suleiman Posted September 1, 2005 Share Posted September 1, 2005 cyrana, I'm feeling your pain man. My dell D610 has a smooth and fast OS X installation on it, but the only problem is USB doesn't work and neither does wireless. I had another laptop, a compaq with a miniPCI 4306 that *DOES* pick up wireless in OS X. I swapped them into the delll and picked up a wireless card in my OS X install (albeit one that wouldn't turn on??) but nevertheless had to swap them back, as the Compaq (read: HP) laptop wouldn't even boot with the dell's BROADCOM miniPCI in it. Simply rediculous... Link to comment Share on other sites More sharing options...
maltloaf Posted September 1, 2005 Share Posted September 1, 2005 another success here guys, inspiron 9100 with a dell truemobile 1350 card in it working perfectly as an airport card.. thanks to everyone. malty Link to comment Share on other sites More sharing options...
Milenco Posted September 1, 2005 Share Posted September 1, 2005 Installing and loading went just fine here, but i cant seem to connect to any network (it doesn't find any too). I tried using the Linksys WPC54G ver1.2 and the Belkin F5D7010. Airport sees the cards, with there correct (almost correct, only the last digit is different) MAC-addresses as well. When i try to connect to my network manually I get the error msg "There was an error joining the Airport network "Mulder". Obviously Mulder isn't an "Airport" network, it's just my Linksys AP. Ive noticed there are more people here with the same problem. Has anyone of those people got it working yet? Link to comment Share on other sites More sharing options...
bonkiebonks Posted September 1, 2005 Share Posted September 1, 2005 another success here guys, inspiron 9100 with a dell truemobile 1350 card in it working perfectly as an airport card.. thanks to everyone. malty <{POST_SNAPBACK}> Did you have to do any alterations before it could work? Link to comment Share on other sites More sharing options...
daSilVetZ Posted September 1, 2005 Share Posted September 1, 2005 Hey, I just went through the whole guide, and got the "loaded succesfully" message at the end, no errors anywhere along the line.. I rebooted, but there is nothing under Netowrk in the sys prefs, I also made sure the settings were right in the BIOS. If my chipset were not supported, would I still be able to go all the way through with no errors as I did? OR should my WiFi be working? Tx. Link to comment Share on other sites More sharing options...
cyrana Posted September 1, 2005 Share Posted September 1, 2005 That probably means your PCMCIA isn't supported (unless you tried a miniPCI card). A kext will load for anyone if it is compiled properly, but won't do anything if the hardware isn't there. Link to comment Share on other sites More sharing options...
Milenco Posted September 1, 2005 Share Posted September 1, 2005 Okay, i puzzled some more and found some interesting things. At first i couldn't connect to any network using Airport, allthought everything else seemed fine (Airport configured and on, card shows up). The problem of not finding any networks is because of platform=pcx86 i believe. When i booted using platform=ACPI everything worked fine, allthough my system is damn slow. Also, when i boot using platform=pcx86 the system runs fast, untill i open up Airport to search for networks. At that point, kernel_task shoots up to 80% CPU time, making my system extremely slow. When i disabled Airport, kernel_task returns to its normal 0.5% CPU time. Are there people who were able to get this driver working with the platform=osx86 command? How is your experience? Edit: Got it fixed by removing the AppleTPMACPI file. Everything is working smooth and wireless now Bottomline is: If your wireless is working fine, but you can't connect to any networks: Try booting your pc without the platform=pcx86 and use the platform=ACPI line Link to comment Share on other sites More sharing options...
philter Posted September 2, 2005 Share Posted September 2, 2005 MSI UB11B ..has anyone gotten this to work? I have this dongle, and it appears on the http://broadcom.rapla.net/ list of broadcom chipsets, but I can't get it to show up in network interfaces screen. My USB is working, I can use usb keyboards/mice, and the dongle is working ...I tested it in windows, but after installing the Airport kext premade and posted in this thread (succssfully loaded), nothing happens when I insert the usb stick. I'm away from my machine right now, but I can post some logs if need be. http://www.msicomputer.com/product/p_spec....UB11B&class=com Link to comment Share on other sites More sharing options...
jthunder Posted September 2, 2005 Share Posted September 2, 2005 I have a WPC54GS linksys card and after copying the AppleAirPort2.kext from the darwin ISO and modifying the permissions on it. It wont load, the message when I type sudo kextload -t /System/Library/Extensions/AppleAirPort2.kext is: kld(): Undefined Symbols: _OSDequeueAtomic _OSEngueueAtomic the Device ID for the card in Profiler is 17184. What else should I try to get this working? Thanks Link to comment Share on other sites More sharing options...
sack Posted September 2, 2005 Share Posted September 2, 2005 @jthunder: proceed with step 6 of lagnats guide ? or download the compiled .kext file Link to comment Share on other sites More sharing options...
suleiman Posted September 2, 2005 Share Posted September 2, 2005 Updates! Allright...I know it's been a long time since I last visited this thread, but since I know you're all dyinggg to know where I am in my quest to get wireless, I've decided to post this thread. I tried cyrana's method of replacing the device ID for the appleairport2 driver (this involved adding one line in the appleairport2.kext from the appleairport3.kext), and surprisingly enough was able to get appleairport2 to load! Unfortunately, although appleairport2 is now loading fine (i checked it out booting with -v), it still fails to pickup a MAC address on boot. Very odd, as I thought if it recognized the device, it would definitely assign it a MAC address. Going into OS X from that obviously didn't yeild detection of any wireless devices, even in system profiler. The GOOD news is that i've now got USB working (deleted that pesky applefpmemdrier.kext file), which means that when I go home today, I should have a working Belkin 7050 USB waiting for me. So I'll plug that in and try the method some other lucky chap in this topic thread had, and see where that takes me. Best of luck to you all! Link to comment Share on other sites More sharing options...
flatlyna Posted September 2, 2005 Share Posted September 2, 2005 @suleiman yeah, I was lucky. After thinking about it some more, I reckon it worked because the Belkin card became en0 which in turn made the mini-pci become en1. Maybe OSX expects the Airport to be en1 because a genuine Apple would always have a nic on en0. Its been working well since it got enabled. Dunno what to do with the Belkin USB, figured I may need it again if I needed to re-install some time! Link to comment Share on other sites More sharing options...
ruolez Posted September 2, 2005 Share Posted September 2, 2005 I am sorry for a stupid question, but where do I get the source code for "foo.c" some was deleted from the first page of this post and I dont know if my Mac OS installation has this file somewhere or do I need to make it? Thanks for all the help! Link to comment Share on other sites More sharing options...
cyrana Posted September 2, 2005 Share Posted September 2, 2005 I am sorry for a stupid question, but where do I get the source code for "foo.c" some was deleted from the first page of this post and I dont know if my Mac OS installation has this file somewhere or do I need to make it? Thanks for all the help! If you'd have read the whole thread you'd have seen all that info on page 5. Although the original instructions do tell you how to do it anyway. Link to comment Share on other sites More sharing options...
ruolez Posted September 2, 2005 Share Posted September 2, 2005 got it, thanks It works, crashed once, but works slow though Link to comment Share on other sites More sharing options...
ianto Posted September 2, 2005 Share Posted September 2, 2005 Wireless cards with ralink chipsets work. My ralink based card is a D-Link DWL-G122(B1) USB dongle and it works. Here is a link to that forum topic: Wireless Cards in OSX <{POST_SNAPBACK}> How did you get this dongle to work? Do you have the deadmoo image. I can load the kext file ok, but when I reboot and insert the usb dongle nothing happens in network preferences.... I have used the cyrana compiled kext. Link to comment Share on other sites More sharing options...
ianto Posted September 2, 2005 Share Posted September 2, 2005 How did you get this dongle to work? Do you have the deadmoo image. I can load the kext file ok, but when I reboot and insert the usb dongle nothing happens in network preferences....I have used the cyrana compiled kext. <{POST_SNAPBACK}> I have a kernel message in the console window now which happens when I insert the usb dongle, and at intervals if it is left in the usb slot. So Im guessing that I have done something wrong? Link to comment Share on other sites More sharing options...
cyrana Posted September 2, 2005 Share Posted September 2, 2005 Just a note to keep this on the topic of airport cards (ie wireless and broadcom chipset). Don't talk about ralink here. Link to comment Share on other sites More sharing options...
devorama Posted September 3, 2005 Share Posted September 3, 2005 Working now! just writing from my room using the wifi. So, for all the acer aspire folks out there: It seems that the application lounch manager (distributed with the laptop itself) takes care of the wifi On/Off switch, the interesting thing is that this switch is somehow hardware and internal, so, by setting the wifi to "Always On" in the lounch manager the wifi will be On even on osx : ) So, using the modified lagnat drivers (thaks so much dude) the ACER aspire 1610 can go on internet via wifi. Andrea <{POST_SNAPBACK}> Dang, I have an Aspire 3000, but I think the Broadcom chipset is 4318. I applied the patch, but it doesn't seem to identify the hardware. This may be a stupid question, but where would it show up? In the System Profiler in Network->Airport Card? Link to comment Share on other sites More sharing options...
preloaded Posted September 3, 2005 Share Posted September 3, 2005 can someone reup the AirPort2.kext or the bz2 file? Link download is expired Link to comment Share on other sites More sharing options...
indokid Posted September 3, 2005 Share Posted September 3, 2005 repost of cyrana's airport2.bz2 http://s25.yousendit.com/d.aspx?id=2VYEAD0...TB1R03QEP56IDWR Link to comment Share on other sites More sharing options...
preloaded Posted September 3, 2005 Share Posted September 3, 2005 repost of cyrana's airport2.bz2 http://s25.yousendit.com/d.aspx?id=2VYEAD0...TB1R03QEP56IDWR <{POST_SNAPBACK}> Thanks! Link to comment Share on other sites More sharing options...
NuhkaX Posted September 3, 2005 Share Posted September 3, 2005 I just got wireless working on my IBM Thinkpad T42 using a Linksys WPC54GS. The GS is the one with SpeedBoost. The Version 1.1 also uses the Broadcom Chipset. I used Cyrana's file and followed the install guide from the post. It's working great. Thanks to everyone that is working hard on getting OSX running on X86!! Link to comment Share on other sites More sharing options...
indokid Posted September 4, 2005 Share Posted September 4, 2005 I just got wireless working on my IBM Thinkpad T42 using a Linksys WPC54GS. The GS is the one with SpeedBoost. The Version 1.1 also uses the Broadcom Chipset. I used Cyrana's file and followed the install guide from the post. It's working great. Thanks to everyone that is working hard on getting OSX running on X86!! <{POST_SNAPBACK}> how do you get it to work???? i have a thinkpad t42 and also the same card wpc54gs i can't boot after installing the loading the airport2.kext as in the instructions Link to comment Share on other sites More sharing options...
indokid Posted September 4, 2005 Share Posted September 4, 2005 how do you get it to work???? i have a thinkpad t42 and also the same card wpc54gs i can't boot after installing the loading the airport2.kext as in the instructions <{POST_SNAPBACK}> god it WORKS!!!!!! i've had this wpc54gs card for like 1.5 weeks now for the first tiem, macos didnt crash at boot and wireless connects thanks to guy who posts his instructions and cyrana for the file Link to comment Share on other sites More sharing options...
Recommended Posts