Jump to content
mitch101

HP Pavilion dv6-3136tx boot0: error after fresh install

16 posts in this topic

Recommended Posts

So continues the problems. I installed OS X today and when I try boot from my HDD it gives me boot0: error. I tried to dual boot it via separate partitions. I can load from the Mac partition via Clover on USB, but it hangs here:

http://i.imgur.com/fuXFDfZ.jpg

By the way, I can also boot into Windows fine from Clover.

Share this post


Link to post
Share on other sites
Advertisement

hello

 

boot0 error

 

http://www.insanelymac.com/forum/topic/278198-boot0error-easiest-way-to-fix-it/

 

try same method for clover...

 

about the bluetoot .. u have video problems.. is u video card u stop the boot

 

good hack

Alright, I'd rather not use the Ubuntu option because my Internet is incredibly slow. As for my video card, it's a ATI Radeon 5650

I suppose I could try fixing the graphics card first, then boot into OS X via my Cloverdrive, and install Chameleon. I found a kext fix but I don't know how to install it.

Share this post


Link to post
Share on other sites

hello

 

the kext are in system/library/extensions

 

for u card no kext fix

 

what u have is bad set in boot loader

 

see the commands for clover

 

try to use eulemur framebuffer

 

and inject edid

 

in clover

 

read about clover

 

good hack

Share this post


Link to post
Share on other sites

hello

 

the kext are in system/library/extensions

 

for u card no kext fix

 

what u have is bad set in boot loader

 

see the commands for clover

 

try to use eulemur framebuffer

 

and inject edid

 

in clover

 

read about clover

 

good hack

Any tutorials for that? Sorry :)

Also the fix is here: http://www.insanelymac.com/forum/topic/262286-ati-radeon-hd-5650-on-lion-107-with-ciqe/

Someone else said I need to patch the appleintelspupowermanagement. I believe something about that showed up during failed boot.

Share this post


Link to post
Share on other sites
Any chance of a more noob friendly tutorial? I reinstalled today with the inbuilt ATI drivers and some things I forgot, still didn't work. I tried a mixture of these flags: -v, -x, and cpus=1. The only other OS I have installed is Windows. Thanks.

Share this post


Link to post
Share on other sites

New: That's impossible to do. I can't even get to the login screen. Any help please? kBluetoothHCIEventHardwareError is the problem.

Share this post


Link to post
Share on other sites

hello

 

lemme give u a advice u follow if u want...

 

mac os x is for mac and developed exclusively for mac

 

hack mac os x is 99% of reading, googling , persistency and 1% of luck u hardware be compatible..

 

this is not windows.. windows install in a toaster.. only need the toaster have a dvd drive..

 

if u don't want to read and hope the things work .. u stay in windows or buy a mac and all u problems are solved.

 

good hack

Share this post


Link to post
Share on other sites

hello

 

lemme give u a advice u follow if u want...

 

mac os x is for mac and developed exclusively for mac

 

hack mac os x is 99% of reading, googling , persistency and 1% of luck u hardware be compatible..

 

this is not windows.. windows install in a toaster.. only need the toaster have a dvd drive..

 

if u don't want to read and hope the things work .. u stay in windows or buy a mac and all u problems are solved.

 

good hack

I did read all of it. I'm just asking if I can get help on it. I don't have a Mac, and I'm not going to buy one for $1500 and not like it, hence installing OSX86. So if you aren't going to help, then that's fine.

Share this post


Link to post
Share on other sites

hello

 

man if u only want get login screen.. remove ati5000controller

 

boot

 

-f GraphicsEnabler=No

 

no acceleration.. but u can boot

 

good hack 

Share this post


Link to post
Share on other sites

hello

 

man if u only want get login screen.. remove ati5000controller

 

boot

 

-f GraphicsEnabler=No

 

no acceleration.. but u can boot

 

good hack

 

Alright, thanks, will try tomorrow. I should be able to modify the Clover config to do that. I also found that Clover has a LAPIC patch which you insert into the config which is tailored for HP notebooks. Thanks :D Xcode Funtime here I come ;)

Share this post


Link to post
Share on other sites

Sorry, that didn't work. Still the same error.

I also spotted something in the Graphics Injector menu. It lists my card, but with no EDID. Would putting the EDID in be the way to go?

Share this post


Link to post
Share on other sites

May as well post the ENTIRE error. Here it is:

[AppleBluetoothHCIControllerUSBTransport][configurePM] ERROR waited 30 seconds and still did not get the commandWakeup() notification this = 0xffffff8010348000

kBluetoothHCIEventHardwareError occurred status = 0x0037 (kBluetoothHCIErrorSecureSimplePairingNotSupportedByHost or kBluetoothHCIErrorMax) mNumberOfCommandsAllowedByHardware 1

[iOBluetoothHCIController::setConfigState] calling registerService

And then it just hangs there.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By TimNeumann
      MB: Asus X99 A-II
      RAM: G.Skill Ripjaws V F4-3200C16D-32GVK (3200MHz, 4x 16GB DIMMs, so Total 64GB) in quad-channel configuration.
      CPU: i7 6800k @4.0Ghz
      GPUs: GTX 1080 Ti and GTX 1060 3GB
      (each one a monitor, because I can't get DVI to run parallel with DP on the 1080Ti, and my second monitor only has DVI/VGA)
      OS: High Sierra 10.13.2 (17C88) / Clover revision: 4392
       
      Hello everybody,
      I occasionally have system crashes and suspect that it is related to RAM. However, this RAM is completely new, and a run with MemTest86+ from the USB stick showed no errors. However, if I use Memtest on MacOS, I get a bunch of error messages, but sometimes none (I restart the computer between tests).  
      As I just discovered, my RAM is not on the recommended vendor list of my motherboard, nor is it on the manufacturer side of the RAM. I have read several times that the RAM may not have been tested by the manufacturer on this platform. Not a single X99 motherboard is listed for this RAM.
      So I also suspect that my RAM is not compatible.
      But if that were the case, how could it sometimes work completely error-free?
       
      During RAM tests in summer 2017 (a slightly different setup, 4x8GB but still G.Skill Ripjaws V) I had no errors at Memtest under MacOS, if I remember correctly. At that time it ran under Sierra 10.12.6. AptioMemoryFix.efi could also cause problems.
      I am appreciative for any help!
       
      Here is an excerpt from a faulty test.
      It is noticeable that it is always the same address during the test, but a different one after each test.
      Memtest version 4.22 (64-bit) Copyright (C) 2004 Charles Cazabon Copyright (C) 2004-2008 Tony Scaminaci (Macintosh port) Licensed under the GNU General Public License version 2 only Mac OS X 10.13.2 (17C88) running in multiuser mode Memory Page Size: 4096 System has 12 Intel core(s) with SSE Requested memory: 57232MB (60012990464 bytes) Available memory: 57232MB (60012990464 bytes) Allocated memory: 57232MB (60012990464 bytes) at local address 0x00000001033e1000 Attempting memory lock... locked successfully Partitioning memory into 2 comparison buffers... Buffer A: 28616MB (30006495232 bytes) starts at local address 0x00000001033e1000 Buffer B: 28616MB (30006495232 bytes) starts at local address 0x00000007ffc4d800 Running 1 test sequence... (CTRL-C to quit) Test sequence 1 of 1: Running tests on full 57232MB region... Stuck Address : ok Linear PRN : testing 7 of 16 FAILURE! Data mismatch at local address 0x0000000e88133d30 Expected Data: 0xc4c340079ac9a645, Actual Data: 0xc4c3400788468846 Running comparison tests using 28616MB buffers... Random Value : ok Compare XOR : ok Compare SUB : ok Compare MUL : ok Compare DIV : ok Compare OR : ok Compare AND : ok Sequential Increment: ok Solid Bits : ok Block Sequential : testing 80 of 256 FAILURE! Data mismatch at local BUFA address 0x000000078b8c7530, BUFB address 0x0000000e88133d30 BUFA Data: 0x4f4f4f4f4f4f4f4f, BUFB Data: 0x4f4f4f4f88468846 Checkerboard : testing 3 of 64 FAILURE! Data mismatch at local BUFA address 0x000000078b8c7530, BUFB address 0x0000000e88133d30 BUFA Data: 0x5555555555555555, BUFB Data: 0x5555555588468846 Bit Spread : testing 1 of 128 FAILURE! Data mismatch at local BUFA address 0x000000078b8c7530, BUFB address 0x0000000e88133d30 BUFA Data: 0x0000000000000005, BUFB Data: 0x0000000088468846 Bit Flip : testing 74 of 512 FAILURE! Data mismatch at local BUFA address 0x000000078b8c7530, BUFB address 0x0000000e88133d30 BUFA Data: 0x0000000000000200, BUFB Data: 0x0000000088468846 Walking Ones : testing 40 of 128 Clover Files attached
      config.plist
      drivers64UEFI.zip
      kexts.zip
      ACPI.zip
    • By iammask
      My laptop is Hp ab522tx(https://support.hp.com/in-en/document/c04863397)
      Product number T0Z73PA Product name HP Pavilion Notebook - 15-ab522tx Microprocessor Intel® Core™ i5-6200U with Intel® HD Graphics 520 (2.3 GHz, 3 MB cache, 2 cores) Memory, standard 8 GB DDR3L-1600 SDRAM (1 x 8 GB) Video Graphics NVIDIA GeForce 940M (4 GB DDR3L dedicated) I made bootable USB of high sierra. While installing it in verbose mode, I get a blank black screen. Mostly its graphics problem with the kext.
      please help guys.
       
    • By bodich
      Hello. I am trying to install 10.13.4 to Samsung 850 Evo 500 GB. I have already well working on same drive 250 GB 10.13.2. Installation starting, I see progress bar, next as usual restarting and coninuing installation. And in one minute (estimated time still did not appear) I have this error...
      It says:
       
      Mac OS could not be installed on your computer
      Unable to complete operation (if I've translated correctly). (com.apple.osinstall, error -3)
       
      I've attached original log file I've saved from there and also attaching it into the spoiler below, screen photo is under the spoiler. Have no idea what it could be, apfs.efi is latest version for 10.13.4, fakesmc is latest, other clover files and config are just the same as on working 10.13.2, clover version latest 4439 (10.13.2 loading well from this efi also). Please help, anybody know what it can be?
       
      Installer Log 04-08-18.txt

    • By brasoel
      hi!!!! I try to install High Sierra 10.13.4 on HP Z400 (Intel Xeon W3520 CPU and Nvidia fx 3800 Graphics) but is unposible for me to boot. I create a vanilla usb and with them i boot normaly to my laptop
      HP DV6 2170 SV Intel I5 Nvidia Gforce Cuda but no to my desktop. The only  way to install hackintosh on HP Z400 for me is with Niresh Zone Installation. When I try  niresh usb on laptop does not work...
      So the vanilla usb is working perfect on laptop but no on desktop and Niresh usb is working perfect on Desktop by no to my laptop.
      My question is; is there someone to help me where is the diference and what is wrong? thank you in advance....
         
    • By Twml
      I have an HP Elitebook 8460P running OSx 10.13.4 High Sierra
       
      I have an odd issue i believe is related to DSDT patch for ACPI Power battery.
      My battery icon works the battery level goes up/down and battery goes black when charging/white when not.
       
      BUT... Always has a lightning bolt in it and says "Power Source: Power Adapter" no matter if its connected or not.
       
       
      How can i get it to recognize my adapter is unplugged?
×