1619 replies to this topic

[rayap]

With Chameleon-2.2svn-r2140, me too can only boot with -f
Looks like the extensions in /E/E do not load otherwise.

[ErmaC]

Install also the KernelPatcher.dylib module in Extra/modules.

Fabio

[mlstudio]

ErmaC, on 26 December 2012 - 11:48 AM, said:

Install also the KernelPatcher.dylib module in Extra/modules.

Fabio

THANKS FABIO ! Working now !

[mitch_de]

ErmaC, on 26 December 2012 - 11:48 AM, said:

Install also the KernelPatcher.dylib module in Extra/modules.

Fabio

Would be nice to get some infos about what module is needed and for what.
I use newer chameleon builds but never installed any of the modules in modules folder (for me its empty).
I use also C2D.

[rayap]

ErmaC, on 26 December 2012 - 11:48 AM, said:

Install also the KernelPatcher.dylib module in Extra/modules.

Fabio

Works but appear not to load patched AppleRTC.kext from /E/E only from /S/L/E.
Thanks anyway.

[meklort]

rayap, on 27 December 2012 - 02:03 PM, said:

Works but appear not to load patched AppleRTC.kext from /E/E only from /S/L/E.

If AppleRTC is already in /S/L/E, the kernel will always use the one in the prelinked kernel.

[juanerson]

Hi rayap. In Mountain Lion 10.8 (also Lion 10.7) none extension will not load from /E/E using "UseKernelCache=Yes" which is the option by default (to bring fast boot). But it works with "UKC=No" (slow boot), because those OS X versions have kernelcache (prelinked kernel) instead of Extensions.mkext (Snow Leopard 10.6). Regards.

[rayap]

Thanks Guys. Previously revisions no issues, with patched AppleRTC in /E/E and retained vanilla AppleRTC in /S/L/E. Now resolved with r2140 by including KernelPatcher.dylib and deleting vanilla AppleRTC from S/L/E. Have never set "UseKernelCache" either way. Trying to keep S/L/E vanilla except for AppleHDA.

[rvxtm]

My question is : do you still have to use "UseKernelCache=1" or is it default enabled even if i use the kernel patcher module for /e/e ?

[juanerson]

Just for record, "UseKernelCache=Yes" is the default option in Chameleon 2.1 and 2.2 svn.

[plsh2me]

With latest 2140 2.2svn my system goes on kp
 2013-01-02_20-46-41.jpg   727.41K   81 downloads

System description on signature.

Thanks
Palash

[juanerson]

Hi plsh2me. There is nothing to do about Chameleon 2.2svn, you need a NULLCpuPowerManagement.kext (to pass the 0xE2 MSR registers in Sandy Bridge CPUs) until patching the AICPUPM.kext (using AICPMPatch), and also is recommended to fix your DSDT or SSDT table of P-States (see this topic for more information). Another recommendation, please forget about using .kexts from /E/E, just install it all them in /S/L/E and set "UseKernelCache=Yes". Good Luck.

[k3nny]

Hi, compiled r2152 from voodooprojects to test the HD4000 in 10.8.3 but it hangs during the injection.
Tried dirrefent iGPU RAM settings from 32-96MB in combination with Virtu MPV setting which just seems to power on the iGPU when the dedicated card is selected. No success yet.
HD4000: PCI\VEN_8086&DEV_0162&SUBSYS_84CA1043&REV_09

One more thing. r2152 shows a huge log scanning each extension in /S/L/E which lasts about one minute.
Is there a setting to turn off this behavior?

[oswaldini]

If i use "-v ncpi=0x2000 dart=0" at boot from command prompt everything is OK but when I put this in org.chameleon.Boot.plist loading stopped. With clean section Kernel Flags in org.chameleon.Boot.plist everything is OK.

Enoch 2151 and regular trunk 2153 has the same issue.
I report that issue at http://forge.voodoop...eon/issues/314/

[Alex Auditore]

Is it posible to wake my computer with a mouse or keyboard if I use Chamelion?

[oswaldini]

Yes if you are using USB, you must set it in BIOS. I don't know how it works with PS2

[rvxtm]

One question, i use RealtekRTL81xx.kext (macman's realtek driver) , if i put it in s/l/e , it loads ok, but if i put it in e/e , it does not load at all, and yes, i use the kernelpatcher plugins for chameleon. FakeSMC loads, my audio driver loads and my sata driver loads ok, only the realtek kext refuses to load.

Is this behaviour normal ? i need to use it in e/e to use the internet for the first boot, without the need to boot into another OSX partition and move it to s/l/e.

Thanks.

[vantin1992]

Hi there, do we still need to disable Fast Startup for Windows 8 with the new Chameleon when triple boot with Mountain Lion and Ubuntu on Hybrid GPT/MBR disk?

[theconnactic]

Hello, folks!

I've been trying to make the boot screen (that gray one that has the Apple logotype with the spinning pinwheel right bellow it) to appear with the correct resolution - not the annoying stretched one, in some cases smaller than the screen resulting in an ugly black frame around the screen - but any of my attempts ended in failure. I use graphics cards that are otherwise fully working: respectively, an Ion nVidia, a G210 and a 9800 GT. How can i get them to recognize and put to the proper resolution the boot screen?

Another related question: how can i use the boot screen that's used by real macs and also by clover? It's slightly different from the one given by the "legacy logo" option because it has a bas-relief effect on the dark-gray Apple logo. I suppose it's inside boot.efi, since clover can use it, but i cannot access it and, even if i could, i wouldn't know how to put it in chameleon.

Thank you very much.

[gothic860]

enoch i386 folder link is broken on 1 page.

EDIT: Fixed or i made a mistake. Thanks anyway .