aqua-mac Posted July 16, 2008 Share Posted July 16, 2008 Well I just had to respond to the fabulous effort by TorqueX86 in his G5 case! Here are the first 2 shots of how far I have got, the back panel is still to be sorted, but you are looking at a full size ATX Asus P5E3 Premium Wireless @ n motherboard in a Mac Pro case!! How did I get it in you ask yourself and keep the shelf and HDD's in tact? I will reveal all at the weekend when I have a little more time. The sockets still need some work at the back but this time all the original Apple positions will hopefully be used. The front panel/power button is 100% functional and all original Mac Pro fans have been used but are controlled by the motherboard and revolve very slowly and are fully adjustable from the bios on this motherboard. It is virtually silent but is Quad powered at 3.6 GHz 1333 corsair DDR3 and has dual Nvidia 9800 GTX's! I am so enjoying the power, I don't want to have to take it apart again to wire up the back sockets! Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/ Share on other sites More sharing options...
vbetts Posted July 16, 2008 Share Posted July 16, 2008 That is one sharp Mac Pro case mod you've got there... Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-821805 Share on other sites More sharing options...
MacBookJoe Posted July 16, 2008 Share Posted July 16, 2008 That looks unreal!!!..... I'm still yet to move mine along that far... cash is still very tight... Look forward to seeing how much room was required behind the shelf.. did you re-crimp the fan cables to make them fit on the Mobo? with both GFX cards in do you still can full access to all four hard drive bays? Very very impressive Aqua-mac. J. Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-821912 Share on other sites More sharing options...
aqua-mac Posted July 16, 2008 Author Share Posted July 16, 2008 Yup all hard drives are accessible - all fan cables were rewired to fit 3 Pin PC fan outlets. Took some time to work out the wiring though. The very top PCI slot is not usable but both 16 x PCIe slots and the first PCI slot are fine. The secret was to cut a slot in the bottom of the case to let the motherboard drop down by about 4 mm. This allowed all the slots to line up! I am in the process of milling an aluminium cover for that will fix with socket screws on the underside. I will probably make it perforated too to aid cooling. Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-821927 Share on other sites More sharing options...
Daft_Punk Posted July 17, 2008 Share Posted July 17, 2008 holy {censored} aquamac, thats some skill. if insanelymac was like facebook, i would give u a gift entitled "OSx86 God, this gift makes the owner pwn all" Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-822078 Share on other sites More sharing options...
aqua-mac Posted July 17, 2008 Author Share Posted July 17, 2008 Thanks for the comments guys. Still a little work to do on this but nearly there. Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-822186 Share on other sites More sharing options...
(MoC) Posted July 17, 2008 Share Posted July 17, 2008 Thanks for the comments guys. Still a little work to do on this but nearly there. Nice mod man, kudos. I'm looking forward to doing something similar for a friend. Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-822193 Share on other sites More sharing options...
stellarola Posted July 17, 2008 Share Posted July 17, 2008 Looks really good Aqua-Mac. I need to take my time with my next Hackintosh so I can get similar results to you and TorqueX86. Congrats and keep up the great work! -Stell Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-822284 Share on other sites More sharing options...
MacBookJoe Posted July 17, 2008 Share Posted July 17, 2008 So did you have to cut both the shelf and the bottom of the case? I had just about pulled myself away from my MacPro mod... saw this and have been sucked back in! how are you doing the rear IO plate? I've been drawing up a frame that will allow for my motherboard supplied IO plate to clip in.. couple engineers at work a moaning about it.. :-p J. Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-822516 Share on other sites More sharing options...
fatshitcat Posted July 17, 2008 Share Posted July 17, 2008 :drooling: Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-822542 Share on other sites More sharing options...
TorqueX86 Posted July 17, 2008 Share Posted July 17, 2008 Sexy! I didn't actually know you could fit a full ATX *and* keep the 4 HD on the mac pro case! Thsi is really sweet! Can you explain in detail how you crammed it all inside? SUper job, I think I'll do one myself next year! Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-822789 Share on other sites More sharing options...
aqua-mac Posted July 17, 2008 Author Share Posted July 17, 2008 Thanks guys. I am not at home at the mo, writing this from a hotel room, but here goes: I did not cut the shelf at all! Basically, I cut a hole in the bottom of the case that allowed the motherboard to hang down by 4 mm. This is enough to align the card slots with the case. It does not have to be a big hole - in fact, it is a 10 mm wide slit that is wider in the middle to accommodate the motherboard lower heat sink. With my board, I only loose the use of the furthest PCI x1 slot at the opposite end - no great problem. The board slots under the HDD fixing rear bracket and does not interfere with it. I have designed a 5 mm thick, aluminium plate to fit over the hole and will perforate it to look like the case front and aid cooling. To be honest, there is no need for the plate as all is hidden unless you turn the case over, but it should look like a std Apple fitment. For the back ports, I will take a leaf out of TorqueX86's book and I am determined to keep the mac openings and fix together 3 USB, FW 800, FW400, optical, dual-lan, mic-in and sound-out just as Apple intended. I will put some more pics up at the weekend showing the slot in the bottom, but I have not finished the bottom cover yet. I used this power supply as it has the power plug in the middle already. I did have to dremmel a bit from around the plug though to drop the plug by 5 mm. This does allow you to get the PS in without total removal of the fan support at the top of the case - but the fan had to go and I dremmeled out the fan grill in the middle of the support to allow the wires through the middle. I also removed the switch and bypassed it! Watch this space and thanks for the encouragement! Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-823028 Share on other sites More sharing options...
JedixJarf Posted July 18, 2008 Share Posted July 18, 2008 Wow aqua, that is amazing. Very beautiful. I am very jealous. *tips hat Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-824454 Share on other sites More sharing options...
aqua-mac Posted July 19, 2008 Author Share Posted July 19, 2008 Here are a few more pics: This one shows how the base was done - A dremel is your friend! This will be covered by an aluminium plate when I have finished it. The back plug on the Hiper power supply: The top of the motherboard up against the shelf. There was still a bit of work to do here as at this point the FW plug could not quite fit. A little bit of dremeling though and I got that up and running. I also recon the Apple Sata plugs will just go in with a bit of fiddling! Here is a pic of the board: Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-825031 Share on other sites More sharing options...
skredii Posted July 19, 2008 Share Posted July 19, 2008 How did you attach the power supply inside the case so it won't fall out when you plug/unplug the cable at the rear of the case ? Gr8 work btw I'm waiting for my GA-G33M-DS2R mb to start the project, because the GA-G33-DS3R won't fit :/ Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-825067 Share on other sites More sharing options...
aqua-mac Posted July 19, 2008 Author Share Posted July 19, 2008 If you look at the picture of the power supply I used above, the socket is already in the middle so I only had to lower it. I cut a thin strip of aluminium and araldited it to the inside of the supply to maintain the original size hole that the plug fits in. The supply itself is screwed to the shelf! Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-825075 Share on other sites More sharing options...
TorqueX86 Posted July 20, 2008 Share Posted July 20, 2008 I have a recommendation and a question: Recommendation: You really ought to place a rubber insulated edge cover around the small opening at the bottom, if by any chance the mobo touches the case you'll cry sour tears... Question: I would like to buy for my case the Mac Pro processor "box", that thingy with the hole where you change the RAMs on a MP, and the left hand side grey plastic cover. Where do I get them, and what price should I expect to pay? Kudos again, I'm all fired up to improve my mod now Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-826066 Share on other sites More sharing options...
aqua-mac Posted July 20, 2008 Author Share Posted July 20, 2008 Hi Torque, All housings were bought from this seller on ebay. I would send them a message to see if they still have the parts you require. As far as insulation is concerned, the rear of the motherboard is insulated with self adhesive rubber strip. This whole area will be covered up soon with an aluminium plate. Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-826146 Share on other sites More sharing options...
dark4181 Posted July 20, 2008 Share Posted July 20, 2008 Aqua, you plainly have too much time and too much money.. My G5 case and all the parts, bits and bobs to mod it have been in my closet since I bought them last year I'm either too busy to get started, or lack the money to begin. One of the two is always going on for me Nonetheless, beautiful Hack Pro Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-826448 Share on other sites More sharing options...
aqua-mac Posted July 20, 2008 Author Share Posted July 20, 2008 Hi Dark, Ha Ha! Saving for the bits is still fairly hard work, but time I have little of. The parts were bought over a period of 3 - 4 months, but other parts were sold to pay for them. I usually do bits in the evenings when I get home from work - but my social life is a bit {censored} at the moment for sure. Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-826506 Share on other sites More sharing options...
TorqueX86 Posted July 21, 2008 Share Posted July 21, 2008 Hi Torque, All housings were bought from this seller on ebay. I would send them a message to see if they still have the parts you require. Hey Aqua, Would you know the product code for the parts I need? If I knew the precise code I might attempt buying them from the local Apple shop where I bought the new G5 case... But I need the part codes, as there is a quite big language barrier, I'm a brit expat living in Asia... Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-827804 Share on other sites More sharing options...
aqua-mac Posted July 21, 2008 Author Share Posted July 21, 2008 Hi Torque, memory cage + rear fan (922-7679) http://www.welovemacs.com/9227679.html Front fan assby (922-7699) Only one fan included. http://www.welovemacs.com/9227699.html Optical Drive Carrier (922-7729) http://www.welovemacs.com/9227729.html HDD Carrier (922-7728) http://www.welovemacs.com/9227728.html Processor cover (922-8527) I think? Not sure about this one. Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-828206 Share on other sites More sharing options...
TorqueX86 Posted July 22, 2008 Share Posted July 22, 2008 Hi Torque, Processor cover (922-8527) I think? Not sure about this one. Ace, Aqua, those are all the parts I need! I'll go have a fight at the Apple store in the weekend and try to bring the sacred metal at home For "processor cover" I meant the aluminium duct attached to the rear fan that you kindly indicated to me. That was awesome Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-828652 Share on other sites More sharing options...
Jedric Posted July 27, 2008 Share Posted July 27, 2008 Torque, Here's all the part # for the MAC PRO courtesy of mac-pro.com Processor cover part # is 922-7710. Which is also what I need. I inquired and its expensive here in Canada about $50 plus tax so i might just have to improvise to fill the gap. Keep up the good work guys. Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-835123 Share on other sites More sharing options...
apowerr Posted July 27, 2008 Share Posted July 27, 2008 Awesome mod man, very clean and professional looking Link to comment https://www.insanelymac.com/forum/topic/116091-mac-pro-mk-ii/#findComment-835185 Share on other sites More sharing options...
Recommended Posts