Jump to content

AppleVIAATA over 4gb RAM bug solved (at least i believe so)! JMicron and AppleNForceATA at development


  • Please log in to reply
569 replies to this topic

#101
slashack

slashack

    InsanelyMac Geek

  • Members
  • PipPipPipPip
  • 203 posts
  • Gender:Male
  • Location:Buenos Aires, Argentina

Hi,
I Use AHCI for the internal one:

On ATA Bus is just my DVDRW:

When I put your latest j-micronata two new ATA Bus are showed in system profiler, one of them populate with my EATA hdd, and the warning "AppleIntelPIIXPATA: Secondary PCI IDE channel is disabled" is gone, but I got another one "JMicronATA 4 bytes not aligned"
With appleviaata I got a new entry on Serial-ATA section with my EATA hdd on it.

Dunno if helps but here is my EATA entry from DSDT:

Device (EATA)                {                    Name (_ADR, Zero)                    OperationRegion (SATE, PCI_Config, Zero, 0xF0)                    Field (SATE, DWordAcc, NoLock, Preserve)                    {                                Offset (0x2C),                         SA2C,   32,                                 Offset (0x43),                         SA43,   8,                                 Offset (0xD3),                         SAD3,   8                    }                    Method (_INI, 0, NotSerialized)                    {                    }                    Method (ESAT, 0, NotSerialized)                    {                        Notify (P0P6, Zero)                        And (SAD3, 0x7F, SAD3)                        Or (SA43, 0x40, SA43)                        Store (0x13481043, SA2C)                        And (SA43, 0xBF, SA43)                    }                    Method (ESID, 0, NotSerialized)                    {                        Return (SA2C)                    }                }            }............................    Scope (_GPE)    {        Method (_L01, 0, NotSerialized)        {            \_SB.PCI0.P0P6.JMCC ()            If (LNotEqual (\_SB.PCI0.P0P6.EATA.ESID (), 0x13481043))            {                \_SB.PCI0.P0P6.EATA.ESAT ()            }            If (LNot (And (FDRT, 0x00040000)))            {                If (\_SB.PCI0.P0P4.HPCS)                {                    \_SB.PCI0.P0P4.HPHK ()                    Notify (\_SB.PCI0.P0P4, Zero)                }            }        }

Thanks again for your help!

BTW any chance to get those kexts in X86_X64?


I think that those AppleIntelPIIXPATA warnings aren't a problem. In fact "JMicronATA 4 bytes not aligned" is kind of an error. Maybe you should get back to AppleVIAATA.kext (And that would be better for u cause that's the one i'm using ;) ).

Do you meant x86_64? Well, that's the thing i've corrected. I managed to make DMA with 64 bit addresses to avoid kernel panic. I've not moved DMA to make sure 32 bits is enough to address and make DMA. So this is indeed, a kind of 64 bit address driver.

#102
slashack

slashack

    InsanelyMac Geek

  • Members
  • PipPipPipPip
  • 203 posts
  • Gender:Male
  • Location:Buenos Aires, Argentina

So far so good, tried everything to get kp & nothing! I only replaced AppleNForceATA(Debug)
(now i want to make a system with 8gb haha)

You are a HERO

Kalyway 10.5.2
Asus AN8-SLI - AppleAC97Audio
4gb Ram
Samsung 500 gb sata (remove AppleSMBIOS.kext on install because of crash, place in Extension after build)
AMD Athlon™ 64 FX-25 Processor 5700/2.81Ghz
NVIDIA 7600GS 256mb Nvinject 0.2.0 + Geforce.kext


Be careful. DEBUG kext print tons of information i would need in case they give KP. Use normal kext (without DEBUG), they are the same.

#103
laetilodie

laetilodie

    InsanelyMac Protégé

  • Members
  • Pip
  • 27 posts
Am I the only one who still have kernel panic with the AppleNforceATA 64bits ?

With maxmem=2816 and AppleNforceATA 32 bits i have no error with rember and all work very good.
Without maxmem and AppleNforceATA 32 bits i have errors and kernel panic with rember.

Without maxmem and AppleNforceATA 64 bits no error with rember but 2 times per day when i clic on a file i have a kernel panic.

Posted Image

Posted Image

Config :

Msi P6N SLI-FI (Nforce 650i)
Core2duo 4300 @ 3000
4 Go DDR2
Apple USB Ethernet
8800 GT 512
1 IDE HDD ( Vista, XP, Linux )
2 SATA HDD ( Leopard )

Mac OSX 10.5.5

#104
slashack

slashack

    InsanelyMac Geek

  • Members
  • PipPipPipPip
  • 203 posts
  • Gender:Male
  • Location:Buenos Aires, Argentina

Am I the only one who still have kernel panic with the AppleNforceATA 64bits ?

With maxmem=2816 and AppleNforceATA 32 bits i have no error with rember and all work very good.
Without maxmem and AppleNforceATA 32 bits i have errors and kernel panic with rember.

Without maxmem and AppleNforceATA 64 bits no error with rember but 2 times per day when i clic on a file i have a kernel panic.

Posted Image

Posted Image

Config :

Msi P6N SLI-FI (Nforce 650i)
Core2duo 4300 @ 3000
4 Go DDR2
Apple USB Ethernet
8800 GT 512
1 IDE HDD ( Vista, XP, Linux )
2 SATA HDD ( Leopard )

Mac OSX 10.5.5


There's no evidence there you are using AppleNForceATA.kext. Can u attach "ioreg -l > dump.txt" (run that without quoutes in console and attach dump.txt).

#105
stmiller

stmiller

    InsanelyMac Protégé

  • Members
  • Pip
  • 28 posts
I'm still having problems after trying the AppleVIAATA on p1. Anyone have any ideas?

This is what happens: my 300GB IDE drive shows up as 128GB in Disk Utility; two other SATA connected drives do not show up at all in Disk Utility; applications crashing; and I still have kernel panics. :)

System is a shuttle VIA based SK22G2V2 box, 4GB of ram. 10.4.8. I reverted back to the original AppleVIAATA.kext for now and it is OK, but still have the 4GB bug of course.

This is the portion of my ioreg:

+-o CHN1@1  <class AppleVIAATAChannel, registered, matched, activ$
	 | |   |	 | {
	 | |   |	 |   "acpi-path" = "IOACPIPlane:/_SB/PCI0@0/SATA@f0000/CHN1@1"
	 | |   |	 |   "Control Block Address" = 63232
	 | |   |	 |   "Interrupt Vector" = 20
	 | |   |	 |   "Channel Number" = 1
	 | |   |	 |   "acpi-reg" = <00010000>
	 | |   |	 |   "IOInterruptControllers" = ("io-apic-0")
	 | |   |	 |   "IOInterruptSpecifiers" = (<1400000007000000>)
	 | |   |	 |   "Command Block Address" = 63488
	 | |   |	 | }
	 | |   |	 | 
	 | |   |	 +-o AppleVIAATADriver  <class AppleVIAATADriver, registered, ma$
	 | |   |	   | {
	 | |   |	   |   "Power Management protected data" = "{ theNumberOfPowerSt$
	 | |   |	   |   "Drive 0 Ultra DMA Mode" = 6
	 | |   |	   |   "CFBundleIdentifier" = "com.apple.driver.AppleVIAATA"
	 | |   |	   |   "IOClass" = "AppleVIAATADriver"
	 | |   |	   |   "Drive 0 PIO Mode" = 4
	 | |   |	   |   "IOProbeScore" = 0
	 | |   |	   |   "Power Management private data" = "{ this object = 041ace$
	 | |   |	   |   "IOMatchCategory" = "IODefaultMatchCategory"
	 | |   |	   |   "Physical Interconnect" = "SATA"
	 | |   |	   |   "IOProviderClass" = "AppleVIAATAChannel"
	 | |   |	   | }

Complete dump here.

Attached Files

  • Attached File  dump.txt   233.24KB   7 downloads


#106
laetilodie

laetilodie

    InsanelyMac Protégé

  • Members
  • Pip
  • 27 posts

There's no evidence there you are using AppleNForceATA.kext. Can u attach "ioreg -l > dump.txt" (run that without quoutes in console and attach dump.txt).


Here is my Attached File  dump.txt   362.68KB   11 downloads

#107
slashack

slashack

    InsanelyMac Geek

  • Members
  • PipPipPipPip
  • 203 posts
  • Gender:Male
  • Location:Buenos Aires, Argentina

I'm still having problems after trying the AppleVIAATA on p1. Anyone have any ideas?

This is what happens: my 300GB IDE drive shows up as 128GB in Disk Utility; two other SATA connected drives do not show up at all in Disk Utility; applications crashing; and I still have kernel panics. :)

System is a shuttle VIA based SK22G2V2 box, 4GB of ram. 10.4.8. I reverted back to the original AppleVIAATA.kext for now and it is OK, but still have the 4GB bug of course.

This is the portion of my ioreg:

+-o CHN1@1  <class AppleVIAATAChannel, registered, matched, activ$
	 | |   |	 | {
	 | |   |	 |   "acpi-path" = "IOACPIPlane:/_SB/PCI0@0/SATA@f0000/CHN1@1"
	 | |   |	 |   "Control Block Address" = 63232
	 | |   |	 |   "Interrupt Vector" = 20
	 | |   |	 |   "Channel Number" = 1
	 | |   |	 |   "acpi-reg" = <00010000>
	 | |   |	 |   "IOInterruptControllers" = ("io-apic-0")
	 | |   |	 |   "IOInterruptSpecifiers" = (<1400000007000000>)
	 | |   |	 |   "Command Block Address" = 63488
	 | |   |	 | }
	 | |   |	 | 
	 | |   |	 +-o AppleVIAATADriver  <class AppleVIAATADriver, registered, ma$
	 | |   |	   | {
	 | |   |	   |   "Power Management protected data" = "{ theNumberOfPowerSt$
	 | |   |	   |   "Drive 0 Ultra DMA Mode" = 6
	 | |   |	   |   "CFBundleIdentifier" = "com.apple.driver.AppleVIAATA"
	 | |   |	   |   "IOClass" = "AppleVIAATADriver"
	 | |   |	   |   "Drive 0 PIO Mode" = 4
	 | |   |	   |   "IOProbeScore" = 0
	 | |   |	   |   "Power Management private data" = "{ this object = 041ace$
	 | |   |	   |   "IOMatchCategory" = "IODefaultMatchCategory"
	 | |   |	   |   "Physical Interconnect" = "SATA"
	 | |   |	   |   "IOProviderClass" = "AppleVIAATAChannel"
	 | |   |	   | }

Complete dump here.


Is this dump with my modified kext? I'm developing under leopard, the problem might be if tiger doesn't suppor 64 bit addresses. I really don't know wheither tiger is 64 bits compatible. The issue may have something to do with the api i use from the kernel to make 64 bit dma.

Make sure your devid is in AppleVIAATA Info.plist (I removed every devid but mine, and i really don't know why i made that stupid thing)

by the way, i couldn't download your complete dump.

Here is my Attached File dump.txt ( 362.68K ) Number of downloads: 2


Take a look at this:

+-o IDE0@D  <class IOPCIDevice, registered, matched, active, busy 0, $
	| |   | | {
	| |   | |   "IOPCIResourced" = Yes
	| |   | |   "IOName" = "pci10de,265"
	| |   | |   "subsystem-id" = <50730000>
	| |   | |   "IODeviceMemory" = ({"parent"=({"address"=0,"length"=65536}),"o$
	| |   | |   "acpi-reg" = <00680000>
	| |   | |   "class-code" = <8a010100>
	| |   | |   "IOPowerManagement" = {"ChildrenPowerState"=2,"CurrentPowerStat$
	| |   | |   "revision-id" = <a1000000>
	| |   | |   "assigned-addresses" = <2068008100000000a0ff0000000000001000000$
	| |   | |   "built-in" = <00>
	| |   | |   "device-id" = <65020000>
	| |   | |   "vendor-id" = <de100000>
	| |   | |   "acpi-path" = "IOACPIPlane:/_SB/PCI0@0/IDE0@d0000"
	| |   | |   "subsystem-vendor-id" = <62140000>
	| |   | |   "name" = "pci10de,265"
	| |   | |   "reg" = <006800000000000000000000000000000000000020680001000000$
	| |   | |   "compatible" = <"pci1462,7350","pci10de,265","pciclass,01018a">
	| |   | | }
	| |   | | 
	| |   | +-o AppleOnboardPCATARoot  <class AppleOnboardPCATARoot, !registere$
	| |   |   | {
	| |   |   |   "IOProbeScore" = 10000
	| |   |   |   "IOProviderClass" = "IOPCIDevice"
	| |   |   |   "Hardware Vendor" = "NVIDIA"
	| |   |   |   "CFBundleIdentifier" = "com.apple.driver.AppleOnboardPCATA"
	| |   |   |   "IOMatchCategory" = "IODefaultMatchCategory"
	| |   |   |   "IOPCIPrimaryMatch" = "0x005310de 0x00e510de 0x026510de 0x00d$
	| |   |   |   "IOClass" = "AppleOnboardPCATARoot"
	| |   |   | }
	| |   |   |

All that stuff means your IDE0 has "device-id" = <65020000> and "vendor-id" = <de100000>, that means your IDE controller pciid is 10de:0265 -> NVidia something. The below stuff shows what kext you are using: AppleOnboardPCATARoot. Why this kext? Well, mac matches your devices pciids with all kext pciids listed in Info.plist (under Contents inside the .kext folder). AppleOnboardPCATA seems to be a kext that matches your pciid for your IDE controller: "IOPCIPrimaryMatch" = "0x005310de 0x00e510de 0x026510de 0x00d$.

If you have installed AppleNForceATA.kext correctly, then mac is loading another kext for that device. Either remove AppleOnboardPCATA.kext or remove 0x026510de from IOPCIPrimaryMatch section under AppleOnboardPCATA.kext/Contents/Info.plist. The last one is wich I recommend in case this kext is needed for something else. If this goes wrong, just put back this pciid where it was.

#108
laetilodie

laetilodie

    InsanelyMac Protégé

  • Members
  • Pip
  • 27 posts

Take a look at this:

+-o IDE0@D  <class IOPCIDevice, registered, matched, active, busy 0, $
		 | |   | | {
		 | |   | |   "IOPCIResourced" = Yes
		 | |   | |   "IOName" = "pci10de,265"
		 | |   | |   "subsystem-id" = <50730000>
		 | |   | |   "IODeviceMemory" = ({"parent"=({"address"=0,"length"=65536}),"o$
		 | |   | |   "acpi-reg" = <00680000>
		 | |   | |   "class-code" = <8a010100>
		 | |   | |   "IOPowerManagement" = {"ChildrenPowerState"=2,"CurrentPowerStat$
		 | |   | |   "revision-id" = <a1000000>
		 | |   | |   "assigned-addresses" = <2068008100000000a0ff0000000000001000000$
		 | |   | |   "built-in" = <00>
		 | |   | |   "device-id" = <65020000>
		 | |   | |   "vendor-id" = <de100000>
		 | |   | |   "acpi-path" = "IOACPIPlane:/_SB/PCI0@0/IDE0@d0000"
		 | |   | |   "subsystem-vendor-id" = <62140000>
		 | |   | |   "name" = "pci10de,265"
		 | |   | |   "reg" = <006800000000000000000000000000000000000020680001000000$
		 | |   | |   "compatible" = <"pci1462,7350","pci10de,265","pciclass,01018a">
		 | |   | | }
		 | |   | | 
		 | |   | +-o AppleOnboardPCATARoot  <class AppleOnboardPCATARoot, !registere$
		 | |   |   | {
		 | |   |   |   "IOProbeScore" = 10000
		 | |   |   |   "IOProviderClass" = "IOPCIDevice"
		 | |   |   |   "Hardware Vendor" = "NVIDIA"
		 | |   |   |   "CFBundleIdentifier" = "com.apple.driver.AppleOnboardPCATA"
		 | |   |   |   "IOMatchCategory" = "IODefaultMatchCategory"
		 | |   |   |   "IOPCIPrimaryMatch" = "0x005310de 0x00e510de 0x026510de 0x00d$
		 | |   |   |   "IOClass" = "AppleOnboardPCATARoot"
		 | |   |   | }
		 | |   |   |

All that stuff means your IDE0 has "device-id" = <65020000> and "vendor-id" = <de100000>, that means your IDE controller pciid is 10de:0265 -> NVidia something. The below stuff shows what kext you are using: AppleOnboardPCATARoot. Why this kext? Well, mac matches your devices pciids with all kext pciids listed in Info.plist (under Contents inside the .kext folder). AppleOnboardPCATA seems to be a kext that matches your pciid for your IDE controller: "IOPCIPrimaryMatch" = "0x005310de 0x00e510de 0x026510de 0x00d$.

If you have installed AppleNForceATA.kext correctly, then mac is loading another kext for that device. Either remove AppleOnboardPCATA.kext or remove 0x026510de from IOPCIPrimaryMatch section under AppleOnboardPCATA.kext/Contents/Info.plist. The last one is wich I recommend in case this kext is needed for something else. If this goes wrong, just put back this pciid where it was.


Thank you for the very very quick reply. I remove 0x026510de from IOPCIPrimaryMatch section under AppleOnboardPCATA.kext/Contents/Info.plist.
And now my IDE0 use AppleNForceATARoot

| |   +-o IDE0@D  <class IOPCIDevice, registered, matched, active, busy 0, $
	   | |   | | {
	   | |   | |   "IOPCIResourced" = Yes
	   | |   | |   "IOName" = "pci10de,265"
	   | |   | |   "subsystem-id" = <50730000>
	   | |   | |   "IODeviceMemory" = ({"parent"=({"address"=0,"length"=65536}),"o$
	   | |   | |   "acpi-reg" = <00680000>
	   | |   | |   "class-code" = <8a010100>
	   | |   | |   "IOPowerManagement" = {"ChildrenPowerState"=2,"CurrentPowerStat$
	   | |   | |   "revision-id" = <a1000000>
	   | |   | |   "assigned-addresses" = <2068008100000000a0ff0000000000001000000$
	   | |   | |   "built-in" = <00>
	   | |   | |   "device-id" = <65020000>
	   | |   | |   "vendor-id" = <de100000>
	   | |   | |   "acpi-path" = "IOACPIPlane:/_SB/PCI0@0/IDE0@d0000"
	   | |   | |   "subsystem-vendor-id" = <62140000>
	   | |   | |   "name" = "pci10de,265"
	   | |   | |   "reg" = <006800000000000000000000000000000000000020680001000000$
	   | |   | |   "compatible" = <"pci1462,7350","pci10de,265","pciclass,01018a">
	   | |   | | }
	   | |   | | 
	   | |   | +-o AppleNForceATARoot  <class AppleNForceATARoot, !registered, !ma$
	   | |   |   | {
	   | |   |   |   "IOProbeScore" = 1000
	   | |   |   |   "IOProviderClass" = "IOPCIDevice"
	   | |   |   |   "Serial ATA" = No
	   | |   |   |   "CFBundleIdentifier" = "com.nvidia.driver.AppleNForceATA"
	   | |   |   |   "IOMatchCategory" = "IODefaultMatchCategory"
	   | |   |   |   "IOPCIPrimaryMatch" = "0x01bc10de 0x006510de 0x008510de 0x00d$
	   | |   |   |   "Hardware Name" = "nForce MCP 51"
	   | |   |   |   "IOClass" = "AppleNForceATARoot"
	   | |   |   | }
	   | |   |   | 
	   | |   |   +-o CHN0@0  <class AppleNForceATAChannel, registered, matched, ac$
	   | |   |   | | {
	   | |   |   | |   "IOInterruptSpecifiers" = (<0e00000000000000>)
	   | |   |   | |   "IOInterruptControllers" = ("io-apic-0")
	   | |   |   | |   "acpi-path" = "IOACPIPlane:/_SB/PCI0@0/IDE0@d0000/CHN0@0"
	   | |   |   | |   "acpi-reg" = <00000000>
	   | |   |   | |   "Channel Number" = 0

Is this good for you ?

#109
slashack

slashack

    InsanelyMac Geek

  • Members
  • PipPipPipPip
  • 203 posts
  • Gender:Male
  • Location:Buenos Aires, Argentina

Thank you for the very very quick reply. I remove 0x026510de from IOPCIPrimaryMatch section under AppleOnboardPCATA.kext/Contents/Info.plist.
And now my IDE0 use AppleNForceATARoot

Is this good for you ?


Ok,now u are using AppleNForceATA.kext. Are u experiencing kp's? Dose it works? Try now.

#110
laetilodie

laetilodie

    InsanelyMac Protégé

  • Members
  • Pip
  • 27 posts
No KP for the moment i cross ones fingers.

Thank you very much for your speed.

#111
stmiller

stmiller

    InsanelyMac Protégé

  • Members
  • Pip
  • 28 posts

Is this dump with my modified kext? I'm developing under leopard, the problem might be if tiger doesn't suppor 64 bit addresses. I really don't know wheither tiger is 64 bits compatible. The issue may have something to do with the api i use from the kernel to make 64 bit dma.


Ah I think that's it. Is there any way to include 10.4 compatibility when you compile the VIA driver? :/ I could test that for the heck of it.

#112
slashack

slashack

    InsanelyMac Geek

  • Members
  • PipPipPipPip
  • 203 posts
  • Gender:Male
  • Location:Buenos Aires, Argentina

Ah I think that's it. Is there any way to include 10.4 compatibility when you compile the VIA driver? :/ I could test that for the heck of it.


I don't have any 10.4 box. You can install xcode and download the source from svn (it's the same googlecode project where the kexts are hosted). Otherwise, there's nothing i can do (i don't have any more pcs to install tiger on them and do it).

#113
stmiller

stmiller

    InsanelyMac Protégé

  • Members
  • Pip
  • 28 posts
Hi slashack:

I compiled your AppleVIAATA source under 10.4.8 with xcode 2.5. It works GREAT. I loaded up a large Logic session with many gigs of samples, and I had no kernel panics. Thank you so much!

:D :D

#114
slashack

slashack

    InsanelyMac Geek

  • Members
  • PipPipPipPip
  • 203 posts
  • Gender:Male
  • Location:Buenos Aires, Argentina

Hi slashack:

I compiled your AppleVIAATA source under 10.4.8 with xcode 2.5. It works GREAT. I loaded up a large Logic session with many gigs of samples, and I had no kernel panics. Thank you so much!

:thumbsup_anim: :pirate2:


If u have a gmail account, I can register u at darwinata so u can upload that kext, in case there someone out there with the same problem as you. (I believed mine was a special case, i never expected so much people with the same issue)

#115
live.fx

live.fx

    InsanelyMac Protégé

  • Members
  • Pip
  • 43 posts
  • Gender:Male
Hello, where can i get this source? I have same problems, but after 10.5.5 update. This my post. Random kernel panic, when i work with large amount of data.

this is my post:
http://forum.insanel...howtopic=134477

Some good peoples give me a link with modified AppleVIAATA and Jmicron.kext, but my system can not boot with this kexts. I think i need hard mind work, and source code, for getting worked kext`s...

Big thanks for answer..

#116
slashack

slashack

    InsanelyMac Geek

  • Members
  • PipPipPipPip
  • 203 posts
  • Gender:Male
  • Location:Buenos Aires, Argentina

Hello, where can i get this source? I have same problems, but after 10.5.5 update. This my post. Random kernel panic, when i work with large amount of data.

this is my post:
http://forum.insanel...howtopic=134477

Some good peoples give me a link with modified AppleVIAATA and Jmicron.kext, but my system can not boot with this kexts. I think i need hard mind work, and source code, for getting worked kext`s...

Big thanks for answer..


I've read your post, you need to add your devid to AppleVIAATA.kext. That's why u get an "still waiting for root device" Your KP's logs shows that u have the same problem as me. It's because you are using a 32 bit addressing scheme in your IDE controller kext. Just add your devid

#117
live.fx

live.fx

    InsanelyMac Protégé

  • Members
  • Pip
  • 43 posts
  • Gender:Male

I've read your post, you need to add your devid to AppleVIAATA.kext. That's why u get an "still waiting for root device" Your KP's logs shows that u have the same problem as me. It's because you are using a 32 bit addressing scheme in your IDE controller kext. Just add your devid


Great thanks for fast feedback, slashack ! :blink: I wheel try this.. Right now. With this problem, installation of Update 10.5.5 - is impossible for me..

#118
slashack

slashack

    InsanelyMac Geek

  • Members
  • PipPipPipPip
  • 203 posts
  • Gender:Male
  • Location:Buenos Aires, Argentina

Great thanks for fast feedback, slashack ! :) I wheel try this.. Right now. With this problem, installation of Update 10.5.5 - is impossible for me..


Try testing your memory with rember. (all your memory). And while testing, try to open files, create folders, etc in your IDE hdd. I believe this problem happens in every 10.5.X version.

#119
stmiller

stmiller

    InsanelyMac Protégé

  • Members
  • Pip
  • 28 posts

If u have a gmail account, I can register u at darwinata so u can upload that kext, in case there someone out there with the same problem as you. (I believed mine was a special case, i never expected so much people with the same issue)


Hi slashack,

I've attached a .zip of all of the darwin-ata drivers compiled with xcode 2.5 under 10.4.8. I have only tested the AppleVIAATA on my 10.4.8 system. The others all compiled fine, fwiw.

Attached File  darwin_ata_10_4.zip   484.75KB   10 downloads

#120
slashack

slashack

    InsanelyMac Geek

  • Members
  • PipPipPipPip
  • 203 posts
  • Gender:Male
  • Location:Buenos Aires, Argentina

Hi slashack,

I've attached a .zip of all of the darwin-ata drivers compiled with xcode 2.5 under 10.4.8. I have only tested the AppleVIAATA on my 10.4.8 system. The others all compiled fine, fwiw.

Attached File  darwin_ata_10_4.zip   484.75KB   10 downloads


Thanks! I've uploaded those kexts to googlecode svn in case someone needs them.





0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users

© 2014 InsanelyMac  |   News  |   Forum  |   Downloads  |   OSx86 Wiki  |   Mac Netbook  |   PHP hosting by CatN  |   Designed by Ed Gain  |   Logo by irfan  |   Privacy Policy