Jump to content

Mac OS X 10.5.5 Kalyway COMBO UPDATE

zeamp

By zeamp,
in OSx86 10.5 (Leopard)

 Share
62 posts in this topic

Recommended Posts

zeamp
zeamp
Posted
Posted

I have a Dell Inspiron 1525 and myself, and others with similar models have reported kernel panics when going from 10.5.4 Kalyway to 10.5.5 via Software Update. There are a few tips and tricks, some success and some failures, but what is the clear cut method? I'd like any of you Kalyway users to post your success and how you did it on getting 10.5.5 to run without erroring, panicing, or beachball syndrome.

 

Thanks in advance -- POST SCREENSHOTS OF SUCCESS/FAILURE!

Link to comment
Share on other sites
mrmick
mrmick
Posted
Posted

I successfully went from 10.5.3 to 10.5.4 to 10.5.5 incrementally using these files:

 

http://www.apple.com/support/downloads/macosx1054update.html

http://www.apple.com/support/downloads/macosx1055update.html

 

I did NOT use the 10.5.5 ComboUpdate from Apple.

 

The kernel is 9.5. I started with Kalyway 10.5.1 and then did the 10.5.2/.3 Kalyway updates.

 

As far as I can tell, everything still works.

Link to comment
Share on other sites
robert_
robert_
Posted
Posted

updated from kalyway 10.5.3 to 10.5.5 with sleepscript etc. now i wont get to the desktop. it stucks at the grey apple screen. the loading-circle stops and the only thing i can do is to shutdown :(

 

in safe-mode it works, but then my internal keyboard and the touchpad doesnt work :(

 

i plugged an external mouse and keyboard and repaired permission etc. but no success :( still stucking at the grey apple screen.

Link to comment
Share on other sites
GoBx
GoBx
Posted
Posted

On P5W DH mobo.

I started with Kalyway 10.5.1 vanilla kernel + EFI v8

Updated to 10.5.2, 10.5.3, 10.5.4 using netkas method (combo update + background script in terminal)

 

I did the same thing with 10.5.5, but can't boot anymore (It seems it starts to boot, I hear the HD 2-3 seconds, then spinning wheel and finally HDs are turned off).

Guess what ? I had to format my time machine HD this week end so I lose everything

 

Boot with -v shows error message about JMicron

I've tried rd=disk2s1, tried -s then fsck -fy

 

A solution to make me boot again would be VERY appreciated :(

Link to comment
Share on other sites
Arial
Arial
Posted
Posted

my detailed system: http://paste2.org/p/74952

 

Processor  : Intel Core2Duo E6850 @ 3066 MHz
Mainboard  : Abit IP35-E (ICH9, JMicron IDE Controller, Realtek ALC888, Marvell Yukon 88E8056)
Memory	 : DDR2 2x Corsair CM2X1024-6400 1024 MB, 2x A-Data Extreme PC2-6400 512 MB
Display	: ASUS NVidia 8600GT 256MB, SyncMaster 932GW DVI, 1440x900@60Hz
HDD		: WD Raptor 150GB (Windows) on SATA#1, WD 320GB (OSx86) on SATA#2, Seagate 250GB on SATA#5
ODD		: Lite-On DVDRW LH-20A1S on SATA#6, Samsung TSSTcorp DVD-ROM SH-D162C PATA
Mouse-Key  : HP Cordless 2.4GHz
PSU		: FSP BlueStrom II 500W
Case	   : Aerocool S-55
Speaker	: Edifier 2.1
Addon#1	: PCI-to-IDE SiI 0680 Ultra-133 Medley ATA Raid, Samsung 160GB PATA, Maxtor 160GB PATA
Addon#2	: Thermaltake iCage Drive Module
Addon#3	: Huawei E220 HSDPA USB Modem

OS		 : Mac OSx86 Leopard 10.5.5, XP-32 Pro SP3, Vista-32 Ultimate SP1
Bootloader : GRUB4DOS v0.4.3 | http://i36.tinypic.com/fthsw0.jpg

Mac OSx86  : iATKOS 1.0ir3, Kalyway 10.5.1, Kalyway 10.5.2>10.5.5, iDeneb v1.1 10.5.4>10.5.5
		 http://i35.tinypic.com/jzu2h2.png
OSx86 Fix  : MBR Partition Map Scheme | http://i37.tinypic.com/2exrlv7.jpg
		 Kalyway using PC_EFI V8, iDeneb using Chameleon v1.0.11 Boot ROM
		 9.5.0 Vanilla Kernel & System.kext
		 AppleACPIPlatform.kext Reboot Fix
		 PowerOff bug fix.pkg
		 AppleSMBIOS-27 rev.6 by mac.nub
		 AppleIntelPIIXATA.kext fixed for ICHx chipset
		 JMicronATA.kext for JMicron JMB368 IDE Controller
		 NVIDIA GeForce 8600GT 256MB GFX String by OSX86Tools
		 ALCinject.kext & AppleHDA.kext for Realtek HDA ALC888 on ICH9
		 Yukon2.kext for Marvel Yukon 88E8056 Gigabit

 

Kalyway 10.5.2 EFI V8

updated to 10.5.3 with JaS 10.5.3 Combo Update

updated to 10.5.4 with downloaded delta update

updated to 10.5.5 with downloaded delta update and netkas method (remove AppleIntelCPUPowerManagement.kext during update)

 

my screen.. th_2cc4858e.png | th_16176f69.png <--click

 

55d468a0.pnge87b5629.png

Link to comment
Share on other sites
reery
reery
Posted
Posted
I successfully went from 10.5.3 to 10.5.4 to 10.5.5 incrementally using these files:

 

http://www.apple.com/support/downloads/macosx1054update.html

http://www.apple.com/support/downloads/macosx1055update.html

 

I did NOT use the 10.5.5 ComboUpdate from Apple.

 

The kernel is 9.5. I started with Kalyway 10.5.1 and then did the 10.5.2/.3 Kalyway updates.

 

As far as I can tell, everything still works.

 

Hi,

 

I'm right here: Kalyway 10.5.3 with 9.2 sleep-kernel. Updated from 10.5.2 to 10.5.3 with the Kalyway combo-updater - I had to install the kernel after updating.

 

Have you done some post installations after updating to 10.5.4, like reinstalling kernel or so?

Link to comment
Share on other sites
lbaz
lbaz
Posted
Posted

I have an Asus P5W DH that was running kalyway 10.5.4. Downloaded the delta update 10.5.5 with the link provided in this post by mrmick and applied it with the netkas background script in terminal method. The only thing was no sound........erased the kexts for sound and reinstalled with ALC882 AppleHDA v0.4b.mpkg and everything is working perfect with Vanilla kernel. Jmicron is disabled in BIOS.

 

I think its the way to go at least for this MB.

 

Thanks all for the info in this thread it was very helpfull.

 

post-212675-1221765037_thumb.jpg

Link to comment
Share on other sites
tessa17
tessa17
Posted
Posted
I successfully went from 10.5.3 to 10.5.4 to 10.5.5 incrementally using these files:

 

http://www.apple.com/support/downloads/macosx1054update.html

http://www.apple.com/support/downloads/macosx1055update.html

 

I did NOT use the 10.5.5 ComboUpdate from Apple.

 

The kernel is 9.5. I started with Kalyway 10.5.1 and then did the 10.5.2/.3 Kalyway updates.

 

As far as I can tell, everything still works.

 

 

just 1 question did you use the netkas method of installing????? Or did you do you just install it?

Link to comment
Share on other sites
zeamp
zeamp
Posted
  • Author
Posted

For anyone thinking "Hey! There's no Kalyway Combo Update here. What gives?"

 

I successfully upgraded from 10.5.4 Kalyway to 10.5.5. You can find more information on my tutorial.

 

Runs great! Check my signature for specs.

Link to comment
Share on other sites
lbaz
lbaz
Posted
Posted
I will try the combo update later, with my ASUS P5K-E Motherboard.

 

But before I do, has anyone tried it with the same motherboard as me?

 

Use the Delta update link provided by mrmick and netkas method. Do not use software or combo update.

Link to comment
Share on other sites
smcpipint
smcpipint
Posted
Posted

Upgraded using the Netkas method and the 10.5.5 delta upgrade, NOT the combi. No problems on an Asus Maximus Formula (X38/ICH9/JMicron), other than having to reinstall Taruga to get sound back. I did not use the combi as previous combi upgrades have trashed the AHCI kexts; the delta upgrade did not.

Link to comment
Share on other sites
Coloro
Coloro
Posted
Posted

Origin: Kalyway 10.5.2 -> Kalyway Combo Update 10.5.3 (vanilla kernel) -> Software Update's 10.5.4 update.

 

Downloaded delta (not combo) 10.5.5 update.

Started Netkas method on terminal (to recursively delete AppleIntelCPUPowerManagement file).

Started update.

Before completing, alarm! :) My screen turns grey and a message tells me to power off my PC or hard reboot it.

Power on again, and my system gets blocked after a few lines of code on screen: power off again :rolleyes: .

One more power-on, and my PC suddenly autoreboots after a few lines of code on screen.

Starts booting... grey Apple's screen... blue screen... my system is up and running! :angel:

Now 'about this Mac' says my version is 10.5.5, and all (sound, graphics...) works as ever.

I don't know what happened, I am even not sure if my system is really running 10.5.5, but I'm happy :) .

 

Ricardo

Link to comment
Share on other sites
bl003r
bl003r
Posted
Posted
Upgraded using the Netkas method and the 10.5.5 delta upgrade, NOT the combi. No problems on an Asus Maximus Formula (X38/ICH9/JMicron), other than having to reinstall Taruga to get sound back. I did not use the combi as previous combi upgrades have trashed the AHCI kexts; the delta upgrade did not.

 

Did you come from 10.5.4 or from 10.5.3? If you installed from 10.5.4, did you update to 10.5.4 in the same way you describe above?

 

Also can you get the Vanilla kernel to work with your X38 MF because I can't get past 10.5.3 on my system?

 

How do you get the PC to boot with say a Vanilla kernel 9.4.0 or 9.5.0?

Link to comment
Share on other sites
 Mysticus C*
 Mysticus C*
Posted
Posted

You guys can also (alternatively) try my BIKE TOWN FILES and TUTORIAL to update anything to 10.5.5 :P in three stages but at one go...

 

a-) install preparation patch (no restart)

b-) install official update (no terminal fingering needed but no restart yet)

c-) post update patch (custom settings to bring back various files so that no need to worry about more fingering) (restart after this :D )

 

Here is my topic

Link to comment
Share on other sites
smcpipint
smcpipint
Posted
Posted
Did you come from 10.5.4 or from 10.5.3? If you installed from 10.5.4, did you update to 10.5.4 in the same way you describe above?

 

Also can you get the Vanilla kernel to work with your X38 MF because I can't get past 10.5.3 on my system?

 

How do you get the PC to boot with say a Vanilla kernel 9.4.0 or 9.5.0?

 

I came from 10.5.4. And yes, its a vanilla kernel. The process I followed to get to 10.5.4 is here: http://forum.insanelymac.com/index.php?sho...mp;#entry881737.

Link to comment
Share on other sites
ganzhimself
ganzhimself
Posted
Posted

The first attempt took a dump all over itself after just trying to do it through software update... Well, I reinstalled, and restored from my Time Machine Backup... Tried again, this time using the Combo Update (10.5.2 -> 10.5.5)... I thought the install was messed up, because it never seemed to boot, so I redid the install again. I happened to bump my usb mouse and this time it came back, but no onboard mouse and keyboard... So, I have no idea. Flushed the install again and I'm back at 10.5.2 awaiting some guidance. Probably going to at least upgrade to the Kalyway 10.5.3 combo update, maybe 10.5.4 if I can find it... Ugh. Oh well, it's not like this doesn't work the way it is for now, and I'm sick of reinstalling. If anyone has any advice, that would be awesome.

Link to comment
Share on other sites
bl003r
bl003r
Posted
Posted
I came from 10.5.4. And yes, its a vanilla kernel. The process I followed to get to 10.5.4 is here: http://forum.insanelymac.com/index.php?sho...mp;#entry881737.

 

Thanks.

 

I can get to 10.5.3 via Kaly's combo update but I still can't use Vanilla Kernel or update past 10.5.3. I've gone nuts searching this forum for methods on getting a Vanilla Kernel to work..... there must be still something I'm missing.....

 

Oh well I'll try one more time with the netkas method then I'll wait for Kaly to do a 10.5.5 update

 

Just a quick question.... Are my update problems caused because I've used the Kaly 10.5.2 DVD for the initial install with sleepkernel 9.2.0 (this is the only kernel that works for me atm)?

Link to comment
Share on other sites
 Share
Go to topic listing
×
×
  • Create New...