Jump to content

Intel PRO/100 VE NIC


  • Please log in to reply
329 replies to this topic

#21
pjrf

pjrf

    InsanelyMac Protégé

  • Members
  • Pip
  • 7 posts

>> At First write down your device ID and vender ID.
>> Now open Terminal.app and type in the following line and press Enter key.

sudo vi /System/Library/Extensions/IONetworkingFamily.kext/Contents/PlugIns/AppleIntel8255x.kext/Contents/Info.plist
>> you will be prompted to enter your password. do it.
>> press 'J' key to move down your cursor and you will find something like the following.
<key>IOPCIMatch</key>
<string>0x10518086 0x10508086 0x10298086 0x10308086&amp;0xfff0ffff 0x12098086 0x12278086 0x12288086 0x12298086 0x24498086 0x24598086 0x245d8086 0x10918086 0x10608086&amp;0xfff0ffff</string>
>> In vi mode you can move your cursor up and down, or right and left using J(down), K(up), H(left) and L(right) keys.
>> insert your device ID and venderID somewhere else. mine is 0x10928086, eg, my deviceID is 1092 and venderID is 8086.
>> to insert, press 'I' key and now you are in inserting mode, now write your ID. If done, then press 'ESC' key to exit from inserting mode.
>> If all went good, its time to save. write ':wq!' to save and exit vi mode.
>> if something went wrong, use 'X' key to delete letters or write ':q!' to quit vi mode unsaved.
>> now, write the following line on Terminal.app to clear kext cache.
rm /System/Library/Extensions.*
>> Quit the Termunal.app.
>> Open DiskUtility, and perform permission repair.
>> Reboot your machine.



Thanks! Work for me :)

#22
acidnine

acidnine

    InsanelyMac Protégé

  • Members
  • PipPip
  • 97 posts
  • Location:Buffalo, MN
where are the instructions for the kext?

#23
Rammjet

Rammjet

    InsanelyMac V.I.P.

  • Gurus
  • 5,302 posts
  • Gender:Male

where are the instructions for the kext?

It looks like if you look at the posting right before this one, the instructions are quoted.

Otherwise, if you start at the beginning of the thread, they seem to appear in posting #2.


YFI

#24
MikhaiL

MikhaiL

    InsanelyMac Protégé

  • Members
  • Pip
  • 11 posts
hi - i do not understand where exactly to insert my device and vendor id, lucky enough my id's are exactly the same as in the 2nd post. how would the line look like after everything is edited using the original method. Please help me because i did this and also installed the driver and it still doesnt work, unfortunately i still have my Ethernet greyed out - please please help - i am using 4.6 version of osx86

#25
Rammjet

Rammjet

    InsanelyMac V.I.P.

  • Gurus
  • 5,302 posts
  • Gender:Male
This is supposedly what is in the info.plist:

<key>IOPCIMatch</key>
<string>0x10518086 0x10508086 0x10298086 0x10308086&0xfff0ffff 0x12098086 0x12278086 0x12288086 0x12298086 0x24498086 0x24598086 0x245d8086 0x10918086 0x10608086&0xfff0ffff</string>

If your vendor/device id string is: 0x10928086, then the result would look like this:

<key>IOPCIMatch</key>
<string>0x10928086 0x10518086 0x10508086 0x10298086 0x10308086&0xfff0ffff 0x12098086 0x12278086 0x12288086 0x12298086 0x24498086 0x24598086 0x245d8086 0x10918086 0x10608086&0xfff0ffff</string>



#26
-=LP=-

-=LP=-

    InsanelyMac Protégé

  • Members
  • Pip
  • 8 posts

>> At First write down your device ID and vender ID.
>> Now open Terminal.app and type in the following line and press Enter key.

sudo vi /System/Library/Extensions/IONetworkingFamily.kext/Contents/PlugIns/AppleIntel8255x.kext/Contents/Info.plist

>> you will be prompted to enter your password. do it.

>> press 'J' key to move down your cursor and you will find something like the following.

<key>IOPCIMatch</key>
<string>0x10518086 0x10508086 0x10298086 0x10308086&amp;0xfff0ffff 0x12098086 0x12278086 0x12288086 0x12298086 0x24498086 0x24598086 0x245d8086 0x10918086 0x10608086&amp;0xfff0ffff</string>

>> In vi mode you can move your cursor up and down, or right and left using J(down), K(up), H(left) and L(right) keys.

>> insert your device ID and venderID somewhere else. mine is 0x10928086, eg, my deviceID is 1092 and venderID is 8086.
>> to insert, press 'I' key and now you are in inserting mode, now write your ID. If done, then press 'ESC' key to exit from inserting mode.
>> If all went good, its time to save. write ':wq!' to save and exit vi mode.
>> if something went wrong, use 'X' key to delete letters or write ':q!' to quit vi mode unsaved.

>> now, write the following line on Terminal.app to clear kext cache.

rm /System/Library/Extensions.*

>> Quit the Termunal.app.
>> Open DiskUtility, and perform permission repair.
>> Reboot your machine.



Thanks cloudy. This tip works fine on my config.
I've got a notebook HP dv1740 with Intel Pro/100 VE.
But my WLAN (Broacom 802.11b/g WLAN) and my sound card are not working (Conexant HD).
Please let me know if someone have a tip about these hardware.

-=LP=-

#27
jacksont123

jacksont123

    InsanelyMac Geek

  • Members
  • PipPipPip
  • 117 posts

This is supposedly what is in the info.plist:

<key>IOPCIMatch</key>
<string>0x10518086 0x10508086 0x10298086 0x10308086&0xfff0ffff 0x12098086 0x12278086 0x12288086 0x12298086 0x24498086 0x24598086 0x245d8086 0x10918086 0x10608086&0xfff0ffff</string>

If your vendor/device id string is: 0x10928086, then the result would look like this:

<key>IOPCIMatch</key>
<string>0x10928086 0x10518086 0x10508086 0x10298086 0x10308086&0xfff0ffff 0x12098086 0x12278086 0x12288086 0x12298086 0x24498086 0x24598086 0x245d8086 0x10918086 0x10608086&0xfff0ffff</string>


Rammjet, did you get your Intel Pro/100 Lan working with those device and vendor ids? If so, can you tell me which OS version you are using and can you send me that kext? I also have the same vendor and device id.

#28
goodwiz

goodwiz

    InsanelyMac Protégé

  • Members
  • Pip
  • 38 posts
I have a Intel PRO/100 VE NIC with like vendorID 1092 et like deviceID 8086.
I did everything like Catracho except: " >> now, write the following line on Terminal.app to clear kext cache. "

I don't understand this sentence!! (probably because Ispeak french)

I followed the procedure but no enjoy!!

help me please!

#29
madmp3zz

madmp3zz

    InsanelyMac Protégé

  • Just Joined
  • Pip
  • 1 posts
It's odd, I had mine working in version 10.4.3 but I updated to 10.4.8 and now it dosn't see it at all.

I tried doing whats list and keep getting this message..
when I do the following I get this error...

sudo kextload -v /System/Library/Extensions/AppleIntel8255x.kext
not a bundle file
can't add kernel (run kextload on this kext with -t for diagnostic output)


What does [manually load kext] mean?
I tried to copy and paste it like the 1st to lines.

Edited by madmp3zz, 12 February 2007 - 01:42 AM.


#30
MsockoR

MsockoR

    InsanelyMac Protégé

  • Members
  • Pip
  • 13 posts

It's odd, I had mine working in version 10.4.3 but I updated to 10.4.8 and now it dosn't see it at all.

I tried doing whats list and keep getting this message..
when I do the following I get this error...

sudo kextload -v /System/Library/Extensions/AppleIntel8255x.kext
not a bundle file
can't add kernel (run kextload on this kext with -t for diagnostic output)
What does [manually load kext] mean?
I tried to copy and paste it like the 1st to lines.


i have the exact same problem here also.

#31
MsockoR

MsockoR

    InsanelyMac Protégé

  • Members
  • Pip
  • 13 posts
i reinstalled 10.4.8 and implemented what the first couple posts said to do and it worked.

#32
sansblog

sansblog

    InsanelyMac Protégé

  • Members
  • Pip
  • 6 posts

I have a Intel PRO/100 VE NIC with like vendorID 1092 et like deviceID 8086.
I did everything like Catracho except: " >> now, write the following line on Terminal.app to clear kext cache. "

I don't understand this sentence!! (probably because Ispeak french)

I followed the procedure but no enjoy!!

help me please!


Ca veut dire que tu dois taper:
sudo rm /System/Library/Extensions.*

sudo = super utilisateur excute (do =faire) si tu le fais sans sudo, tu as des messages d'erreurs: tu n'as pas les autorisations.
Ton pb vient peut tre du fait que tu suis les instructions sans bien comprendre ce qu'elles veulent dire.

Id did everything mentionned above.

i'm running 10.4.6 and my ethernet adaptor is red (cable not connected) instead of green.
As this cable runs pretty well under Linux on same board,

My Dev is 27DC an Ven is 8086 so I wrote
<string>0x27DC8086 0x10508086 0x10298086 0x10308086&amp;0xfff0ffff 0x12098086 0x12278086 0x12288086 0x12298086 0x24498086 0x24598086 0x245d8086 0x10918086 0x10608086&amp;0xfff0ffff</string>

I also trried
<string>0x27DC8086 0x10508086 0x10298086 0x10308086&amp;0xffffffff 0x12098086 0x12278086 0x12288086 0x12298086 0x24498086 0x24598086 0x245d8086 0x10918086 0x10608086&amp;0xfff0ffff</string>

but it always says "cable not connected"

I cleared kext cache and did
Open DiskUtility, and performed permission repair.

Have you any idea ?
Firewire connection is working so I can share folders, but I cannot browse the internet.

#33
sandr

sandr

    InsanelyMac Protégé

  • Members
  • PipPip
  • 82 posts
  • Gender:Male
  • Location:Moscow, RUS
In Jas 10.4.8 (V1)
my nic Intel Pro/100+ (82559 chip) not worked ;)
Device ID: VEN_8086 DEV_1229

after install AppleIntel8255x.kext
and first reboot Nic work but after second reboot

system warn "The system extension AppleIntel8255x.kext .... was installed improperly and cannot be used."

i try again replace kext, repair permission and reboot - Nic not worked :)

Attached Files

  • Attached File  1.gif   10.8KB   228 downloads
  • Attached File  2.gif   4.13KB   210 downloads

Edited by sandr, 03 March 2007 - 05:32 PM.


#34
cmm3

cmm3

    InsanelyMac Protégé

  • Members
  • Pip
  • 16 posts

Hi, i hope someone can help me, i have a laptop vaio PCG-V505MFP i installed MAC OS X 10.4.5, everything works fine, but the network card have some problems, the system detects my card but when i plugged in the cable the network preferences show me some bugs like "The cable for Built-in Ethernet is not plugged in". Then few seconds later this messega display "The cable for built in-Ethernet is connected, but your computer does not have an IP adress and cannot connect to the internet", then other few seconds, appears this "Built-in Ethernet is currently active. Built-in Ethernet has a self-assigned IP adress and may not be able to connect to the internet". then other message "Built-in Ethernet is currently active an has the IP adress (my IP adress number). You are connected to the internet via Built-in Ethernet." And all these messages appears many times like my wired will disconnected or something like that but don't, and i try every method i found modiied the AppleIntel8255x.kext, the tulip.kext, i do everything but those messages still apearing.

I hope someone could help me.

Pentium 4 mobile 2.2Ghz 400MhzFSB
512MB RAM
ATI Mobility Radeon 16MB
40 G.B. Hard Disk
Network card: Intel PRO/100 VE
Wireless: LAN Express as miniPCI 802./b/g



i am having a similar issue w\ my VAIO V505-GC2 whihc is almost identical in specs. Ethernet status goes from green to yEllow to red and back to green, to, yellow , to red every few seconds. i have only been able to get as far as my router's config page in my web browsers and this takes literally 2 and a half minutes or more to get to the username and password prompt. forget about actually serfing the web -- it is impossible.

PINGS to my router usually have beween 30 and 60% loss, although obviosuly this means that some packets are succcessfully making the round trip. weird!

i know you posted this a few months back, but i'm wondering if u made any prrogress w\ this issue. i'm afraid to say i havn't and its very frustrating.

thanks in advance for taking the time to reply.

CMM.


PS - i also don't have usb2 support (and dont think i have firewire support either tho i have never tried this as i have no firewire peripherals. i think my lack of usb2 support and the weird duplexing isues i am gaving w\ he Intel pro 100 ve NIC are somehow related. to be clear usb1.0 (and i think 1.1) work just fine.

would love to hear how things are going for ya.

#35
cburston

cburston

    InsanelyMac Protégé

  • Just Joined
  • Pip
  • 3 posts

i have the exact same problem here also.

sudo kextload -v /System/Library/Extensions/AppleIntel8255x.kext
not a bundle file
can't add kernel (run kextload on this kext with -t for diagnostic output)


I have the exactttt same problemmm..anyone help?

Edited by cburston, 10 March 2007 - 04:51 PM.


#36
daviduco

daviduco

    InsanelyMac Protégé

  • Members
  • Pip
  • 23 posts
  • Location:Madrid

sudo kextload -v /System/Library/Extensions/AppleIntel8255x.kext
not a bundle file
can't add kernel (run kextload on this kext with -t for diagnostic output)


I have the exactttt same problemmm..anyone help?


Same here.

I don't mind if my sound card doesn't work, but network is essential.

Some help would be much appreciated.

EDIT

Well, ive done it with. Ive just followed the second post in this topic... niiiceeee.

Edited by daviduco, 17 March 2007 - 07:58 PM.


#37
toca

toca

    InsanelyMac Protégé

  • Members
  • Pip
  • 6 posts
How Would One Go About For Intel Pro 1000pl???? A Few People Said It Worked Out Of The Box But For Me It hasnt been anything but pain.

Running OSX 10.4.8 on toshiba satellite p100
Network DEV/VEN: 109A 8086

Using IONetwork package AppleIntel8524(something like that)


Any help would be appreciated

#38
daviduco

daviduco

    InsanelyMac Protégé

  • Members
  • Pip
  • 23 posts
  • Location:Madrid

How Would One Go About For Intel Pro 1000pl???? A Few People Said It Worked Out Of The Box But For Me It hasnt been anything but pain.

Running OSX 10.4.8 on toshiba satellite p100
Network DEV/VEN: 109A 8086

Using IONetwork package AppleIntel8524(something like that)


Any help would be appreciated


Do what's said at #2 post in this topic for your device .kext folder

#39
y0jeremy

y0jeremy

    InsanelyMac Protégé

  • Just Joined
  • Pip
  • 2 posts
I also have an Intel Pro VE/100 - with 1092 8086. But can not get it working. I've tried everything here. It's on a Toshiba A105-4094 laptop. I've tried importing these kexts's and also get the same errors. anyone know any more options? I'm running 10.4.8 .

#40
lentiflo13

lentiflo13

    InsanelyMac Protégé

  • Members
  • Pip
  • 5 posts
I am trying to do this for the Intel PRO/1000GT

devid is 107c
vendor = 8086.
82541 chipset

So I added 0x107c80856 to the AppleIntel8254XEthernet.kext, Info.plist file,
no such luck still.

Did all repair permissions steps as above and many reboots.

Has anyone here gotten this to work?





2 user(s) are reading this topic

0 members, 2 guests, 0 anonymous users

© 2014 InsanelyMac  |   News  |   Forum  |   Downloads  |   OSx86 Wiki  |   Mac Netbook  |   PHP hosting by CatN  |   Designed by Ed Gain  |   Logo by irfan  |   Privacy Policy