Jump to content

HELP TOPIC - [RYZEN] macOS 10.12.x (Sierra)

spakk

By spakk,
in macOS 10.12 (Sierra)

 Share
410 posts in this topic

Recommended Posts

Shaneee
Shaneee
Posted
Posted

I just tried it with -v

 

here the preboot log

 

Edit: I just deactivated FixUSB in Clover Configurator.

Error message on attached screenshot

 

Are you using the RTC Patch in Clover?

Link to comment
Share on other sites
gills83
gills83
Posted
Posted

I just tried it with -v

 

here the preboot log

 

Edit: I just deactivated FixUSB in Clover Configurator.

Error message on attached screenshot

 

Edit2: npci=0x3000 busratio=32 -v and selecting InjectEDID and InjectATI (Futomaki) lets me boot into Sierra but I can see the Sierra Wallpaper for only a second, then my display turns into standby mode and after about a minute my pc goes into standby. Any ideas?

yeah !!  :)

 

we are going forward

0:100  0:100  MemLog inited, TSC freq: 3194492160
0:100  0:000  CPU was calibrated without ACPI PM Timer: Intel ICH device was not found., use RTC
0:100  0:000  
0:100  0:000  Now is 7.6.2017,  19:19:12 (GMT)
0:100  0:000  Starting Clover revision: 4078 on American Megatrends EFI
0:100  0:000  Build with: [Args: cleanlib | -D USE_LOW_EBDA -a X64 -b RELEASE -t XCODE5 -n 3 cleanlib | OS: 10.9.5 | XCODE: 6.2]
0:100  0:000  SelfDevicePath=PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x1)\Sata(0x5,0xFFFF,0x0)\HD(1,GPT,DFC9111F-94A3-4EF1-BB8A-A114C25F903B,0x28,0x64000) @D87AD218
0:100  0:000  SelfDirPath = \EFI\BOOT
0:102  0:002  === [ Get Smbios ] ========================================
0:102  0:000  Type 16 Index = 0
0:102  0:000  Total Memory Slots Count = 4
0:102  0:000  Type 17 Index = 0
0:102  0:000  Table has error information, checking
0:102  0:000  Found memory information in table 18/1, type=0x3, operation=0x2 syndrome=0x0
0:102  0:000  ...memory OK
0:102  0:000  SmbiosTable.Type17->Speed = 2133MHz
0:102  0:000  SmbiosTable.Type17->Size = 16384MB
0:102  0:000  SmbiosTable.Type17->Bank/Device = CHANNEL A DIMM 0
0:102  0:000  SmbiosTable.Type17->Vendor = Unknown
0:102  0:000  SmbiosTable.Type17->SerialNumber = A7105D96
0:102  0:000  SmbiosTable.Type17->PartNumber = CT16G4DFD8213.C16FAD
0:102  0:000  Type 17 Index = 1
0:102  0:000  Table has error information, checking
0:102  0:000  Found memory information in table 18/2, type=0x3, operation=0x2 syndrome=0x0
0:102  0:000  ...memory OK
0:102  0:000  SmbiosTable.Type17->Speed = 2133MHz
0:102  0:000  SmbiosTable.Type17->Size = 16384MB
0:102  0:000  SmbiosTable.Type17->Bank/Device = CHANNEL A DIMM 1
0:102  0:000  SmbiosTable.Type17->Vendor = Unknown
0:102  0:000  SmbiosTable.Type17->SerialNumber = E0139282
0:102  0:000  SmbiosTable.Type17->PartNumber = CT16G4DFD8213.C16FAD
0:102  0:000  Type 17 Index = 2
0:102  0:000  Table has error information, checking
0:102  0:000  Found memory information in table 18/3, type=0x3, operation=0x2 syndrome=0x0
0:102  0:000  ...memory OK
0:102  0:000  SmbiosTable.Type17->Speed = 2133MHz
0:102  0:000  SmbiosTable.Type17->Size = 16384MB
0:102  0:000  SmbiosTable.Type17->Bank/Device = CHANNEL B DIMM 0
0:102  0:000  SmbiosTable.Type17->Vendor = Unknown
0:102  0:000  SmbiosTable.Type17->SerialNumber = E02B5AD5
0:102  0:000  SmbiosTable.Type17->PartNumber = CT16G4DFD8213.M16FB
0:102  0:000  Type 17 Index = 3
0:102  0:000  Table has error information, checking
0:102  0:000  Found memory information in table 18/4, type=0x3, operation=0x2 syndrome=0x0
0:102  0:000  ...memory OK
0:102  0:000  SmbiosTable.Type17->Speed = 2133MHz
0:102  0:000  SmbiosTable.Type17->Size = 16384MB
0:102  0:000  SmbiosTable.Type17->Bank/Device = CHANNEL B DIMM 1
0:102  0:000  SmbiosTable.Type17->Vendor = Unknown
0:102  0:000  SmbiosTable.Type17->SerialNumber = E0139265
0:102  0:000  SmbiosTable.Type17->PartNumber = CT16G4DFD8213.C16FAD
0:102  0:000  Boot status=0
0:102  0:000  Running on: 'AB350-Gaming 3' with board 'AB350-Gaming 3-CF'
0:102  0:000  === [ GetCPUProperties ] ==================================
0:102  0:000  CPU Vendor = 68747541 Model=800F11
0:102  0:000   The CPU supported SSE4.1
0:102  0:000  	Looking to disable C1E if is already enabled by the BIOS:
0:102  0:000  BrandString = AMD Ryzen 5 1600 Six-Core Processor            
0:102  0:000  gCPUStructure.TSCFrequency: 3200
0:102  0:000  MaxRatio: f 
0:102  0:000  busFrequency: 0 MHz 
, cpuMult: 64 
, cpuFrequency: 3200 
0:102  0:000  MaxDiv/MinDiv: 32.0/8
0:102  0:000  Turbo: 0/0/0/0
0:102  0:000  Features: 0x178BFBFF
0:102  0:000  Threads: 12
0:102  0:000  Cores: 12
0:102  0:000  FSB: 25 MHz
0:102  0:000  CPU: 0 MHz
0:102  0:000  TSC: 3200 MHz
0:102  0:000  PIS: 100 MHz
0:102  0:000  === [ GetDevices ] ========================================
0:102  0:000  PCI (00|00:00.00) : 1022 1450 class=060000
0:102  0:000  PCI (00|00:00.02) : 1022 1451 class=080600
0:102  0:000  PCI (00|00:01.00) : 1022 1452 class=060000
0:102  0:000  PCI (00|00:01.03) : 1022 1453 class=060400
0:102  0:000  PCI (00|03:00.00) : 1022 43BB class=0C0330
0:102  0:000  PCI (00|03:00.01) : 1022 43B7 class=010601
0:102  0:000  PCI (00|03:00.02) : 1022 43B2 class=060400
0:102  0:000  PCI (00|04:00.00) : 1022 43B4 class=060400
0:102  0:000  PCI (00|05:00.00) : 10EC 8168 class=020000
0:102  0:000   - LAN: 0 Vendor=Realtek
0:102  0:000  PCI (00|04:01.00) : 1022 43B4 class=060400
0:102  0:000  PCI (00|04:04.00) : 1022 43B4 class=060400
0:102  0:000  PCI (00|00:02.00) : 1022 1452 class=060000
0:102  0:000  PCI (00|00:03.00) : 1022 1452 class=060000
0:102  0:000  PCI (00|00:03.01) : 1022 1453 class=060400
0:102  0:000  PCI (00|09:00.00) : 1002 6798 class=030000
0:102  0:000   - GFX: Model=AMD Radeon HD 7970X/8970/R9 280X (ATI/AMD)
0:102  0:000   - RADEON_BIOS_0_SCRATCH = 0x00000050
0:102  0:000  PCI (00|09:00.01) : 1002 AAA0 class=040300
0:102  0:000   - HDMI Audio: 
0:102  0:000  PCI (00|00:04.00) : 1022 1452 class=060000
0:102  0:000  PCI (00|00:07.00) : 1022 1452 class=060000
0:102  0:000  PCI (00|00:07.01) : 1022 1454 class=060400
0:103  0:000  PCI (00|11:00.00) : 1022 145A class=130000
0:103  0:000  PCI (00|11:00.02) : 1022 1456 class=108000
0:103  0:000  PCI (00|11:00.03) : 1022 145C class=0C0330
0:103  0:000  PCI (00|00:08.00) : 1022 1452 class=060000
0:103  0:000  PCI (00|00:08.01) : 1022 1454 class=060400
0:103  0:000  PCI (00|12:00.00) : 1022 1455 class=130000
0:103  0:000  PCI (00|12:00.02) : 1022 7901 class=010601
0:103  0:000  PCI (00|12:00.03) : 1022 1457 class=040300
0:103  0:000  PCI (00|00:14.00) : 1022 790B class=0C0500
0:103  0:000  PCI (00|00:14.03) : 1022 790E class=060100
0:103  0:000  PCI (00|00:18.00) : 1022 1460 class=060000
0:103  0:000  PCI (00|00:18.01) : 1022 1461 class=060000
0:103  0:000  PCI (00|00:18.02) : 1022 1462 class=060000
0:103  0:000  PCI (00|00:18.03) : 1022 1463 class=060000
0:103  0:000  PCI (00|00:18.04) : 1022 1464 class=060000
0:103  0:000  PCI (00|00:18.05) : 1022 1465 class=060000
0:103  0:000  PCI (00|00:18.06) : 1022 1466 class=060000
0:103  0:000  PCI (00|00:18.07) : 1022 1467 class=060000
0:103  0:000  === [ GetDefaultSettings ] ================================
0:103  0:000  Clover load options size = 0 bytes
0:115  0:012  EFI\CLOVER\config.plist loaded: Success
0:115  0:000  === [ GetListOfThemes ] ===================================
0:116  0:000  - [00]: BGM
0:121  0:005  - [01]: embedded
0:125  0:003  - [01]: random
0:128  0:003  - [01]: metal
0:134  0:005  === [ Found config plists ] ===============================
0:135  0:001  - config.plist
0:136  0:001  === [ GetEarlyUserSettings ] ==============================
0:136  0:000  timeout set to 5
0:136  0:000  Custom boot CUSTOM_BOOT_DISABLED (0x0)
0:136  0:000  Default theme: BGM
0:136  0:000  === [ LoadDrivers ] =======================================
0:137  0:001  Loading AppleImageCodec-64.efi  status=Success
0:144  0:006  Loading AppleKeyAggregator-64.efi  status=Success
0:148  0:004  Loading AppleUITheme-64.efi  status=Success
0:153  0:005  Loading DataHubDxe-64.efi  status=Success
0:159  0:005  Loading FirmwareVolume-64.efi  status=Success
0:163  0:004  Loading FSInject-64.efi  status=Success
0:168  0:005  Loading OsxAptioFixDrv-64.efi  status=Success
0:173  0:004  Loading OsxFatBinaryDrv-64.efi  status=Success
0:178  0:005  Loading PartitionDxe-64.efi  status=Success
0:183  0:005   - driver needs connecting
0:183  0:000  Loading SMCHelper-64.efi  status=Success
0:188  0:005  Loading VBoxHfs-64.efi  status=Success
0:194  0:005   - driver needs connecting
0:194  0:000  2 drivers needs connecting ...
0:194  0:000  PlatformDriverOverrideProtocol->GetDriver overriden
0:194  0:000  Partition driver loaded: 
0:194  0:000  Searching for invalid DiskIo BY_DRIVER connects: not found, all ok
0:484  0:289  === [ InitScreen ] ========================================
0:484  0:000  SetScreenResolution: 1280x1024 - setting Mode 4
0:552  0:068  Video mode change to mode #4: Success
0:552  0:000  Console modes reported: 4, available modes:
0:552  0:000   - [01]: 80x25
0:552  0:000   - [02]: 80x50
0:552  0:000   - [03]: 100x31
0:552  0:000   - [04]: 127x33 (current mode)
0:552  0:000  SetScreenResolution: 1280x1024 - already set
0:552  0:000  reinit: self device path=PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x1)\Sata(0x5,0xFFFF,0x0)\HD(1,GPT,DFC9111F-94A3-4EF1-BB8A-A114C25F903B,0x28,0x64000)
0:555  0:003  Using embedded font: Success
0:957  0:401  === [ GetMacAddress ] =====================================
0:957  0:000   get legacy LAN MAC, 1 card found
0:957  0:000  Legacy MAC address of LAN #0= 1C:1B:0D:E1:F1:A1:
0:957  0:000  === [ ScanSPD ] ===========================================
0:957  0:000  === [ GetAcpiTablesList ] =================================
0:957  0:000  Get Acpi Tables List from RSDT:
0:957  0:000   - [00]: FACP  A M I len=132
0:957  0:000   - [01]: APIC  A M I len=222
0:957  0:000   - [02]: FPDT  A M I len=68
0:957  0:000   - [03]: SSDT   len=35916
0:957  0:000   - [04]: FIDT  A M I len=156
0:957  0:000   - [05]: SSDT  AmdTable len=6324
0:957  0:000   - [06]: SRAT  AmdTable len=240
0:957  0:000   - [07]: CRAT  AmdTable len=3024
0:957  0:000   - [08]: CDIT  AmdTable len=41
0:957  0:000   - [09]: SSDT  AOD len=6113
0:957  0:000   - [10]: MCFG  A M I len=60
0:957  0:000   - [11]: HPET  A M I len=56
0:957  0:000   - [12]: SSDT  FCHZP len=36
0:957  0:000   - [13]: UEFI   len=66
0:957  0:000   - [14]: IVRS   len=208
0:957  0:000   - [15]: BGRT  ALASKAA  len=56
0:957  0:000   - [16]: SSDT   len=248
0:957  0:000   - [17]: SSDT  CPMCMN len=5732
0:957  0:000  Calibrated TSC frequency =3194492160 =3194MHz
0:957  0:000  === [ GetUserSettings ] ===================================
0:957  0:000  USB FixOwnership: yes
0:957  0:000  Dropping 3 tables:
0:957  0:000   - [00]: Drop table  signature="DMAR" (52414D44)
0:957  0:000           - set table: 52414D44,                0 to drop: no
0:957  0:000   - [01]: Drop table  signature="SSDT" (54445353) table-id="CpuPm" (0000006D50757043)
0:957  0:000           - set table: 54445353,       6D50757043 to drop: no
0:957  0:000   - [02]: Drop table  signature="SSDT" (54445353) table-id="Cpu0Ist" (0074734930757043)
0:957  0:000           - set table: 54445353,   74734930757043 to drop: no
0:957  0:000   - final DSDT Fix mask=1FE6F9D7
0:961  0:003  === [ ScanVolumes ] =======================================
0:961  0:000  Found 6 volumes with blockIO
0:961  0:000  - [00]: Volume: PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x0)\USB(0xC,0x0)
0:963  0:001          USB volume
0:963  0:000  - [01]: Volume: PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x0)\USB(0xC,0x0)\HD(1,MBR,0x00000000,0x2,0x3C3FFE)
0:964  0:001          Result of bootcode detection: bootable unknown (legacy)
0:964  0:000          USB volume
0:970  0:005  - [02]: Volume: PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x1)\Sata(0x5,0xFFFF,0x0)
0:971  0:000  - [03]: Volume: PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x1)\Sata(0x5,0xFFFF,0x0)\HD(1,GPT,DFC9111F-94A3-4EF1-BB8A-A114C25F903B,0x28,0x64000)
0:971  0:000          Result of bootcode detection: bootable unknown (legacy)
0:973  0:001          This is SelfVolume !!
0:973  0:000  - [04]: Volume: PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x1)\Sata(0x5,0xFFFF,0x0)\HD(2,GPT,7ECA1F23-3573-4172-8FA6-47AF12C65177,0x64028,0x3A1EC0C0)
0:973  0:000  - [05]: Volume: PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x1)\Sata(0x5,0xFFFF,0x0)\HD(3,GPT,6A00922A-4470-4110-A19B-544C0149B08C,0x3A2500E8,0x135F20)
0:974  0:000  === [ InitTheme ] =========================================
0:980  0:006  Using theme 'BGM' (EFI\CLOVER\themes\BGM)
0:980  0:000  OS main and drive as badge
0:984  0:004  Loading font from ThemeDir: Success
0:985  0:000  Choosing theme BGM
0:986  0:001  after NVRAM boot-args=
0:986  0:000  === [ Dump SMC keys from NVRAM ] ==========================
0:986  0:000  found AppleSMC protocol
1:057  0:070  === [ ScanLoader ] ========================================
1:057  0:000  - [01]: 'O T'
1:102  0:045  - [03]: 'EFI'
1:157  0:054  - [04]: 'macOS'
1:162  0:004          AddLoaderEntry for Volume Name=macOS
1:164  0:001      Check if volume Is Hibernated:
1:164  0:000      Check sleep image 'by signature':
1:177  0:013      read prefs \Library\Preferences\com.apple.PowerManagement.plist status=Success
1:177  0:000      using default sleep image name = \private\var\vm\sleepimage
1:182  0:005      no valid sleep image offset was found
1:182  0:000       sleepimage offset could not be acquired
1:182  0:000      hibernated: no - sign
1:185  0:003          [!] Icon 17 (icons\vol_internal_hfs.icns) not found (path: EFI\CLOVER\themes\BGM)
1:227  0:041  - [05]: 'Recovery HD'
1:228  0:001          AddLoaderEntry for Volume Name=Recovery HD
1:272  0:044  Scanning legacy ...
1:272  0:000  === [ AddCustomTool ] =====================================
1:276  0:003  found tool \EFI\CLOVER\tools\Shell64U.efi
1:276  0:000  Checking EFI partition Volume 3 for Clover
1:279  0:003   Found Clover
1:291  0:011  === [ GetEfiBootDeviceFromNvram ] =========================
1:293  0:002   - efi-boot-device-data: PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x1)\Sata(0x5,0xFFFF,0x0)\HD(2,GPT,7ECA1F23-3573-4172-8FA6-47AF12C65177,0x64028,0x3A1EC0C0)
1:293  0:000    - Volume: 'PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x1)\Sata(0x5,0xFFFF,0x0)\HD(2,GPT,7ECA1F23-3573-4172-8FA6-47AF12C65177,0x64028,0x3A1EC0C0)'
1:293  0:000    - LoaderPath: '<null string>'
1:293  0:000    - Guid = 7ECA1F23-3573-4172-8FA6-47AF12C65177
1:293  0:000  === [ FindStartupDiskVolume ] =============================
1:293  0:000    - Volume: partition = PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x1)\Sata(0x5,0xFFFF,0x0)\HD(2,GPT,7ECA1F23-3573-4172-8FA6-47AF12C65177,0x64028,0x3A1EC0C0)
1:293  0:000     - searching for that partition
1:293  0:000      - found entry 0. 'Boot macOS from macOS', Volume 'macOS'
1:293  0:000  Boot redirected to Entry 0. 'Boot macOS from macOS'
1:293  0:000  DefaultIndex=0 and MainMenu.EntryCount=8
1:615  0:322  GUI ready
22:996  21:380  ReinitSelfLib after theme change
22:996  0:000  reinit: self device path=PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x1)\Sata(0x5,0xFFFF,0x0)\HD(1,GPT,DFC9111F-94A3-4EF1-BB8A-A114C25F903B,0x28,0x64000)
22:998  0:002  === [ ScanVolumes ] =======================================
22:998  0:000  Found 6 volumes with blockIO
22:998  0:000  - [00]: Volume: PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x0)\USB(0xC,0x0)
22:999  0:001          USB volume
22:999  0:000  - [01]: Volume: PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x0)\USB(0xC,0x0)\HD(1,MBR,0x00000000,0x2,0x3C3FFE)
23:001  0:001          Result of bootcode detection: bootable unknown (legacy)
23:001  0:000          USB volume
23:001  0:000  - [02]: Volume: PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x1)\Sata(0x5,0xFFFF,0x0)
23:001  0:000  - [03]: Volume: PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x1)\Sata(0x5,0xFFFF,0x0)\HD(1,GPT,DFC9111F-94A3-4EF1-BB8A-A114C25F903B,0x28,0x64000)
23:002  0:000          Result of bootcode detection: bootable unknown (legacy)
23:003  0:001          This is SelfVolume !!
23:003  0:000  - [04]: Volume: PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x1)\Sata(0x5,0xFFFF,0x0)\HD(2,GPT,7ECA1F23-3573-4172-8FA6-47AF12C65177,0x64028,0x3A1EC0C0)
23:004  0:000  - [05]: Volume: PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x1)\Sata(0x5,0xFFFF,0x0)\HD(3,GPT,6A00922A-4470-4110-A19B-544C0149B08C,0x3A2500E8,0x135F20)
23:004  0:000  Choosing theme BGM
23:006  0:001  after NVRAM boot-args=
23:006  0:000  === [ ScanLoader ] ========================================
23:006  0:000  - [01]: 'O T'
23:044  0:037  - [03]: 'EFI'
23:098  0:053  - [04]: 'macOS'
23:098  0:000          AddLoaderEntry for Volume Name=macOS
23:099  0:000      Check if volume Is Hibernated:
23:099  0:000      Check sleep image 'by signature':
23:111  0:012      read prefs \Library\Preferences\com.apple.PowerManagement.plist status=Success
23:111  0:000      using default sleep image name = \private\var\vm\sleepimage
23:116  0:004      no valid sleep image offset was found
23:116  0:000       sleepimage offset could not be acquired
23:116  0:000      hibernated: no - sign
23:156  0:040  - [05]: 'Recovery HD'
23:156  0:000          AddLoaderEntry for Volume Name=Recovery HD
23:197  0:040  Scanning legacy ...
23:197  0:000  === [ AddCustomTool ] =====================================
23:198  0:001  found tool \EFI\CLOVER\tools\Shell64U.efi
23:198  0:000  Checking EFI partition Volume 3 for Clover
23:201  0:003   Found Clover
23:201  0:000  === [ GetEfiBootDeviceFromNvram ] =========================
23:201  0:000  === [ FindStartupDiskVolume ] =============================
23:201  0:000    - Volume: partition = PciRoot(0x0)\Pci(0x1,0x3)\Pci(0x0,0x1)\Sata(0x5,0xFFFF,0x0)\HD(2,GPT,7ECA1F23-3573-4172-8FA6-47AF12C65177,0x64028,0x3A1EC0C0)
23:201  0:000     - searching for that partition
23:201  0:000      - found entry 0. 'Boot macOS from macOS', Volume 'macOS'
23:201  0:000  Boot redirected to Entry 0. 'Boot macOS from macOS'
23:201  0:000  DefaultIndex=0 and MainMenu.EntryCount=8
48:332  25:131   enter menu with LoadOptions: <null string>
48:332  0:000   and with FlagsBits = 0x7
64:074  15:741   exit menu with LoadOptions: -v 
64:074  0:000   boot with args: -v 
64:075  0:000  ParseBootOption: invalid boot variable
64:075  0:000  BootVariable of the entry is empty
64:075  0:000  === [ StartLoader ] =======================================
64:075  0:000  Finally: Bus=99827kHz CPU=3194MHz
64:075  0:000  Loading boot.efi  status=Success
64:161  0:086  GetOSVersion: 10.12.5 (16F73)
64:162  0:000  CSR_CFG: CSR_ALLOW_UNTRUSTED_KEXTS | CSR_ALLOW_UNRESTRICTED_FS | CSR_ALLOW_TASK_FOR_PID | CSR_ALLOW_UNRESTRICTED_DTRACE | CSR_ALLOW_UNRESTRICTED_NVRAM
64:162  0:000  === [ PatchSmbios ] =======================================
64:162  0:000  insert table 9 for dev 0:0
64:162  0:000  insert table 9 for dev 0:1
64:162  0:000  insert table 9 for dev 0:0
64:162  0:000  Trusting SMBIOS...
64:162  0:000  Detected alternating SMBIOS channel banks
64:162  0:000  Channels: 4
64:162  0:000  Interleave: 0 2 4 6 1 3 5 7 8 10 12 14 9 11 13 15 16 18 20 22 17 19 21 23
64:162  0:000   partNum=CT16G4DFD8213.C16FAD
64:162  0:000  SMBIOS Type 17 Index = 0 => 0 0:
64:162  0:000  BANK 0 DIMM0 2133MHz 16384MB
64:162  0:000   partNum=CT16G4DFD8213.C16FAD
64:162  0:000  SMBIOS Type 17 Index = 1 => 1 2:
64:162  0:000  BANK 1 DIMM0 2133MHz 16384MB
64:162  0:000   partNum=CT16G4DFD8213.M16FB
64:162  0:000  SMBIOS Type 17 Index = 2 => 2 4:
64:162  0:000  BANK 2 DIMM0 2133MHz 16384MB
64:162  0:000   partNum=CT16G4DFD8213.C16FAD
64:162  0:000  SMBIOS Type 17 Index = 3 => 3 6:
64:162  0:000  BANK 3 DIMM0 2133MHz 16384MB
64:162  0:000  mTotalSystemMemory = 65536
64:162  0:000  NumberOfMemoryDevices = 4
64:162  0:000  === [ PatchACPI ] =========================================
64:162  0:000  RSDT 0xDC096028
64:162  0:000  FADT from RSDT: 0xDC096160
64:162  0:000  XSDT 0xDC096098
64:162  0:000  FADT from XSDT: 0xDC09BAD8
64:162  0:000  Xsdt reallocation done
64:162  0:000  old FADT length=114
64:162  0:000  Found OperationRegion(GSMM, SystemMemory, FED80000, ...)
64:162  0:000  Found OperationRegion(SSDT, SystemMemory, FFFF0000, ...)
64:162  0:000  Found OperationRegion(LUIE, SystemMemory, FEDC0020, ...)
64:162  0:000  Found OperationRegion(TMMB, SystemMemory, FED40000, ...)
64:162  0:000  Found OperationRegion(CRBD, SystemMemory, FED40000, ...)
64:162  0:000  Found OperationRegion(TPMR, SystemMemory, FFFFFFFF, ...)
64:162  0:000  Found OperationRegion(ATNV, SystemMemory, FFFF0000, ...)
64:163  0:001  Apply DsdtFixMask=0x1FE6F9D7
64:163  0:000     drop _DSM mask=0xFFFF
64:163  0:000  === [ FixBiosDsdt ] =======================================
64:163  0:000  USBADR[0] = 0x10003 and PCIe = 0x0
64:164  0:000  VideoCard devID=0x67981002
64:164  0:000  DisplayADR1[0] = 0x30001, DisplayADR2[0] = 0x0
64:164  0:000  USBADR[1] = 0x70001 and PCIe = 0x3
64:188  0:024  first CPU found at 3AAC offset 3AB0
64:188  0:000  score candidate at 399F
64:188  0:000  score inserted in acpi_cpu_score _PR_
64:188  0:000  Found ACPI CPU: P000 | P001 | P002 | P003 | P004 | P005 | P006 | P007 | P008 | P009 | P00A | P00B | P00C | P00D | P00E | P00F , within the score: _PR_
64:188  0:000  Found PCIROOTUID = 0
64:188  0:000  Start RTC Fix
64:188  0:000  Start TMR Fix
64:188  0:000  Start PIC Fix
64:188  0:000  PIC size=2B at 27C3
64:188  0:000  found PIC had IRQNoFlag will move -3 bytes
64:188  0:000  Fix Device PIC size -3
64:188  0:000  Start HPET Fix
64:188  0:000  No LPCB device! Patch HPET will not be applied
64:188  0:000  Start Display0 Fix
64:188  0:000  add device GFX0
64:188  0:000  Creating Method(_DSM) for 1002 card
64:188  0:000  now inserting Video device
64:188  0:000  ... into existing bridge
64:188  0:000  patch Display #0 of Vendor=0x1002
64:188  0:000  Start NetWork Fix
64:189  0:000  found NetWork device [0x00010003:2] at 20B0 and Name is POT2
64:189  0:000  NetworkADR1=10003 NetworkADR2=2
64:189  0:000  network DSM created, size=6A
64:189  0:000  Start SBUS Fix PCI=12D0 len=59D5
64:189  0:000  device (SBUS) found at 2852
64:189  0:000  SBUS code size fix = 0x0000005E
64:189  0:000  patch HDEF in DSDT 
64:189  0:000  Start HDA Fix
64:189  0:000  found HDA device NAME(_ADR,0x00080001) And Name is GP18
64:189  0:000  Name GP18 present at 0x27F1, renaming to HDEF
64:189  0:000  Name GP18 present at 0x3935, renaming to HDEF
64:189  0:000  Start HDMI6 Fix
64:189  0:000  have no HDMI device while HDMIADR2=1
64:189  0:000  HDMIADR1=30001 HDMIADR2=1
64:189  0:000    with default properties
64:189  0:000  Start USB Fix
64:189  0:000  USB bridge[10003] at 1E15, size = 529
64:189  0:000  found USB device [00010003:0] at 1E50 and Name was PTXH -> XHC1
64:189  0:000  Name PTXH present at 0x3B, renaming to XHC1
64:189  0:000   found slave _DSM, skip
64:189  0:000  USB bridge[70001] at 278F, size = CB
64:189  0:000  found USB device [00070001:3] at 27C9 and Name was XHC0 -> XHC1
64:189  0:000  Name XHC0 present at 0x3A, renaming to XHC1
64:189  0:000  Start _WAK Return Fix
64:189  0:000  _WAK Method find return data, don't need to patch.
64:189  0:000  return len=5BEC
64:189  0:000   deleting device CRT_
64:190  0:000   deleting device DVI_
64:190  0:000   deleting device SPKR
64:190  0:000   deleting device ECP_
64:190  0:000   deleting device LPT_
64:190  0:000   deleting device FDC0
64:190  0:000   deleting device ECP1
64:190  0:000   deleting device LPT1
64:190  0:000  Name APSS present at 0x3C71, renaming to OPSS
64:190  0:000  Start PNLF Fix
64:190  0:000  found PWRB at 3B2F
64:190  0:000  Start _S3D Fix
64:191  0:000    indirect name=TPMM
64:191  0:000    indirect name=FTPM
64:191  0:000    indirect name=PPIM
64:191  0:000  Start ADP1 fix
64:191  0:000  no device(AC) exists
64:191  0:000  Start Darwin Fix
64:191  0:000  Name _OSI present at 0x307, renaming to OOSI
64:191  0:000  Name _OSI present at 0x30E, renaming to OOSI
64:191  0:000  Name _OSI present at 0x329, renaming to OOSI
64:191  0:000  Name _OSI present at 0x346, renaming to OOSI
64:191  0:000  Name _OSI present at 0x35C, renaming to OOSI
64:191  0:000  Name _OSI present at 0x370, renaming to OOSI
64:191  0:000  Name _OSI present at 0x386, renaming to OOSI
64:191  0:000  Name _OSI present at 0x3A5, renaming to OOSI
64:191  0:000  Name _OSI present at 0x3C4, renaming to OOSI
64:191  0:000  Name _OSI present at 0x3E3, renaming to OOSI
64:191  0:000  Name _OSI present at 0x3FE, renaming to OOSI
64:191  0:000  Name _OSI present at 0x41D, renaming to OOSI
64:191  0:000  Name _OSI present at 0x438, renaming to OOSI
64:191  0:000  Name _OSI present at 0x453, renaming to OOSI
64:191  0:000  Name _OSI present at 0x49C7, renaming to OOSI
64:191  0:000  Name _OSI present at 0x49CE, renaming to OOSI
64:191  0:000  Name _OSI present at 0x49E9, renaming to OOSI
64:191  0:000  Name _OSI present at 0x4A04, renaming to OOSI
64:191  0:000  Start SHUTDOWN Fix len=5C9E
64:191  0:000  === [ ACPIDropTables ] ====================================
64:191  0:000  === [ PatchAllSSDT ] ======================================
64:191  0:000  Patch table: SSDT   len=0x8C4C
64:191  0:000  Patch table: SSDT  AmdTable len=0x18B4
64:191  0:000  Patch table: SSDT  AOD len=0x17E1
64:191  0:000  Patch table: SSDT  FCHZP len=0x24
64:191  0:000  Patch table: SSDT   len=0xF8
64:191  0:000  Patch table: SSDT  CPMCMN len=0x1664
64:191  0:000  Drop tables from Xsdt, SIGN=XXXX TableID= Length=0
64:191  0:000   Xsdt has tables count=18
64:191  0:000  CPUBase=0 and ApicCPUBase=1 ApicCPUNum=16
64:191  0:000  Not an Intel platform: P-States will not be generated !!!
64:191  0:000  GeneratePStates failed: Status=Not Found
64:191  0:000  SSDT with CPU C-States generated successfully
64:191  0:000  === [ RestSetup macOS ] ===================================
64:191  0:000  EdidDiscovered size=128
64:191  0:000  ------- EDID Table
64:191  0:000  000  |  00  FF  FF  FF  FF  FF  FF  00  22  F0
64:191  0:000  010  |  11  28  00  00  00  80  32  12  01  03
64:191  0:000  020  |  80  30  1E  78  EE  CC  A5  A3  57  4A
64:191  0:000  030  |  9C  25  10  50  54  A5  6B  80  81  40
64:191  0:000  040  |  81  80  95  00  A9  00  B3  00  A9  40
64:191  0:000  050  |  01  01  01  01  21  39  90  30  62  1A
64:191  0:000  060  |  27  40  68  B0  36  00  D9  28  11  00
64:191  0:000  070  |  00  1C  00  00  00  FD  00  30  4C  18
64:191  0:000  080  |  53  11  00  0A  20  20  20  20  20  20
64:191  0:000  090  |  00  00  00  FC  00  48  50  20  77  32
64:191  0:000  100  |  32  32  38  68  0A  20  20  20  00  00
64:191  0:000  110  |  00  FF  00  43  5A  51  38  35  30  30
64:191  0:000  120  |  32  51  30  0A  20  20  00  AB
64:191  0:000  ATI injection not set
64:242  0:051   codec not detected
64:242  0:000   RCBA disabled; cannot use it
64:243  0:000  stringlength = 1540
64:243  0:000  CurrentMode: Width=1280 Height=1024
64:243  0:000  Beginning FSInjection
FSInjectionInstall ...
- Our FSI_SIMPLE_FILE_SYSTEM_PROTOCOL installed on handle: D87ADA58
FSInjectionInstall ...
- Our FSI_SIMPLE_FILE_SYSTEM_PROTOCOL installed on handle: D87ADA58
64:265  0:022  Use origin smbios table type 1 guid.
64:277  0:011  Preparing kexts injection for arch=x86_64 from EFI\CLOVER\kexts\Other
64:277  0:000    Extra kext: EFI\CLOVER\kexts\Other\FakeSMC.kext
64:288  0:010    Extra kext: EFI\CLOVER\kexts\Other\HWInfo.kext
64:296  0:008  Preparing kexts injection for arch=x86_64 from EFI\CLOVER\kexts\10.12
64:297  0:001  SetStartupDiskVolume:
64:297  0:000    * Volume: 'macOS'
64:297  0:000    * LoaderPath: '<null string>'
64:297  0:000    * DevPath: macOS
64:297  0:000    * GUID = 7ECA1F23-3573-4172-8FA6-47AF12C65177
64:298  0:000    * efi-boot-device: <array><dict><key>IOMatch</key><dict><key>IOProviderClass</key><string>IOMedia</string><key>IOPropertyMatch</key><dict><key>UUID</key><string>7ECA1F23-3573-4172-8FA6-47AF12C65177</string></dict></dict></dict></array>
64:299  0:000  Custom boot screen not used because entry has unset use graphics
64:300  0:001  Closing log
Link to comment
Share on other sites
Jono4191
Jono4191
Posted
Posted

npci=0x3000 busratio=32 -v and selecting InjectEDID and InjectATI (Futomaki) lets me boot into Sierra but I only can see the Sierra Wallpaper. If I don't press any key, the display will turn into standby after about 3 seconds. I can wake it up by pressing a key, but there is nothing to see except the Sierra wallpaper. I can't see the login screen. Then I entered my password blind, pressed Enter, then I see a part of the desktop (see attached screenshot). There it seems to stop. No cursor, no dock. Only the clock is running, too fast but thats not my biggest problem right now

 

Are you using the RTC Patch in Clover?

FixRTC is enabled in Clover menu.

post-1316889-0-91357500-1496866297_thumb.jpg

post-1316889-0-04818900-1496866399_thumb.jpg

Link to comment
Share on other sites
Gigamaxx
Gigamaxx
Posted
Posted

npci=0x3000 busratio=32 -v and selecting InjectEDID and InjectATI (Futomaki) lets me boot into Sierra but I only can see the Sierra Wallpaper. If I don't press any key, the display will turn into standby after about 3 seconds. I can wake it up by pressing a key, but there is nothing to see except the Sierra wallpaper. I can't see the login screen. Then I entered my password blind, pressed Enter, then I see a part of the desktop (see attached screenshot). There it seems to stop. No cursor, no dock. Only the clock is running, too fast but thats not my biggest problem right nowFixRTC is enabled in Clover menu.

Don't use inject EDID and inject ATI together, try just ATI and add fake ID 0x????1002 or whatever your card ID is. 0x68101002.

 

 

Using both EDID and ATI inject is probably an issue.

Link to comment
Share on other sites
Jono4191
Jono4191
Posted
Posted

Don't use inject EDID and inject ATI together, try just ATI and add fake ID 0x????1002 or whatever your card ID is. 0x68101002.

 

 

Using both EDID and ATI inject is probably an issue.

Gigamaxx, you are a hero! This was the solution! I only selected InjectATI now and it works.

But now I have the next problem. My wireless mouse isn't working :(

  • Like 1
Link to comment
Share on other sites
Gigamaxx
Gigamaxx
Posted
Posted

Gigamaxx, you are a hero! This was the solution! I only selected InjectATI now and it works.But now I have the next problem. My wireless mouse isn't working :(

Welcome to the club, it's always something! If it's Bluetooth good luck, check into the USB fixes.

Link to comment
Share on other sites
gills83
gills83
Posted
Posted

This is what my EFI partition looks like... no nvram.plist

 

Strange thing is that I can see the upper menu bar just random. Often I only see the blurred wallpaper, then it seems to stop

 

debug DSDT attached

:hysterical:

 

no comment

 

goodbye ..... :P

Link to comment
Share on other sites
Jono4191
Jono4191
Posted
Posted

Don't think that this is Bluetooth. It's such a ultra cheap wireless mouse from a local store, noname product.

 

 

USB Fixes? Kexts or what do you mean exactly?

 

 

:hysterical:

 

no comment

 

goodbye ..... :P

Noob-Alert, I know :D

Link to comment
Share on other sites
Gigamaxx
Gigamaxx
Posted
Posted

Don't think that this is Bluetooth. It's such a ultra cheap wireless mouse from a local store, noname product.http://www.ebay.co.uk/itm/ET-D100-Black-2-4GHZ-Wireless-Mouse-for-PC-Computer-Laptop-with-USB-Dongle-/262999339676USB Fixes? Kexts or what do you mean exactly?

I just thought of something, my USB 2.0 stops after boot, try a USB 3.0 port.

Link to comment
Share on other sites
Jono4191
Jono4191
Posted
Posted

I just thought of something, my USB 2.0 stops after boot, try a USB 3.0 port.

None of my USB ports are working except the only two USB 2.0 ports on the back of my PC.

Mouse and keyboard are working now, but how can I fix all the other ports? I disabled the FixUSB option in clover because I got errors while booting "unable to find driver for this platform: \"ACPI\".\n"@/SourceCache/xnu/xnu-2782.40.9/iokit/Kernel/IOPlatformExpert.cpp" something like this. So I unchecked FixUSB and it works

 

And Ethernet isn't working... Gigamaxx, you also have a GA-AB350-Gaming right? How did you get Ethernet to work?

Link to comment
Share on other sites
Gigamaxx
Gigamaxx
Posted
Posted

None of my USB ports are working except the only two USB 2.0 ports on the back of my PC.Mouse and keyboard are working now, but how can I fix all the other ports? I disabled the FixUSB option in clover because I got errors while booting "unable to find driver for this platform: \"ACPI\".\n"@/SourceCache/xnu/xnu-2782.40.9/iokit/Kernel/IOPlatformExpert.cpp" something like this. So I unchecked FixUSB and it worksAnd Ethernet isn't working... Gigamaxx, you also have a GA-AB350-Gaming right? How did you get Ethernet to work?

Find the 8111g kext using search and add it to S/L/Extensions and make sure to run kext wizzard. You could also use Pandora and xerxe to add it. I had issues with wifi crashing using the Ethernet fix and wifi I think on my Atheros wifi. The Broadcom wifi has been ok though.. The USB fix you should look for Clover USB patches that go in Kernel and Kext patches section. I'm not home so I can't send my patch till later. I think I'm using USB raise port limit patch, it's pretty common use search tool. It's pretty cool to have USB 3.1 and 3.0 working. 3.1 is new for Apple and High Sierra is supposed to support 3.1 A and C types (thunderbolt) so we shall see.

Link to comment
Share on other sites
Jono4191
Jono4191
Posted
Posted

Find the 8111g kext using search and add it to S/L/Extensions and make sure to run kext wizzard. You could also use Pandora and xerxe to add it. I had issues with wifi crashing using the Ethernet fix and wifi I think on my Atheros wifi. The Broadcom wifi has been ok though.. The USB fix you should look for Clover USB patches that go in Kernel and Kext patches section. I'm not home so I can't send my patch till later. I think I'm using USB raise port limit patch, it's pretty common use search tool. It's pretty cool to have USB 3.1 and 3.0 working. 3.1 is new for Apple and High Sierra is supposed to support 3.1 A and C types (thunderbolt) so we shall see.

Ethernet working fine now, also Audio. Three things are left to be fixed.

 

1. USB Ports

2. System clock is running a bit too fast

3. The system suddenly powered off itself after some minutes. This happend three times now...

Link to comment
Share on other sites
Gigamaxx
Gigamaxx
Posted
Posted

Having struggled to find anything useful, what exactly is happening when booting via Clover UEFI, it prints its line of "++++" and then drops monitor sync and reboots?

 

Kernel almost loading, reboot panic.     Post your System info in your signature please it makes it a little easier to help diagnose.   It also gives someone following with similar build specs to find or give solutions.

 

Boot Arg.=?     

Link to comment
Share on other sites
Nameless One
Nameless One
Posted
Posted

Hardware now in signature, and and what should be the original config.plist from my original successful install but which won't successfully boot my current attempt is attached, I am currently using the 10.12.4_auto kernel but I have tried others including whatever is the RyzenPatcher default, Sierra is at version 10.12.5

 

boot args=-v nvda_drv=1 busratio=30 fsb=100 kext-dev-mode=1 rootless=0 npci=0x2000 slide=0

config.zip

Link to comment
Share on other sites
Gigamaxx
Gigamaxx
Posted
Posted

Hardware now in signature, and and what should be the original config.plist from my original successful install but which won't successfully boot my current attempt is attached, I am currently using the 10.12.4_auto kernel but I have tried others including whatever is the RyzenPatcher default, Sierra is at version 10.12.5

 

boot args=-v nvda_drv=1 busratio=30 fsb=100 kext-dev-mode=1 rootless=0 npci=0x2000 slide=0

 

Try this, I noticed the inject Nvidia at the same time as Web drivers, this maybe one problem.    Changed boot arguments too and Pstates and Cstates.

config.plist.zip

Link to comment
Share on other sites
 Share
Go to topic listing
×
×
  • Create New...