Jump to content

Stuck at whitescreen


alcanfane
 Share

16 posts in this topic

Recommended Posts

I have Asus P8Z77V-LX

EVGA- GTX 570

 

I did install ML and [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url]. After first restart,it ended up with whitescreen and mouse pointer on the left.

 

I tried inject PCIRootUID = 0

 

GraphicsEnabler=No

 

But no luck

 

Link to comment
Share on other sites

  • 2 weeks later...

-v is just for verbose. did you also give npci=0x2000 at boot prompt ?

 

also, at what stage does the "whitescreen" show up ? if you have used -v at the time of booting, you should see a bunch of messages. can you post the last message that you see ? or you can also post a pic of the screen before the white screen appears.

Link to comment
Share on other sites

a video about nothing...a white screen, would be stupid...I'm not at my first hackintosh...

this is not a matter of flags, or may be a questions of boot ..plist

so...I start booting from a kakewalk usb [defined as z68x-ud3] , is same scenario like with uni-bi-st

tried booting with -v, DSDT=No, -f -x... nothing...when it shoud show the welcome screen, it becomes completelly white, and stays like that

 

also, in boot.plist...tried graphics enabler = yes / no,

smc...plist...defined imac12,1/12,2/macpro3,1

still nothing

 

tried also, the power button to put it on sleep, but then it doesn't wake up

 

completelly disarmed... dunno what to do

Link to comment
Share on other sites

Right at the bottom part 7.7:

http://www.insanelym...l=&fromsearch=1

 

If you still get white screen boot with -f -x after removing the mentioned kexts - this will solve your problem.

 

I would appreciate if you could let me know wether the flags are necessary or not

thank you very much

that must be the case... i'm getting into it...i'll report it back here hopefully from a new ML install

  • Like 1
Link to comment
Share on other sites

Right at the bottom part 7.7:

http://www.insanelym...l=&fromsearch=1

 

If you still get white screen boot with -f -x after removing the mentioned kexts - this will solve your problem.

 

I would appreciate if you could let me know wether the flags are necessary or not

well, rockinron_1, I must buy u a drink...

thank u very much bud...as I was suspected, that was the problem...

there wasn'n needed any other flags [use -v anyway]

so, installed, from a kakewalk* usb [used z68x-ud3-b3 predefined mobo]

and after the install, I have reinstalled the ati6000.kext...repaired permissions

I felt necessary to change the dsdt with the one of the tony's specially designed dsdt for my board [z68x-ud5-b3]

--latest chimera

and now, everything seems to be ok**

didn't tested yet the sleep, since my hktosh is still defined as macpro3

I think I will redefine it as imac12,2 and then I'll test the sleep

 

again, thank you...what's your preferred beer?

:))

 

*kakewalk manual has a small error

at Step 4 / 4. Select Install to USB [it should be 'Install Kakewalk']... in fact is somehow logic

the installer, then never ends, but, after some couple of minutes u can exit, it has done its job

 

** audio--ok

ethernet--ok

graphics--ok

 

sleep... testing-----ok

icloud...testing-----ok

usb3... don't have such a device, but I think is fine

 

 

good luck everybody

Link to comment
Share on other sites

 Share

×
×
  • Create New...