36:41.508 PM acvpnagent[51] Current network state: Secure Gateway accessible
9/16/15 7:36:41.510 PM acvpnagent[51] Function: GetPrimaryInterfaceIndex File: ../../vpn/Common/Utility/NetInterface_unix.cpp Line: 408 Unable to get global IPv6 information from system configuration.
9/16/15 7:36:41.511 PM acvpnagent[51] Function: determinePublicAddrCandidateFromDefRoute File: ../../vpn/AgentUtilities/HostConfigMgr.cpp Line: 1766 Invoked Function: CHostConfigMgr::FindDefaultRouteInterface Return Code: -24117215 (0xFE900021) Description: ROUTETABLE_ERROR_GETBESTROUTE_FAILED 
9/16/15 7:36:41.511 PM acvpnagent[51] Function: updatePotentialPublicAddresses File: ../../vpn/AgentUtilities/HostConfigMgr.cpp Line: 1911 Invoked Function: CHostConfigMgr::determinePublicAddrCandidateFromDefRoute Return Code: -24117215 (0xFE900021) Description: ROUTETABLE_ERROR_GETBESTROUTE_FAILED 
9/16/15 7:36:41.893 PM acwebsecagent[320] CMobileConnectorModule::TakeActionOnAddrChange
9/16/15 7:36:41.894 PM acwebsecagent[320] Got DNS suffix on address change: ''
9/16/15 7:36:41.894 PM acwebsecagent[320] TUpdater : Downloading tower details...
9/16/15 7:36:41.894 PM acwebsecagent[320] TUpdater : Downloading directly from tower
9/16/15 7:36:42.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:36:42.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:36:42.293 PM acwebsecagent[320] TUpdater : Downloading signed digest directly from tower
9/16/15 7:36:42.508 PM acwebsecagent[320] License : One or more of the License/Public Key can't be NULL
9/16/15 7:36:42.508 PM acwebsecagent[320] SSLExt : Failed to get ScanSafe headers
9/16/15 7:36:42.508 PM acwebsecagent[320] DownloadUpdatedConfig : Failed to download updated config. Host hostedconfig.scansafe.net. Code 0x80004005
9/16/15 7:36:42.716 PM acwebsecagent[320] TUpdater : got certfile: '/opt/cisco/anyconnect/websecurity/WebSecurityCert.cfg'
9/16/15 7:36:42.718 PM acwebsecagent[320] Error : Incorrect signature
9/16/15 7:36:42.718 PM acwebsecagent[320] TUpdater : DSA verify failed. Return: 0 Error: 168235011
9/16/15 7:36:42.718 PM acwebsecagent[320] TUpdater : Some error encountered in downloading tower details from the server. Code : 1000
9/16/15 7:36:49.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:36:49.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:36:56.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:36:56.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:37:04.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:37:04.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:37:11.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:37:11.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:37:16.669 PM WindowServer[176] send_datagram_available_ping: pid 239 failed to act on a ping it dequeued before timing out.
9/16/15 7:37:18.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:37:18.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:37:26.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:37:26.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:37:33.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:37:33.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:37:33.429 PM WindowServer[176] send_datagram_available_ping: pid 239 failed to act on a ping it dequeued before timing out.
9/16/15 7:37:40.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:37:40.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:37:42.718 PM acwebsecagent[320] TUpdater : Downloading tower details...
9/16/15 7:37:42.718 PM acwebsecagent[320] TUpdater : Downloading directly from tower
9/16/15 7:37:43.121 PM acwebsecagent[320] TUpdater : Downloading signed digest directly from tower
9/16/15 7:37:43.532 PM acwebsecagent[320] TUpdater : got certfile: '/opt/cisco/anyconnect/websecurity/WebSecurityCert.cfg'
9/16/15 7:37:43.534 PM acwebsecagent[320] Valid signature.  Digest and signature verification succeeded.
9/16/15 7:37:43.536 PM acwebsecagent[320] TUpdater : Tower details downloaded successfully
9/16/15 7:37:43.536 PM acwebsecagent[320] Tower Updater - Updating local tower details!!!!!!!!!!!!!!!!!!!!
9/16/15 7:37:43.536 PM acwebsecagent[320] Config: Current ActiveTowerHostName is being changed from 108.171.135.156 to 108.171.135.157
9/16/15 7:37:43.536 PM acwebsecagent[320] Config: ActiveTowerHostName has been changed to 108.171.135.157
9/16/15 7:37:43.541 PM acwebsecagent[320] TUpdater : Updated local tower details
9/16/15 7:37:43.542 PM acwebsecagent[320] CMobileConnectorModule::RunMessageLoop MSG_ID_TOWERS_UPDATED
9/16/15 7:37:43.542 PM acwebsecagent[320] Parse addr to cidr: ip is 108.171.128.157 and mask is 32
9/16/15 7:37:43.542 PM acwebsecagent[320] added exception: 9D80AB6C 32
9/16/15 7:37:43.542 PM acwebsecagent[320] Parse addr to cidr: ip is 108.171.129.157 and mask is 32
9/16/15 7:37:43.542 PM acwebsecagent[320] added exception: 9D81AB6C 32
9/16/15 7:37:43.542 PM acwebsecagent[320] Parse addr to cidr: ip is 80.254.150.78 and mask is 32
9/16/15 7:37:43.542 PM acwebsecagent[320] added exception: 4E96FE50 32
9/16/15 7:37:43.542 PM acwebsecagent[320] Parse addr to cidr: ip is 80.254.154.98 and mask is 32
9/16/15 7:37:43.542 PM acwebsecagent[320] added exception: 629AFE50 32
9/16/15 7:37:43.542 PM acwebsecagent[320] Parse addr to cidr: ip is 80.254.155.66 and mask is 32
9/16/15 7:37:43.542 PM acwebsecagent[320] added exception: 429BFE50 32
9/16/15 7:37:43.542 PM acwebsecagent[320] Parse addr to cidr: ip is 196.26.220.66 and mask is 32
9/16/15 7:37:43.542 PM acwebsecagent[320] added exception: 42DC1AC4 32
9/16/15 7:37:43.543 PM acwebsecagent[320] Parse addr to cidr: ip is 201.94.155.66 and mask is 32
9/16/15 7:37:43.543 PM acwebsecagent[320] added exception: 429B5EC9 32
9/16/15 7:37:43.543 PM acwebsecagent[320] Parse addr to cidr: ip is 184.150.236.58 and mask is 32
9/16/15 7:37:43.543 PM acwebsecagent[320] added exception: 3AEC96B8 32
9/16/15 7:37:43.543 PM acwebsecagent[320] Parse addr to cidr: ip is 69.10.152.66 and mask is 32
9/16/15 7:37:43.543 PM acwebsecagent[320] added exception: 42980A45 32
9/16/15 7:37:43.543 PM acwebsecagent[320] Parse addr to cidr: ip is 108.171.135.157 and mask is 32
9/16/15 7:37:43.543 PM acwebsecagent[320] added exception: 9D87AB6C 32
9/16/15 7:37:43.543 PM acwebsecagent[320] Parse addr to cidr: ip is 108.171.130.157 and mask is 32
9/16/15 7:37:43.543 PM acwebsecagent[320] added exception: 9D82AB6C 32
9/16/15 7:37:43.543 PM acwebsecagent[320] Parse addr to cidr: ip is 108.171.131.156 and mask is 32
9/16/15 7:37:43.543 PM acwebsecagent[320] added exception: 9C83AB6C 32
9/16/15 7:37:43.543 PM acwebsecagent[320] Parse addr to cidr: ip is 108.171.132.157 and mask is 32
9/16/15 7:37:43.543 PM acwebsecagent[320] added exception: 9D84AB6C 32
9/16/15 7:37:43.543 PM acwebsecagent[320] Parse addr to cidr: ip is 69.174.87.131 and mask is 32
9/16/15 7:37:43.543 PM acwebsecagent[320] added exception: 8357AE45 32
9/16/15 7:37:43.543 PM acwebsecagent[320] Parse addr to cidr: ip is 202.167.250.90 and mask is 32
9/16/15 7:37:43.543 PM acwebsecagent[320] added exception: 5AFAA7CA 32
9/16/15 7:37:43.544 PM acwebsecagent[320] Parse addr to cidr: ip is 108.171.159.46 and mask is 32
9/16/15 7:37:43.544 PM acwebsecagent[320] added exception: 2E9FAB6C 32
9/16/15 7:37:43.544 PM acwebsecagent[320] Parse addr to cidr: ip is 122.50.127.66 and mask is 32
9/16/15 7:37:43.544 PM acwebsecagent[320] added exception: 427F327A 32
9/16/15 7:37:43.544 PM acwebsecagent[320] Parse addr to cidr: ip is 202.79.203.110 and mask is 32
9/16/15 7:37:43.544 PM acwebsecagent[320] added exception: 6ECB4FCA 32
9/16/15 7:37:43.544 PM acwebsecagent[320] Parse addr to cidr: ip is 108.171.134.157 and mask is 32
9/16/15 7:37:43.544 PM acwebsecagent[320] added exception: 9D86AB6C 32
9/16/15 7:37:43.544 PM acwebsecagent[320] Parse addr to cidr: ip is 1.1.1.1 and mask is 32
9/16/15 7:37:43.544 PM acwebsecagent[320] added exception: 1010101 32
9/16/15 7:37:43.544 PM acwebsecagent[320] Parse addr to cidr: ip is 65.55.10.11 and mask is 32
9/16/15 7:37:43.544 PM acwebsecagent[320] added exception: B0A3741 32
9/16/15 7:37:43.544 PM acwebsecagent[320] Parse addr to cidr: ip is 10.86.95.246 and mask is 32
9/16/15 7:37:43.544 PM acwebsecagent[320] added exception: F65F560A 32
9/16/15 7:37:43.544 PM acwebsecagent[320] Parse addr to cidr: ip is 80.254.145.118 and mask is 32
9/16/15 7:37:43.544 PM acwebsecagent[320] added exception: 7691FE50 32
9/16/15 7:37:43.544 PM acwebsecagent[320] after init_redirect: Redirecting port 80 to port 5001
9/16/15 7:37:43.545 PM acwebsecagent[320] after init_redirect: Redirecting port 8080 to port 5001
9/16/15 7:37:43.545 PM acwebsecagent[320] after init_redirect: Redirecting port 3128 to port 5001
9/16/15 7:37:43.545 PM acwebsecagent[320] redirectInfoList iteration: op=2 peerport=80 redirectport=5001
9/16/15 7:37:43.545 PM acwebsecagent[320] redirectInfoList iteration: op=2 peerport=80 redirectport=5001
9/16/15 7:37:43.545 PM acwebsecagent[320] redirectInfoList iteration: op=2 peerport=80 redirectport=5001
9/16/15 7:37:43.545 PM acwebsecagent[320] redirectInfoList iteration: op=2 peerport=8080 redirectport=5001
9/16/15 7:37:43.545 PM acwebsecagent[320] redirectInfoList iteration: op=2 peerport=8080 redirectport=5001
9/16/15 7:37:43.545 PM acwebsecagent[320] redirectInfoList iteration: op=2 peerport=8080 redirectport=5001
9/16/15 7:37:43.545 PM acwebsecagent[320] redirectInfoList iteration: op=2 peerport=3128 redirectport=5001
9/16/15 7:37:43.545 PM acwebsecagent[320] redirectInfoList iteration: op=2 peerport=3128 redirectport=5001
9/16/15 7:37:43.545 PM acwebsecagent[320] redirectInfoList iteration: op=2 peerport=3128 redirectport=5001
9/16/15 7:37:43.545 PM acwebsecagent[320] redirectInfoList iteration: op=1 peerport=0 redirectport=0
9/16/15 7:37:43.545 PM acwebsecagent[320] redirectInfoList iteration: op=1 peerport=0 redirectport=0
9/16/15 7:37:43.545 PM acwebsecagent[320] SetRedirects returned 0
9/16/15 7:37:43.545 PM acwebsecagent[320] SocketRedirectorApi->Start success
9/16/15 7:37:43.545 PM acwebsecagent[320] <==InitialiseRedirectorInterface
9/16/15 7:37:43.545 PM acwebsecagent[320] GetSortedTowers found g_pDetectClosestTower NULL
9/16/15 7:37:43.546 PM acwebsecagent[320] GetSortedTowers : get towers from config...
9/16/15 7:37:43.546 PM acwebsecagent[320] MSG_ID_TOWERS_UPDATED.. send to plugin: 'UK,Germany,France,Denmark,Switzerland,South Africa,Brazil,Canada East Coast,Canada West Coast,US West Coast,US East Coast,US Midwest,US South,US Southeast,Hong Kong,India,Japan,Singapore,Australia&US West Coast'
9/16/15 7:37:47.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:37:47.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:37:55.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:37:55.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:38:02.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:38:02.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:38:09.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:38:09.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:38:17.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:38:17.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
9/16/15 7:38:24.000 PM kernel[0] Sound assertion in AppleHDADriver at line 5761
9/16/15 7:38:24.000 PM kernel[0] Sound assertion in AppleHDADriver at line 676
Edited by jrhende
Link to comment
Share on other sites
jrhende
jrhende
Posted
Posted

Activity monitor (energy tab) is fine. However, pmset -g assertions shows

pmset -g assertions
2015-09-17 17:57:13 -0700
Assertion status system-wide:
BackgroundTask 1
ApplePushServiceTask 0
UserIsActive 0
PreventUserIdleDisplaySleep 0
PreventSystemSleep 0
ExternalMedia 0
PreventUserIdleSystemSleep 0
NetworkClientActive 0
Listed by owning process:
pid 46(UserEventAgent): [0x0000000e000b014f] 00:04:19 BackgroundTask named: "com.apple.mds.1"
Created for PID: 64.
pid 46(UserEventAgent): [0x0000000e000b014e] 00:04:19 BackgroundTask named: "com.apple.mds.2"
Created for PID: 64.
pid 46(UserEventAgent): [0x0000000d000b0148] 00:04:20 BackgroundTask named: "com.apple.mds.0"
Created for PID: 64.
pid 46(UserEventAgent): [0x00000008000b013f] 00:04:25 BackgroundTask named: "com.apple.metadata.mds.power"
Created for PID: 64.
Kernel Assertions: 0x4=USB
id=500 level=255 0x4=USB mod=12/31/69, 5:00 PM description=com.apple.usb.externaldevice.fa100000 owner=IOUSBHostDevice
id=501 level=255 0x4=USB mod=12/31/69, 5:00 PM description=com.apple.usb.externaldevice.fa110000 owner=USB 2.0 Hub
id=502 level=255 0x4=USB mod=12/31/69, 5:00 PM description=com.apple.usb.externaldevice.fa120000 owner=USB Keyboard
id=503 level=255 0x4=USB mod=12/31/69, 5:00 PM description=com.apple.usb.externaldevice.fa112000 owner=Logitech USB Optical Mouse
Idle sleep preventers: IODisplayWrangler

any ideas?

Link to comment
Share on other sites
VirusX
VirusX
Posted
Posted

 

 

9/16/15 7:36:33.000 PM kernel[0] Wake reason: RTC USB0 (Alarm)

I suspect that your USB hub is causing the wake up. Or another USB device (USB0). Try to find out which one it is. 

http://www.insanelymac.com/forum/topic/300072-wake-reason-rtc-alarm-how-to-deactivate/ that thread might also be interesting to read for you since it is also and RTC alarm.

 

My USB bluetooth dongle wakes my computer up too. But interestingly, I found out that the computer tries to go back to sleep immediately afterwards again and that time it works.

I put my computer to sleep, it wakes up again because of bluetooth, I do nothing and after a few seconds, it goes back to sleep and stays put ;) So maybe wait a few seconds too?

 

edit: oh wait... what I described was in yosemite... Haven't tested El Capitan thoroughly enough to say if it's the same there...

Link to comment
Share on other sites
nabziF99
nabziF99
Posted
Posted (edited)

Preface: My board is EX58-UD5, F12 BIOS.

 

 

I thought it might help to write down all the steps again for the final Yosemite version..

 

Step by Step Guide for Yosemite on our EX58-UD5 and Clover

 

.

.

.

4) boot from clover usb drive and select yosemite usb installer. Follow through the steps and install yosemite on your hard drive

5) boot from clover usb drive and select hard drive with the installed yosemite.

6) add/apply toleda's audio patch to clover's config and run his script. We have audio codec 885 (which equals to 889a)

DONE

 

I know it's been awhile since these nice and concise steps were posted, but I'm stuck at step 6. The link points to CloverALC, so I downloaded it (audio_CloverALC-master.zip), proceeded with the instructions there (i.e. "Double click: Downloads/audio_cloverALC-110.command"), and got this:

File: audio_cloverALC-110.command_v1.0f
EFI partition is not mounted
Confirm Clover Legacy Install (y/n): y
/Volumes/[path]/audio_CloverALC-master/audio_cloverALC-110_v1.0f.command: line 318: [: /Volumes/[Yosemite drive]: binary operator expected
/Volumes/[Yosemite drive]/EFI/CLOVER not found
No system files were changed 

(portions enclosed in brackets are unique to my system so I've redacted them)

 

I figured maybe this meant I was supposed to first mount the USB drive's EFI partition even though that wasn't mentioned in the guide. So I did so, but that appears to be empty. I wasn't too surprised, because when I followed step 1 to create a USB installer, google led me here, and following the steps there appears to have installed Clover into a folder named "EFI" on the USB's main partition rather than in its EFI partition - and somehow it boots. Nevertheless, after mounting that EFI partition I ran toleda's script again, and predictably got the same error. So then I ejected that EFI, and instead mounted my Yosemite hard drive's EFI partition. It didn't yet have Clover (installing Clover to the Yosemite hard drive isn't mentioned until step 7), so that too was futile.

 

So I thought maybe what the script is looking for is Clover installed in the Yosemite hard drive. So I did that (thereby skipping step 6). I rebooted, mounted the Yosemite hard drive's EFI partition, went back to try step 6 again, and get this:

EFI partition is mounted
Boot/Arguments = kext-dev-mode=1 found
Error: no IOReg/HDEF; BIOS/audio/disabled or ACPI problem
No system files were changed

I googled that error, and all relevant hits seem to point here. I followed those troubleshooting steps which led me to add HDEF...at which point I stopped, thinking I must have made a wrong turn much earlier, otherwise VirusX would have mentioned all this. Step 6 sounded so much simpler...

 

So I'm guessing there are two possibilities here: either I took a wrong turn on step 1 (i.e. I should have created the install USB based on some other guide than the ##### one due to the way it installed Clover I mentioned above)...or toleda has modified his script so much since VirusX's post that I'm missing some additional steps somewhere.

 

Has anyone followed VirusX's steps lately using current versions (Yosemite 10.10.5, Clover v2.3k r3270, audio_cloverALC-110)? If so, have you encountered errors like the ones I've listed, and have an idea as to what I'm missing? (maybe I just need to proceed with taleda's troubleshooting steps?)

 

Thanks!

Edited by Micky1979
read the rule plaese
Link to comment
Share on other sites
@ROBASEFR
@ROBASEFR
Posted
Posted

USB Installers don't have EFI in ESP !

They have the EFI folder in the same place as the App and System folder.

 

But you don't need audio configuration in the install process !

 

For the audio configuration:

As the name suggests "audio_cloverALC-110.command" is for Clover boot only !

 

That command ads patches in the config.plist in the partition 0 of your disk:(ie)   \EFI\CLOVER and only if this EFI partition is mounted and visible on your desktop !

 

I saw that you found that! Ok

 

Your error message suggests:  that you have to modify your bios to have HDEF support. (Azalia in the BIOS) and or you have to use an appropriate DSDT /SSDT for your MOBO !

 

EFI partition is mounted
Boot/Arguments = kext-dev-mode=1 found
Error: no IOReg/HDEF; BIOS/audio/disabled or ACPI problem
No system files were changed

 

 

I suggest you try this DSDT first from dood

 

http://www.insanelymac.com/forum/topic/196771-ga-ex58-and-ga-x58a-dsdt-native-power-management-modifications/

DSDT_GA_EX58_UD5_F9m_S3_v6.zip

 

If you use Clover put it in : EFI/CLOVER/ACPI/patched

 

Success !

Link to comment
Share on other sites
jrhende
jrhende
Posted
Posted

Loaded latest official 10.11.  Still have sleep problems.  Note that could not get kexts to load from 10.11 or Others.  Used a kext installer tool to install kexts like AppleHDA to get my audio to work.  The tool must be placing them in S/L/E or the equivalent.  Rather use the former method but gave up.  Was able to upgrade 10.10 to 10.11 and keep all my applications and etc. 

Link to comment
Share on other sites
jrhende
jrhende
Posted
Posted

Solved it.  Narrowed down the issue where on sleep the system would immediately wake up.  Removed USB Bluetooth DBT-122 and system would sleep.  Didn't want to have to manually remove the DBT-122 every time needing to go to sleep (not desirable for auto sleep) so I used the kexts from 10.10.5 which were IOBluetoothFamily and IOBluetoothHIDDriver and the system can sleep and wake fine (two tests successful so far).  Identifying the appropriate kexts was determined empirically.  No apparent loss of functionality observed.  Therefore, the transition to El Capitan is complete.

 

This will be the last OS X version on the trusty EX58-EXTREME cross flashed to EX58-UD5.

 

Not using any DSDT.aml and the config.plist is vanilla except for a few cosmetic tweaks taken from @ROBASEFR.

 

Thanks VirusX for your help.   

  • Like 1
Link to comment
Share on other sites
nabziF99
nabziF99
Posted
Posted

Thanks for the reply Robasefr! Just a couple clarifications:

 

USB Installers don't have EFI in ESP !

They have the EFI folder in the same place as the App and System folder.

 

But you don't need audio configuration in the install process !

Ah, so VirusX's step 7 (install clover to hard drive) should have come before step 6 (apply audio patch)?

 

 

Your error message suggests:  that you have to modify your bios to have HDEF support. (Azalia in the BIOS) and or you have to use an appropriate DSDT /SSDT for your MOBO !

...

I suggest you try this DSDT first from dood

Oh...I had thought since I have the same board as VirusX (GA-EX58-UD5) that I could simply use his steps and not need a DSDT, as per his earlier post:

 

 

I don't have a custom DSDT in my clover folder (like ROBASEFR has). Everything I need to be patched (orange icons, SSD trim, CMOS reset, Graphic inject), is inserted/created by Clover while booting.

...so does this sound like VirusX already modified his BIOS to have HDEF support and just forgot to mention it?

Link to comment
Share on other sites
iCore
iCore
Posted
Posted

Moved from Yosemite via El Capitan DP1->Dp8 and GM to 10.11. :D Now with latest Clover r3280

 

Changed also my old faithfull HD 4850 for an GTX970 Phantom

 

(apart from USB3 everything is OK.)

 

Here is my latest config.plist

attachicon.gifconfig.zip

 

Cheers

 

Could you share your Clover kext configuration ?

(I guess your DSDT is the  DSDT_GA_EX58_UD5_F9m_S3_v6 you shared few posts ago)

 

With my EX58-UD5/Bios F13/Clover/Yosemite 10.10.4 I have an issue with the sleep/power off.

- Sleep does not work: machine goes to sleep but crashes (sometimes with a BIOS reset/corruption*) at wakeup

- Power off does not work half of the time (everything goes fine, I get the "CPU Halted" message, but system fans never stop)

 

Here is my CLOVER/kexts/10.10 content:

- AppleRTC.kext

- FakeSMC.kext

- NullCPUPowerManagement.kext

- RealtekRTL81xx.kext

- VoodooHDA.kext

 

I will try the clover config you shared, but before I would like to be sure I don't miss (or have useless) kexts.

 

Thanks

 

*: The BIOS corruption leads to the following behavior at startup: 

When I press the power button, the motherboard starts (internal leds light up, all fans start) and after less than a second, everything stops.

And then it restarts again... and stops again after a second, and so forth...

Symptoms look like an hardware issue, but clearing CMOS with the "Clr CMOS" switch solves it.

Link to comment
Share on other sites
@ROBASEFR
@ROBASEFR
Posted
Posted

Could you share your Clover kext configuration ?

(I guess your DSDT is the  DSDT_GA_EX58_UD5_F9m_S3_v6 you shared few posts ago)  YES

 

With my EX58-UD5/Bios F13/Clover/Yosemite 10.10.4 I have an issue with the sleep/power off.

- Sleep does not work: machine goes to sleep but crashes (sometimes with a BIOS reset/corruption*) at wakeup (Sleep works 100%)

- Power off does not work half of the time (everything goes fine, I get the "CPU Halted" message, but system fans never stop)

 

Here is my CLOVER/kexts/10.10 content:

- AppleRTC.kext (no need, because you activate it in clover config/Kernel and kext patches  )

- FakeSMC.kext (I have version 6.18.1394) with plugins)

- NullCPUPowerManagement.kext ( I never used this !)

- RealtekRTL81xx.kext ( I use v2.0 RealtekRTL8111.kext)

- VoodooHDA.kext ( i don't use it because of using patches from Toleda (audio_cloverALC-110.sh version v.1.0 f ) ! )

-AHCIPortInjector.kext

-ApplePCIIDE.kext v.1.03 (for my old ATA DVD burner !)

 

I will try the clover config you shared, but before I would like to be sure I don't miss (or have useless) kexts.

 

Thanks

 

*: The BIOS corruption leads to the following behavior at startup: 

When I press the power button, the motherboard starts (internal leds light up, all fans start) and after less than a second, everything stops.

And then it restarts again... and stops again after a second, and so forth...

Symptoms look like an hardware issue, but clearing CMOS with the "Clr CMOS" switch solves it.

Updated !

I have put my comments in red.

For your Nvidia graphic card ,  Install the latest webdrivers 346.03.02f02 once you have installed OSX.

Install OSX with nv_disable=1  in / Boot and put  after webdriver install  nvda_drv=1  then reboot  !

 

Good luck

  • Like 1
Link to comment
Share on other sites
VirusX
VirusX
Posted
Posted

sorry for my late reply - haven't been around here in a while.

or toleda has modified his script so much since VirusX's post that I'm missing some additional steps somewhere.

yes that is indeed correct. He basically rewrote the script from scratch. Now the script looks up which codec you need etc automatically. More comfortable for most users I guess.

The standard installation method in now on the EFI partition. Advantage: it survives any software updates. Disadvantage: usb installs don't have an EFI partition.

 

Ah, so VirusX's step 7 (install clover to hard drive) should have come before step 6 (apply audio patch)?

 

...so does this sound like VirusX already modified his BIOS to have HDEF support and just forgot to mention it?

yes, for toleda's patch to work, clover now has to be installed first onto the hard drive.

I have never modified HDEF in BIOS - that's why I didn't mention it ;)

 

As far as I remember from my El Capitan test install on a spare partition, toleda's new script can also patch the AppleHDA. I don't recall what selections I made during the run of his script but it worked... But as soon as I update El Capitan, patch needs to be reapplied.

 

If your system works fine besides the sound, install clover to your hard drive in the EFI partition, apply the patch (install in EFI partition) and you should be fine :)

 

Good luck

Link to comment
Share on other sites
iCore
iCore
Posted
Posted

Updated !

I have put my comments in red.

For your Nvidia graphic card ,  Install the latest webdrivers 346.03.02f02 once you have installed OSX.

Install OSX with nv_disable=1  in / Boot and put  after webdriver install  nvda_drv=1  then reboot  !

 

Good luck

 

Thanks for your comments, it was cristal clear. 

 

I followed your "instructions" and change my Clover configuration accordingly (replacing my DSDT and config with yours, and using the kexts you mentionned).

The only things I didn't do, was to put the ApplePCIIDE (as I don't have any IDE device).

and I did not follow you nvidia instructions, as my GTX660 is not handled by nvdia drivers (only GTX680 is).

Instead I used the NVCAP string I was already using in my config.plist

 

So the Graphics key looks like this (in case it may help people having the same graphic card: MSI N660 Gaming 2GB/OC TwinFrozr )

 

<key>Graphics</key>
<dict>
  <key>Inject</key>
  <dict>
    <key>ATI</key>
    <false/>
    <key>Intel</key>
    <false/>
    <key>NVidia</key>
    <false/>
  </dict>
  <key>NvidiaSingle</key>
  <false/>
  <key>NVCAP</key>
  <string>050000000000FFFFFFFF00000000000E00000000</string>
</dict>
It works perfectly, with 2 screens: one is plugged in DVI, the second which is 4K using display port

 

I also kept the VoodooHDA kext, until I investigate the toleda patch thing.

 

Anyway, everything seems to works perfectly (sleep, poweroff, network, ...)

 

Thank you very much.

  • Like 1
Link to comment
Share on other sites
minomus
minomus
Posted
Posted

I hope this question is okay to ask here, since the topic regarding the script for Snow Leopard links here.

My situation is that I have had a Hackintosh for music producing since 2010, installed using digital_dreamers script. After unsuccessful .kext installation the OS went useless. There are tons of reasons I have not updated it further than 10.6.3 and I'd like to keep it that way. It's been many years since I built the machine, so I've lost a bit the touch when it comes to Hackintosh things and probably some things have changed.

First of all, my rig:

Gigabyte GA-EX58-UD5
Intel i7 920

8gb RAM
ATI Radeon HD 4830 dual-dvi

OSX 10.6.3 (hopefully could keep it that way)

Especially because of the graphics card, it was quite a mess to get working in first place. Doing a clean install is something i'd like to avoid if possible, as it would require days worth of installing to get back to my works in progress.

So, I booted from USB installation stick, restored partition where Hackintosh was installed using Snow Leopard installer's restore/Time Machine. I've tried several ways to continue from there after managing to boot in safe mode, but always ended up with kernel panics of many kinds and therefore restoring again. Maybe it's worty to mention that I also ended up changing the installation partition to another one of two HDDs.

While waiting for restore to complete again, my question is what should I do after the Hackintosh partition is restored? Is just running kext enabler in first safe boot enough? Am I correct assuming that restored (week old) partition should have right kexts and also right DSDT.aml in right places already? Or maybe only install the bootloader again using the script? Please help, I've wasted couple of days here already :D

Another question is does anybody still have netkas Exotic patch 10.6.3 still somewhere? Can't find any mirrors as the original source is down and can't get ##### pkg opened (i think it contains it, but I don't want to mix things up with using ##### on recovered unclean install.)

Link to comment
Share on other sites
@ROBASEFR
@ROBASEFR
Posted
Posted

Hello,

I asume your old rig used Chameleon bootloader ?

I moved for a while now on Clover, so you have to look elsewhere if you stay with that....

 

First of all your rig should work well with latest 10.11.1 !

 

Latest QE/CI patch for your graphic card from fantomas1 is here http://www.insanelymac.com/forum/files/file/415-qe-ci-exotic-patch/

An old Exotic patch for 10.6.8 is attached

 

You could going on with the USB stick as bootunit meanwhile you fiddleup your old configuration

 

If you decide to move to Yosemite or El Capitan with Clover Bootloader I can strongly advise you to use the install USB method from Chris1111   here :http://www.insanelymac.com/forum/files/file/471-clover-v23k-special-edition-v2/

His site is here with tutos and a lot more (but in french) ! http://www.hackintosh-montreal.com/

 

 

1427-QE_CI_Exotic patch for 10.6.8.zip.zip

 

Good luck

Link to comment
Share on other sites
  • 1 month later...
nabziF99
nabziF99
Posted
Posted

sorry for my late reply - haven't been around here in a while.

yes that is indeed correct. He basically rewrote the script from scratch. Now the script looks up which codec you need etc automatically. More comfortable for most users I guess.

The standard installation method in now on the EFI partition. Advantage: it survives any software updates. Disadvantage: usb installs don't have an EFI partition.

 

yes, for toleda's patch to work, clover now has to be installed first onto the hard drive.

I have never modified HDEF in BIOS - that's why I didn't mention it ;)

 

As far as I remember from my El Capitan test install on a spare partition, toleda's new script can also patch the AppleHDA. I don't recall what selections I made during the run of his script but it worked... But as soon as I update El Capitan, patch needs to be reapplied.

 

If your system works fine besides the sound, install clover to your hard drive in the EFI partition, apply the patch (install in EFI partition) and you should be fine :)

 

Good luck

 

VirusX, thanks for the response! However I'm still stuck; I installed Clover on the hard drive, it seems to boot ok (though it would spontaneously reboot itself until I added NullCPUPowerManagement.kext). But I'm still getting the error from my previous post when running audio_cloverALC-110_v1.0f.command:

EFI partition is mounted
Boot/Arguments = kext-dev-mode=1 found
Error: no IOReg/HDEF; BIOS/audio/disabled or ACPI problem
No system files were changed

Did I miss something? The only thing in my BIOS settings I see regarding audio is Integrated Peripherals->Azalia Codec->Auto...does that sound right?

 

Toleda's troubleshooting guide leads to more steps that you didn't mention (stuff about adding HDEF, dsdt, ssdt, etc), that seems to have a dead end, so I figured maybe it's something wonky in the Clover config.plist I'm using. So I replaced it with the fresh vanilla config.plist the Clover installer created, rebooted, ran cloverALC, and now get this:

EFI partition is mounted
Boot/Arguments = kext-dev-mode=1 found

No audio codec detected

Toleda's troubleshooting guide sends me to the same place for this - adding HDEF, but then a dead end.

 

Since our boards are basically identical, I'm hoping there's a simple step I'm missing that you might know about.

Any ideas are appreciated. Thanks!

 

<edited to abide by a forum rule I missed earlier>

Link to comment
Share on other sites
nabziF99
nabziF99
Posted
Posted

I'm hoping there's a simple step I'm missing

 

Update: success! Indeed the problem was relatively simple: Clover's config.plist was a "mess", wreaking havoc with toleda's script, as he pointed out. Changing config.plist/Devices/Audio/#Inject/0x0887 to config.plist/Devices/Audio/Inject/1 allowed the script to work its magic.

 

(Apparently pound signs are used to comment lines out, and Clover's default config starts out with basically everything commented out. Not sure what's with the default value of 0x0887, but that's a question for another place.)

Link to comment
Share on other sites
  • 2 weeks later...
jrhende
jrhende
Posted
Posted

Thanks to @ROBASEFR

 

After upgrading to 10.11.2 noticed CMOS reset problem again.  The perl script mechanism to patch my AppleRTC kext didn't fix it this time.  (I have read that that patch makes the code jump over the call to reset the CMOS.)  Took the ACPI section from his config.plist and put back the d00d DSDT.aml and problem gone.  Not sure which thing did it.  The problem manifests itself by not fully waking from sleep and my motherboard error code displays CF meaning a CMOS checksum error.

 

I'm standing up a new Hack using an MSI X99S AC XPOWER i7 5820K.  The old EX58 is being regulated to be the family computer.

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing
×
×
  • Create New...