darkera13 Posted March 4, 2020 Share Posted March 4, 2020 9 hours ago, ghost8282 said: Thank you for your reply. I opened config.plist with textmate and with show invisible characters and it's ok, no "hidden" or extraneous charaxters. AudioOut 1 and VolumeAmplifier 1000 does not help, it still not works Anyway, I'm attaching my config.plist (log level was changed) if it can help (sensitive data redacted) config.plist I have no idea, sorry 1 Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710948 Share on other sites More sharing options...
ghost8282 Posted March 4, 2020 Share Posted March 4, 2020 (edited) On 3/2/2020 at 5:46 PM, ghost8282 said: 02:569 00:009 HdaControllerGetName(): start 02:578 00:008 HdaControllerGetName(): controller is Intel X79/C600 Series HD Audio Controller 02:587 00:009 HdaControllerReset(): start 02:696 00:109 HdaControllerReset(): done 02:706 00:010 HdaControllerInstallProtocols(): start 02:716 00:010 HdaControllerInitCorb(): start 02:726 00:009 HdaControllerSetCorb(): start 02:735 00:008 HDA controller CORB allocated @ 0x7ECC0000 (0x7ECC0000) (256 entries) 02:743 00:008 HdaControllerInitRirb(): start 02:752 00:008 HdaControllerSetRirb(): start 02:761 00:009 HDA controller RIRB allocated @ 0x7ECBF000 (0x7ECBF000) (256 entries) 02:770 00:009 HdaControllerSetCorb(): start 02:779 00:008 HdaControllerSetRirb(): start 02:788 00:009 HdaControllerInitStreams(): start 02:797 00:009 HdaControllerInitStreams(): in offset 0, out offset 4 02:806 00:008 HdaControllerSetStream(0, 0): start 02:815 00:009 HdaControllerSetStream(1, 0): start 02:825 00:009 HdaControllerSetStream(2, 0): start 02:834 00:009 HdaControllerSetStream(3, 0): start 02:843 00:009 HdaControllerSetStream(4, 0): start 02:852 00:009 HdaControllerSetStream(5, 0): start 02:861 00:009 HdaControllerSetStream(6, 0): start 02:870 00:009 HdaControllerSetStream(7, 0): start 02:879 00:009 HdaControllerScanCodecs(): start 02:888 00:008 HdaControllerScanCodecs(): found codec @ 0x0 02:902 00:014 Assigning output stream 0 to codec 02:912 00:009 Assigning input stream 0 to codec 02:922 00:010 HdaControllerDriverBindingStart(): done 02:932 00:009 HdaCodecDriverBindingSupported(): attaching to codec 0x0 02:941 00:009 HdaCodecDriverBindingStart(): start 02:955 00:014 Codec ID: 0x10EC:0x899 02:969 00:014 Codec name: Realtek ALC899 02:983 00:014 Codec contains 1 function groups, start @ 0x1, end @ 0x1 02:998 00:014 Function group @ 0x1 is of type 0x1 03:047 00:049 Function group @ 0x1 contains 37 widgets, start @ 0x2, end @ 0x26 03:062 00:014 HdaCodecProbeFuncGroup(): probing widgets 05:419 02:357 HdaCodecProbeFuncGroup(): probing widget connections 05:429 00:010 Port widget @ 0x11 is an output (pin defaults 0x99430130) 05:439 00:010 Widget @ 0x10 (type 0x0) 05:454 00:014 Port widget @ 0x14 is an output (pin defaults 0x1114010) 05:464 00:010 Widget @ 0xC (type 0x2) 05:475 00:010 Widget @ 0x2 (type 0x0) 05:499 00:024 Port widget @ 0x15 is an output (pin defaults 0x1011020) 05:509 00:009 Widget @ 0xC (type 0x2) 05:519 00:009 Widget @ 0x2 (type 0x0) 05:539 00:019 Port widget @ 0x16 is an output (pin defaults 0x1016030) 05:548 00:009 Widget @ 0xC (type 0x2) 05:559 00:010 Widget @ 0x2 (type 0x0) 05:579 00:019 Port widget @ 0x17 is an output (pin defaults 0x1012040) 05:589 00:010 Widget @ 0xC (type 0x2) 05:599 00:010 Widget @ 0x2 (type 0x0) 05:619 00:020 Port widget @ 0x1B is an output (pin defaults 0x2214080) 05:630 00:010 Widget @ 0xC (type 0x2) 05:641 00:010 Widget @ 0x2 (type 0x0) 05:666 00:025 Port widget @ 0x1E is an output (pin defaults 0x1456090) 05:676 00:009 Widget @ 0x6 (type 0x0) 06:691 01:015 HdaCodecInstallProtocols(): start Hi, not sure if it's relevant but in the log above I can read Codec Realtek ALC899; looking at DPCIManager codec should be Realtek ALC898. However, this should not be an issue since codecId is 0x10EC0899 Edited March 4, 2020 by ghost8282 Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710955 Share on other sites More sharing options...
Guest Posted March 4, 2020 Share Posted March 4, 2020 (edited) 08:799 00:003 OCABC: MMIO devirt start 08:800 00:000 OCABC: MMIO devirt 0xC1600000 (0x81 pages, 0x8000000000000001) skip 1 08:800 00:000 OCABC: MMIO devirt 0xF8E80000 (0x81 pages, 0x8000000000000001) skip 1 08:801 00:000 OCABC: MMIO devirt 0xF9E80000 (0x81 pages, 0x8000000000000001) skip 0 08:801 00:000 OCABC: MMIO devirt 0xFA000000 (0x100 pages, 0x8000000000000001) skip 1 08:802 00:000 OCABC: MMIO devirt 0xFB100000 (0x181 pages, 0x8000000000000001) skip 1 08:802 00:000 OCABC: MMIO devirt 0xFEA00000 (0x100 pages, 0x8000000000000001) skip 1 08:803 00:000 OCABC: MMIO devirt 0xFEC00000 (0x1 pages, 0x8000000000000001) skip 1 08:804 00:000 OCABC: MMIO devirt 0xFEC10000 (0x1 pages, 0x8000000000000001) skip 1 08:804 00:000 OCABC: MMIO devirt 0xFED00000 (0x1 pages, 0x8000000000000001) skip 1 08:805 00:000 OCABC: MMIO devirt 0xFED40000 (0x5 pages, 0x8000000000000001) skip 1 08:805 00:000 OCABC: MMIO devirt 0xFED80000 (0x10 pages, 0x8000000000000001) skip 1 08:806 00:000 OCABC: MMIO devirt 0xFEDC2000 (0xE pages, 0x8000000000000001) skip 1 08:806 00:000 OCABC: MMIO devirt 0xFEDD4000 (0x2 pages, 0x8000000000000001) skip 1 08:807 00:000 OCABC: MMIO devirt 0xFEE00000 (0x100 pages, 0x8000000000000001) skip 1 08:807 00:000 OCABC: MMIO devirt 0xFF000000 (0x1000 pages, 0x8000000000000001) skip 1 08:808 00:000 OCABC: MMIO devirt 0x2040000000 (0x10400 pages, 0x8000000000000001) skip 1 08:809 00:000 OCABC: MMIO devirt 0x2070000000 (0x10400 pages, 0x8000000000000001) skip 1 08:809 00:000 OCABC: MMIO devirt 0x20A0000000 (0x10400 pages, 0x8000000000000001) skip 1 08:810 00:000 OCABC: MMIO devirt 0x20F0000000 (0x10400 pages, 0x8000000000000001) skip 1 May I ask the meaning of skip 1 or skip 0? the differences i mean Thank you Edited March 4, 2020 by Guest Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710959 Share on other sites More sharing options...
vit9696 Posted March 4, 2020 Share Posted March 4, 2020 (edited) Skip in MMIO devirtualisation means exactly what it says. It skips devirtualisation for the particular region found. — If a region is whitelisted, then devirtualisation does not happen, and skip is 1. — Otherwise the region is permitted to be used by the operating system, and skip is 0. If you have suggestions on how to improve the debug message, feel free to let us know. Edited March 4, 2020 by vit9696 Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710960 Share on other sites More sharing options...
Guest Posted March 4, 2020 Share Posted March 4, 2020 sorry vit9696, in this case was an error of mine (bad ex to decimal conversion) No i have no skill to permit to suggest to you how to improve debug message of your bootloader. I was only trying to follow previously advice given by download fritz to debug my cpu problem Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710962 Share on other sites More sharing options...
mhaeuser Posted March 4, 2020 Share Posted March 4, 2020 @fabiosun add all addresses *up to, including* 0xFF000000 to the whitelist. If you run into alloc errors, remove entries from the whitelist starting with the *lowest* address Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710965 Share on other sites More sharing options...
Guest Posted March 4, 2020 Share Posted March 4, 2020 Thank you Download-Fritz I am doing as you said in above message Best result is after end random seed message an hang on halt critical error with no useful data (in my little knowledge) on debug txt file with all whitelisted memallocation error in the same way as DevirtualizeMMIO is disabled Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710967 Share on other sites More sharing options...
Matgen84 Posted March 4, 2020 Share Posted March 4, 2020 Hi All Iv'e got two issue since OC 0.5.6 Release: Runtime alloc error Halting on critical error My only entry is for Windows: enable or disable, same issue. I can't boot into Catalina 10.15.3. Debug log file in attachment. Need help, please opencore-2020-03-03-161445.txt 1 Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710968 Share on other sites More sharing options...
mhaeuser Posted March 4, 2020 Share Posted March 4, 2020 @Matgen84 enable ProvideCustomSlide and make sure you updated FwRuntimeServices - there is no critical error shown in the log 1 Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710970 Share on other sites More sharing options...
vit9696 Posted March 4, 2020 Share Posted March 4, 2020 @fabiosun, please whitelist all addresses but the ones with 0x10400 pages (PCI controller regions). Then try testing with all the combinations of 0x10400 pages regions in whitelist section and provide: - photos of boot failures in verbose mode - debug logs I.e. you have 4 such regions, so you will have 16 combinations total. From all devirtualised to none devirtualised. Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710973 Share on other sites More sharing options...
Guest Posted March 4, 2020 Share Posted March 4, 2020 thank you vit you mean these one? ---MMIO 0000002040000000-00000020503FFFFF 0000000000010400 8000000000000001 ---MMIO 0000002070000000-00000020803FFFFF 0000000000010400 8000000000000001 ---MMIO 00000020A0000000-00000020B03FFFFF 0000000000010400 8000000000000001 ---MMIO 00000020F0000000-00000021003FFFFF 0000000000010400 8000000000000001 Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710974 Share on other sites More sharing options...
Matgen84 Posted March 4, 2020 Share Posted March 4, 2020 46 minutes ago, Download-Fritz said: @Matgen84 enable ProvideCustomSlide and make sure you updated FwRuntimeServices - there is no critical error shown in the log ProvideCustomSlide is enabled, FwRuntimeServices is up to date. Strange. Test on Z390 Aorus Master - 10.15.3 Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710979 Share on other sites More sharing options...
vit9696 Posted March 4, 2020 Share Posted March 4, 2020 Correct, you can also find them in the log: 0x2040000000 (0x10400 pages, 0x8000000000000001) skip 1 08:809 00:000 OCABC: MMIO devirt 0x2070000000 (0x10400 pages, 0x8000000000000001) skip 1 08:809 00:000 OCABC: MMIO devirt 0x20A0000000 (0x10400 pages, 0x8000000000000001) skip 1 08:810 00:000 OCABC: MMIO devirt 0x20F0000000 (0x10400 pages, 0x8000000000000001) skip 1 Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710982 Share on other sites More sharing options...
Guest Posted March 4, 2020 Share Posted March 4, 2020 (edited) ok 09:480 00:000 OCABC: MMIO devirt 0x2040000000 (0x10400 pages, 0x8000000000000001) skip 0 09:480 00:000 OCABC: MMIO devirt 0x2070000000 (0x10400 pages, 0x8000000000000001) skip 1 09:481 00:000 OCABC: MMIO devirt 0x20A0000000 (0x10400 pages, 0x8000000000000001) skip 1 09:481 00:000 OCABC: MMIO devirt 0x20F0000000 (0x10400 pages, 0x8000000000000001) skip 1 attached first debug and verbose grab (after End RandomSeed system reboots) This also for first for combinations tested: 0111 0011 0001 0000 and also: 1011 1001 produces an instant reboot on IMG_0370 and on opencore-2020-03-04-104745.txt you can see what happens with: 1111 condition i am continuing with 4! combinations thank you again for your time s opencore-2020-03-04-104745.txt Edited March 4, 2020 by Guest Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710987 Share on other sites More sharing options...
mhaeuser Posted March 4, 2020 Share Posted March 4, 2020 @fabiosun you did not whitelist all other addresses as we both said... Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710988 Share on other sites More sharing options...
Cloverkit Posted March 4, 2020 Share Posted March 4, 2020 OpenCore 0.5.6 cannot boot Arch Linux (Grub2) OCB: LoadImage failed -Not Found Halting on critical error 1 Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710989 Share on other sites More sharing options...
Guest Posted March 4, 2020 Share Posted March 4, 2020 sorry.. you mean this? 09:471 00:000 OCABC: MMIO devirt 0xC1600000 (0x81 pages, 0x8000000000000001) skip 0 09:472 00:000 OCABC: MMIO devirt 0xF8E80000 (0x81 pages, 0x8000000000000001) skip 0 09:472 00:000 OCABC: MMIO devirt 0xF9E80000 (0x81 pages, 0x8000000000000001) skip 0 09:473 00:000 OCABC: MMIO devirt 0xFA000000 (0x100 pages, 0x8000000000000001) skip 0 09:473 00:000 OCABC: MMIO devirt 0xFB100000 (0x181 pages, 0x8000000000000001) skip 0 09:474 00:000 OCABC: MMIO devirt 0xFEA00000 (0x100 pages, 0x8000000000000001) skip 0 09:474 00:000 OCABC: MMIO devirt 0xFEC00000 (0x1 pages, 0x8000000000000001) skip 0 09:475 00:000 OCABC: MMIO devirt 0xFEC10000 (0x1 pages, 0x8000000000000001) skip 0 09:475 00:000 OCABC: MMIO devirt 0xFED00000 (0x1 pages, 0x8000000000000001) skip 0 09:477 00:001 OCABC: MMIO devirt 0xFED40000 (0x5 pages, 0x8000000000000001) skip 0 09:477 00:000 OCABC: MMIO devirt 0xFED80000 (0x10 pages, 0x8000000000000001) skip 0 09:478 00:000 OCABC: MMIO devirt 0xFEDC2000 (0xE pages, 0x8000000000000001) skip 0 09:478 00:000 OCABC: MMIO devirt 0xFEDD4000 (0x2 pages, 0x8000000000000001) skip 0 09:479 00:000 OCABC: MMIO devirt 0xFEE00000 (0x100 pages, 0x8000000000000001) skip 0 09:479 00:000 OCABC: MMIO devirt 0xFF000000 (0x1000 pages, 0x8000000000000001) skip 0 Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710990 Share on other sites More sharing options...
mhaeuser Posted March 4, 2020 Share Posted March 4, 2020 yes Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710991 Share on other sites More sharing options...
Guest Posted March 4, 2020 Share Posted March 4, 2020 thank you Download-Fritz and vit9696 and sorry for delay to execute your advice: attached all debug for 16 combinations and only 2 verbose pictures 1 is related to opencore-2020-03-04-125212.txt (mem allocation error) the Others is verbose for all Others combinations (End RandomSeed and then instant reboot) Thank you for your time again opencore-2020-03-04-122712.txt opencore-2020-03-04-123212.txt opencore-2020-03-04-123459.txt opencore-2020-03-04-123742.txt opencore-2020-03-04-124137.txt opencore-2020-03-04-124457.txt opencore-2020-03-04-124936.txt opencore-2020-03-04-125212.txt opencore-2020-03-04-130237.txt opencore-2020-03-04-130601.txt opencore-2020-03-04-130858.txt opencore-2020-03-04-131203.txt opencore-2020-03-04-131852.txt opencore-2020-03-04-132207.txt opencore-2020-03-04-132522.txt opencore-2020-03-04-132944.txt Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2710998 Share on other sites More sharing options...
mhaeuser Posted March 4, 2020 Share Posted March 4, 2020 @fabiosun ok, this was correct. Well, AMD kernel patches are borked then. 1 Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2711000 Share on other sites More sharing options...
ghost8282 Posted March 4, 2020 Share Posted March 4, 2020 Can I be of any help by providing additional information/files/etc. regarding this? Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2711002 Share on other sites More sharing options...
insanefrancis Posted March 4, 2020 Share Posted March 4, 2020 Hi, What does alcid= <layout> exactly do? My audio is already working properly and I don't have this on my boot-args. I've just read some post recommending to put it if using AppleALC.kext. Also, is it safe to remove nvda_drv from my config.plist if I'm not using NVidia card? Just my OCD ☺️. Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2711017 Share on other sites More sharing options...
Andrey1970 Posted March 4, 2020 Share Posted March 4, 2020 28 minutes ago, insanefrancis said: What does alcid= <layout> Option for layout, it is convenient for beginners. 35 minutes ago, insanefrancis said: Also, is it safe to remove nvda_drv from my config.plist if I'm not using NVidia card? Yes. 1 Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2711024 Share on other sites More sharing options...
Orion's Sword Posted March 4, 2020 Share Posted March 4, 2020 I'm getting a KP on 0.5.6. Probably because I've messed something up. config_0.5.5.plist config_0.5.6.plist Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2711049 Share on other sites More sharing options...
xh116 Posted March 4, 2020 Share Posted March 4, 2020 (edited) I picked several useful message... (for someone to search the same problem by keywords) "can't perform kext scan : no kext summary system uptime in nanoseconds :735279778 In memory panic stackshot succeeded " anybody news what problem is? and what should I do... EFI.zip Edited March 4, 2020 by xh116 Link to comment https://www.insanelymac.com/forum/topic/350754-opencore-general-discussion/page/134/#findComment-2711066 Share on other sites More sharing options...
Recommended Posts