OpenCore General Discussion

[nmano]

On 2/7/2020 at 6:59 AM, Matgen84 said:

Hi All guys

 

Since I add a Broadcom card to my Z390 Aorus master config, I can't boot. Reset Nvram in Picker ---> no success

 

Please, help me

 

 

 

 

 

opencore-2020-02-07-144848.txt

If your card worked before clover.

Give me detail about kext, patch

[ameenjuz]

when I boot latest builded opencore then this issue is appear on boot screen  

OC: configuration requires vault but no vault provided

any know how to fix it

I couldn't create vault.plist

[jinbingmao]

57 minutes ago, anmool said:

when I boot latest builded opencore then this issue is appear on boot screen  

OC: configuration requires vault but no vault provided

any know how to fix it

I couldn't create vault.plist

Vault=Optional

[ameenjuz]

1 minute ago, jinbingmao said:

Vault=Optional

how to fix it OC: configuration requires vault but no vault provided

my boot is stuck with this

[canyondust]

1 hour ago, anmool said:

how to fix it OC: configuration requires vault but no vault provided

my boot is stuck with this

Literally, set the ‘vault’ parameter in config.plist to ‘optional’

[ameenjuz]

1 hour ago, canyondust said:

Literally, set the ‘vault’ parameter in config.plist to ‘optional’

thanks man worked

[mathew2019]

Booting stuck on PCI configuration end and apfs_module_Start:1683....

 

My configuration is i9 10940X + X299 Asus Prime deluxe II motherboard + Radeon VII graphics. I am able to boot with clover but on open core booting is stuck on PCI configuration end + apfs_module_Start:1683....

 

I have tested  OC on my other i9 9900K +z390 motherboard system and it works well 

 

Do I need to add any quirks or any tweaks for X299? I have TSC sync kext for 14core is already added.

 

Any help appreciated

 

Thank you

 

Edited February 9, 2020 by mathew2019

[Matgen84]

On 2/8/2020 at 2:24 PM, nmano said:

If your card worked before clover.

Give me detail about kext, patch

 

It's a OOB wifi card no kexts needed. I think it's a NVRAM issue, my config is very unstable on OpenCore : after clear CMOS, i can boot via Opencore 0.5.5. Since I update to Opencore 0.5.6 Beta, I can't.

 

Config.plist in attachment

 

 

OC-config.plist

[telepati]

@Matgen84 any verbose screen? 

 

I checked your config.plist. First, of all, you don't need these ACPI patches you are already using WEG. Remove all. Also, add AWAC.aml and checksum RTC patch. No need to set ProtectSecureBoot quirks YES. Make this NO.

Edited February 9, 2020 by telepati

[startergo]

On 2/8/2020 at 8:10 AM, nmano said:

9 ACPI Sleep patch

9 ACPI patch for sleep config-OC.plist  All Intel Motherboard. I test X99,X299.

 

 

Is this doing the same as HibernationFixup.kext?

[nmano]

3 hours ago, startergo said:

Is this doing the same as HibernationFixup.kext?

Test1-with  HibernationFixup.kext

Test2-with  HibernationFixup.kext + patch

test3-Just patch

Restart your System each time.

 

Edited February 9, 2020 by nmano

[telepati]

@vit9696 You are confusing me. You are saying do not use AppleUsbKbDxe.efi Ivy Bridge (3rd generation Core) and above motherboards. But if I am not using it on my TUF Z390 Hotkeys are doesn't work.

I am using these settings and just Alt/Opt, Command+V Command+S etc. working but Command+R and Command+Opt+P+R unusable.

 

PollAppleHotKeys YES

ShowPicker NO

TakeoffDelay 5000

Timeout 0

UsePicker YES

KeySupport YES

 

If I add AppleUsbKbDxe.efi and set KeySupport NO all Hotkeys are working without any problem.

What should we do now are we using this efi driver or not?

 

Note: I am using Apple Numerical Wired Keyboard.

Edited February 10, 2020 by telepati

[canyondust]

20 minutes ago, telepati said:

@vit9696 You are confusing me. You are saying do not use AppleUsbKbDxe.efi Ivy Bridge (3rd generation Core) and above motherboards. But if I am not using it on my TUF Z390 Hotkeys are doesn't work.

I am using these settings and just Alt/Opt, Command+V Command+S etc. working but Command+R and Command+Opt+P+R unusable.

 

PollAppleHotKeys YES

ShowPicker NO

TakeoffDelay 5000

Timeout 0

UsePicker YES

KeySupport YES

 

If I add AppleUsbKbDxe.efi and set KeySupport NO all Hotkeys are working without any problem.

What should we do now are we using this efi driver or not?

 

Note: I am using Apple Numerical Wired Keyboard.

I’m on Z170 and exhibit the same behavior, but mine does work within a very small time window. I have to press the hot keys within about 100ms of the bios logo disappearing. I’m also on an Apple numerical wired keyboard. 

[telepati]

39 minutes ago, canyondust said:

I’m on Z170 and exhibit the same behavior, but mine does work within a very small time window. I have to press the hot keys within about 100ms of the bios logo disappearing. I’m also on an Apple numerical wired keyboard. 

Are you holding or repeatedly press? Cause I tried both it never worked.

 

But with AppleUsbKbDxe.efi its working like a crazy.

Edited February 10, 2020 by telepati

[canyondust]

23 minutes ago, telepati said:

@vit9696 You are confusing me. You are saying do not use AppleUsbKbDxe.efi Ivy Bridge (3rd generation Core) and above motherboards. But if I am not using it on my TUF Z390 Hotkeys are doesn't work.

I am using these settings and just Alt/Opt, Command+V Command+S etc. working but Command+R and Command+Opt+P+R unusable.

 

PollAppleHotKeys YES

ShowPicker NO

TakeoffDelay 5000

Timeout 0

UsePicker YES

KeySupport YES

 

If I add AppleUsbKbDxe.efi and set KeySupport NO all Hotkeys are working without any problem.

What should we do now are we using this efi driver or not?

 

Note: I am using Apple Numerical Wired Keyboard.

I’m on Z170 and exhibit the same behavior, but mine does work within a very small time window. I have to press the hot keys within about 100ms of the bios logo disappearing. I’m also on an Apple numerical wired keyboard. 

[canyondust]

1 hour ago, telepati said:

Are you holding or repeatedly press? Cause I tried both it never worked.

 

But with AppleUsbKbDxe.efi its working like a crazy.

I’ve been able to do it both was. Timing of the press is the most critical. I’m going to try messing with takeoff delay values and switch the protocol from auto to AMI. AppleUsbKbDxe also works perfectly for me but I’m trying not to use it.

[Matgen84]

13 hours ago, telepati said:

@Matgen84 any verbose screen? 

 

I checked your config.plist. First, of all, you don't need these ACPI patches you are already using WEG. Remove all. Also, add AWAC.aml and checksum RTC patch. No need to set ProtectSecureBoot quirks YES. Make this NO.

 

Thanks. I can boot but with Black Screen instead of macOS Desktop!  How to find verbose screen?

[telepati]

2 hours ago, Matgen84 said:

 

Thanks. I can boot but with Black Screen instead of macOS Desktop!  How to find verbose screen?

Add boot-argument -v

 

I checked again you already have it. But remove those boot arg;

 

slide=255 agdpmod=pikera darkwake=8

Edited February 10, 2020 by telepati

[Matgen84]

1 hour ago, telepati said:

Add boot-argument -v

 

I checked again you already have it. But remove those boot arg;

 

slide=255 agdpmod=pikera darkwake=8

 

I try and let you know. Thanks.

 

 

Edit: @telepati

 

It seems to work now (thanks for your advice on patches). In verbose mode, I see several ACPI error. I have to find the file to find out more 

Edited February 10, 2020 by Matgen84

[canyondust]

14 hours ago, telepati said:

Are you holding or repeatedly press? Cause I tried both it never worked.

 

But with AppleUsbKbDxe.efi its working like a crazy.

 

Update: I've switched the KeySupportMode to AMI and it seems i have to wait to press the keys until after the BIOS splash screen to disappear (Gigabyte Z170). I press and hold. Both book picker via opt and verbose mode tested and work fine this way, and even am able to wait around 1sec after the bios splash screen disappears to get the hotkeys working. (0.5.5 release)

Hope that helps!

[texem]

Kexts are going to be deprecated , what does this mean for OC ?

 

 

 

[mhaeuser]

@texem from what we are aware of, nothing. Apple still is going to use kexts for themselves (as iOS does), and we smuggle ours into just the same place ahead of any macOS logic running

[telepati]

3 hours ago, canyondust said:

 

Update: I've switched the KeySupportMode to AMI and it seems i have to wait to press the keys until after the BIOS splash screen to disappear (Gigabyte Z170). I press and hold. Both book picker via opt and verbose mode tested and work fine this way, and even am able to wait around 1sec after the bios splash screen disappears to get the hotkeys working. (0.5.5 release)

Hope that helps!

If you don't mind could you please share your config.plist I want to compare with mine.

 

BTW is your timeout set 0 or 5? To be sure set 0 then try is it still working or not?

 

I tried Auto and AMI too with timeout 0 it's never working. It always boots with the default drivers. Also set TakeOffDelay 5.000 and 10.000 but it never helped either. For me best options looks like AppleUsbKbDxe.efi. With this efi works like a real make. I don't even think when I must press its always accurate and its always working. 

 

I attached my config.plist.

 

config.plist

Edited February 10, 2020 by telepati

[mathew2019]

Why I am getting these errors when I use latest OC V5.5, the booting is stuck on this screen. OC 5.4 is working fine.

[Pavo]

39 minutes ago, mathew2019 said:

Why I am getting these errors when I use latest OC V5.5, the booting is stuck on this screen. OC 5.4 is working fine.

Looks like you missed quite of few updates to the config, compare yours to the newer Sample.plist