sajiddesigner Posted November 1, 2015 Share Posted November 1, 2015 Hello, i have installed Mac OS el capitan on my PC. this is a custom build PC. Hardware specs Intel DH55TC Motherboard Core i 5 3.2 ghz processor . (2nd Gen) 4GB Ram 260 GB HDD Nvida Quadro FX 1700 512 Mb Graphics i need help in installing Bootloader, sound and Ethernet. Currently Each time i start my PC, i need to insert my Bootable Installation USB, boot via USB and then select HFS Partition to boot to installed MAC os el captain but i dont have any sound and ethernet. Please tell me how can i fix this. I tried installing Clover Legacy, Clover Root and Clover EFI files but no luck. I also tried installing kext from Mutlibeast 7.5Previously i was using Mavericks and [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url]/[url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] and it was working fine on same machine. Waiting for response.. Thank you Link to comment Share on other sites More sharing options...
Hangten Posted November 1, 2015 Share Posted November 1, 2015 It appears that you haven't moved any of your kext's or config.plist over to your install. Chameleon uses the Extra folder in the root and Clover use the hidden EFI( you have to mount this) When you install your boot loader it doesn't move anything over. Also your aware that El Capitan has SIP and this must be disabled for you to add any kext. Its learning curve, keep at it 1 Link to comment Share on other sites More sharing options...
spakk Posted November 1, 2015 Share Posted November 1, 2015 1) "onboard audio: Realtek ALC888 codec" ----> here on insanelymac.com , go to the side of Meroni or Toleda, there you will find a patched AppleHDA.kext for ALC888 to your OS X version 2) On-board LAN: "One Gigabit Ethernet port controlled by the chipset using an Intel 82578DC to make the physical layer interface" ----> for your LAN card, use the AppleIntelE1000e.kext look here is your Hardware Specification: Main SpecificationsIntel DH55TC motherboard main features are:Socket: 1156.Chipset: Intel H55 Express.Super I/O: Winbond W83627HGClock generator: ICS RS4180ALParallel IDE: None.Serial IDE: Six SATA-300 ports controlled by the chipset.USB: 12 USB 2.0 ports (six soldered on the motherboard and six available through three headers on the motherboard).FireWire (IEEE 1394): None.On-board audio: Produced by the chipset together with a Realtek ALC888 codec (eight channels, 24-bit resolution, up to 192 kHz sampling rate for the outputs, up to 96 kHz sampling rate for the inputs, 90 dB signal-to-noise ratio for the inputs and 97 dB signal-to-noise ratio for the outputs).On-board LAN: One Gigabit Ethernet port controlled by the chipset using an Intel 82578DC to make the physical layer interface.Buzzer: Yes.Power supply required: ATX12V.Slots: One PCI Express 2.0 x16 slot, two PCI Express x1 slots and one standard PCI slot.Memory: Four DDR3-DIMM sockets (up to 16 GB up to DDR3-1333/PC3-10600).Fan connectors: CPU, Front and rear, all four-pin (PWM control).Number of CDs/DVDs provided: One.Programs included: Motherboard drivers and utilities.Extra features: None.More Information: http://www.intel.com 1 Link to comment Share on other sites More sharing options...
sajiddesigner Posted November 2, 2015 Author Share Posted November 2, 2015 It appears that you haven't moved any of your kext's or config.plist over to your install. Chameleon uses the Extra folder in the root and Clover use the hidden EFI( you have to mount this) When you install your boot loader it doesn't move anything over. Also your aware that El Capitan has SIP and this must be disabled for you to add any kext. Its learning curve, keep at it can you please guide me how can i do this. So far i have performed following 1- Installed Clover EFI Packages 2- Opened Clover Configurator and a EFI HD Partion is visible at screen. 3- Saved Clover Configurator file "config.plist" ast desktop and then copied and pasted to EFI/Clover/ directory [replaced/Removed with previously fie]. 4- Restarted my PC to test. On Bootscreen now i can see 3 options 1- Boot from EFI Partiion 2- Boot Mac Os from MacElcapitan (MacElcapitan is my Installation Partition name) 3- Boot from receovery partition. If i select #2 then Apple logo black Screen is visible when loader reaches at middle then system restarted. if I select #1 then it shows Clover Boot screen again after 3- 5 seconds. Please help. 1) "onboard audio: Realtek ALC888 codec" ----> here on insanelymac.com , go to the side of Meroni or Toleda, there you will find a patched AppleHDA.kext for ALC888 to your OS X version 2) On-board LAN: "One Gigabit Ethernet port controlled by the chipset using an Intel 82578DC to make the physical layer interface" ----> for your LAN card, use the AppleIntelE1000e.kext look here is your Hardware Specification: Main Specifications Intel DH55TC motherboard main features are: Socket: 1156. Chipset: Intel H55 Express. Super I/O: Winbond W83627HG Clock generator: ICS RS4180AL Parallel IDE: None. Serial IDE: Six SATA-300 ports controlled by the chipset. USB: 12 USB 2.0 ports (six soldered on the motherboard and six available through three headers on the motherboard). FireWire (IEEE 1394): None. On-board audio: Produced by the chipset together with a Realtek ALC888 codec (eight channels, 24-bit resolution, up to 192 kHz sampling rate for the outputs, up to 96 kHz sampling rate for the inputs, 90 dB signal-to-noise ratio for the inputs and 97 dB signal-to-noise ratio for the outputs). On-board LAN: One Gigabit Ethernet port controlled by the chipset using an Intel 82578DC to make the physical layer interface. Buzzer: Yes. Power supply required: ATX12V. Slots: One PCI Express 2.0 x16 slot, two PCI Express x1 slots and one standard PCI slot. Memory: Four DDR3-DIMM sockets (up to 16 GB up to DDR3-1333/PC3-10600). Fan connectors: CPU, Front and rear, all four-pin (PWM control). Number of CDs/DVDs provided: One. Programs included: Motherboard drivers and utilities. Extra features: None. More Information: http://www.intel.com Thank you for your help, I will try this once Bootloader issues is fixed.\ Link to comment Share on other sites More sharing options...
Hangten Posted November 2, 2015 Share Posted November 2, 2015 The above pic is just as an example and as you can see depending on the version of OS X you have to put the appropriate kext in that folder You have the kext you need? Can you list them? Also if you could install TextWrangler.app (search google) so we can edit your .plist easily. See if you can find this line or similar in your config.plist <key>Boot</key> <dict> <key>Arguments</key> <string>npci=0x2000 kext-dev-mode=1 rootless=0</string> <dict> Link to comment Share on other sites More sharing options...
sajiddesigner Posted November 2, 2015 Author Share Posted November 2, 2015 The above pic is just as an example and as you can see depending on the version of OS X you have to put the appropriate kext in that folder You have the kext you need? Can you list them? Also if you could install TextWrangler.app (search google) so we can edit your .plist easily. See if you can find this line or similar in your config.plist <key>Boot</key> <dict> <key>Arguments</key> <string>npci=0x2000 kext-dev-mode=1 rootless=0</string> <dict> Hello Yes i do have kext and I am copy/pasting kext in appropriate locations. will let you know after copy/pasting I checked config.plist, i have found <key>Boot</key> Only and <dict> <key>Arguments </key> node is missing. Also please tell me how can i fix boot issue, each time i restart PC, i need to boot via USB and then select my Installation partition to go into Mac. Thank you Sajid i have placed kexts in efi/clover/kexts/10.11 directory and restared PC but it did not worked. Please confirm do i need to rebuilt kext cache that we used to do in [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url]. If yes then please tell me how can i do that. Link to comment Share on other sites More sharing options...
Hangten Posted November 3, 2015 Share Posted November 3, 2015 1. Install Clover 2. move the config.plist, kext, driver64UEFI folder with content, and moved your ACPI folder with a patched DSDT and or SSDT 3. config.plist has the edits to boot your system correctly The following is also needed to boot your El Capitan and allow the kext to load (newer versions of clover will load this my default but not the older ones) <key>RtVariables</key> <dict> <key>CsrActiveConfig</key> <string>0x67</string> <key>BooterConfig</key> <string>0x28</string> Can you attach your config list from your installer You must also understand that sometime the installer will use a kext that will take the place of a patched DSDT so thats why Im saying to list them, and you can check out some tools here in the download section at insanelymac. Just a reminder http://www.insanelymac.com/forum/topic/275941-very-important-please-read-about-tonymacx86-and-iatkos-m-y/ Link to comment Share on other sites More sharing options...
ovidoi Posted November 4, 2015 Share Posted November 4, 2015 Hi, my MB is DH55TC, look my install "http://wiki.osx86project.org/wiki/index.php/HCL_10.11_Seeds#Intel",work no issue, with last bios. 1 Link to comment Share on other sites More sharing options...
sajiddesigner Posted November 8, 2015 Author Share Posted November 8, 2015 1. Install Clover 2. move the config.plist, kext, driver64UEFI folder with content, and moved your ACPI folder with a patched DSDT and or SSDT 3. config.plist has the edits to boot your system correctly The following is also needed to boot your El Capitan and allow the kext to load (newer versions of clover will load this my default but not the older ones) <key>RtVariables</key> <dict> <key>CsrActiveConfig</key> <string>0x67</string> <key>BooterConfig</key> <string>0x28</string> Can you attach your config list from your installer You must also understand that sometime the installer will use a kext that will take the place of a patched DSDT so thats why Im saying to list them, and you can check out some tools here in the download section at insanelymac. Just a reminder http://www.insanelymac.com/forum/topic/275941-very-important-please-read-about-tonymacx86-and-iatkos-m-y/ Hello Please see my config.plist contents below <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>ACPI</key> <dict> <key>DSDT</key> <dict> <key>Debug</key> <false/> <key>DropOEM_DSM</key> <false/> <key>ReuseFFFF</key> <false/> </dict> <key>SSDT</key> <dict> <key>DropOem</key> <false/> <key>Generate</key> <dict> <key>CStates</key> <false/> <key>PStates</key> <false/> </dict> </dict> </dict> <key>Boot</key> <dict> <key>Debug</key> <false/> <key>Secure</key> <false/> <key>Timeout</key> <integer>5</integer> <key>XMPDetection</key> <string>Yes</string> </dict> <key>Devices</key> <dict> <key>USB</key> <dict> <key>FixOwnership</key> <true/> <key>Inject</key> <true/> </dict> </dict> <key>GUI</key> <dict> <key>Mouse</key> <dict> <key>DoubleClick</key> <integer>500</integer> <key>Enabled</key> <false/> <key>Mirror</key> <false/> <key>Speed</key> <integer>8</integer> </dict> <key>Scan</key> <true/> </dict> <key>Graphics</key> <dict> <key>Inject</key> <dict> <key>ATI</key> <false/> <key>Intel</key> <false/> <key>NVidia</key> <true/> </dict> <key>NvidiaSingle</key> <false/> </dict> <key>KernelAndKextPatches</key> <dict> <key>AppleRTC</key> <true/> <key>AsusAICPUPM</key> <false/> <key>Debug</key> <false/> <key>KernelCpu</key> <false/> <key>KernelHaswellE</key> <false/> <key>KernelLapic</key> <false/> <key>KernelPm</key> <false/> </dict> <key>SMBIOS</key> <dict> <key>BiosReleaseDate</key> <string>10/20/11</string> <key>BiosVendor</key> <string>Apple Inc.</string> <key>BiosVersion</key> <string>MM51.88Z.0077.B0F.1110201309</string> <key>Board-ID</key> <string>Mac-8ED6AF5B48C039E1</string> <key>BoardManufacturer</key> <string>Apple Inc.</string> <key>BoardType</key> <integer>10</integer> <key>ChassisAssetTag</key> <string>Mini-Aluminum</string> <key>ChassisManufacturer</key> <string>Apple Inc.</string> <key>ChassisType</key> <string>16</string> <key>Family</key> <string>Mac mini</string> <key>Manufacturer</key> <string>Apple Inc.</string> <key>Mobile</key> <false/> <key>ProductName</key> <string>Macmini5,1</string> <key>SerialNumber</key> <string>C02F3630DJD0</string> <key>Trust</key> <false/> <key>Version</key> <string>1.0</string> </dict> </dict> </plist> I have working Sound, Ethernet and USB ports. But issue is with Bootloader Every time when i start my computer, i need to insert my USB stick and then boot from USB and at next screen i need to select Hard Drive Partition in which i have Mac OS installed. Thank you Sajid Link to comment Share on other sites More sharing options...
sajiddesigner Posted March 14, 2016 Author Share Posted March 14, 2016 Hi, my MB is DH55TC, look my install "http://wiki.osx86project.org/wiki/index.php/HCL_10.11_Seeds#Intel",work no issue, with last bios. Hello Ovidoi Please confirm me following things. 1- are you using EFI bootloader or Legacy bootloader 2- I am trying to install xCode 7.2 but system restarts again and again. read detailed issue at http://www.insanelymac.com/forum/topic/311311-successful-el-capitan-install-crashes-again-and-again/?do=findComment&comment=2222557 3- Are you still using this PC specification or not, If yes then which OS version you are using Waiting for your reply Thank you Sajid Link to comment Share on other sites More sharing options...
ovidoi Posted March 14, 2016 Share Posted March 14, 2016 Hi. i use this pc configuration and use El Capitan 10.11.4 beta 4 with clover efi bootloader and work very good. 1 Link to comment Share on other sites More sharing options...
sajiddesigner Posted March 14, 2016 Author Share Posted March 14, 2016 Hi. i use this pc configuration and use El Capitan 10.11.4 beta 4 with clover efi bootloader and work very good. Hello Ovidoi I am also trying to install El Capitan on same machine since last 3-4 months but i am not getting success in this My Specs are Intel Dh55Tc board Intel Core i5 3.2 Ghz Processor 8 GB Ram 250 GB Sata HDD Nvdia Quadro FX 1700 512 Mb Issues i am facing 1- Unable to boot. Each time i need to boot to Mac OS, i have to insert Pen Drive and boot via USB and then select HFS partition to boot into Mac Os 2- This issue aroused since last 2 week. System Crashes any time without any error/kernal panic. Checked -v -x bootflags also. 3- Unable to install any new app since last 2 weeks. each time i try to install any app, system craches during verify process. please help. and let me know how can i fix this, I am using Clover Bootloader 3270 with elcaitan 10.11.1 waiting for reply thanks Link to comment Share on other sites More sharing options...
xenophon Posted April 16, 2016 Share Posted April 16, 2016 Try enabling the AsusAICPUPM kernel patch. Also, regarding your booting troubles: for my DH55PJ, it is necessary to install Clover with the following option selected: Bootloader/boo0af in MBR (along with the ESP selection). HTH 1 Link to comment Share on other sites More sharing options...
Recommended Posts