Jump to content
teamkiller

[Problem]Core i3 2310M Graphics problems (Intel HD3000 0x0116)

9 posts in this topic

Recommended Posts

Hi guys.

First sorry for my bad english.

 

I Have a Medion Akoya E7220 Laptop

 

I have Problems with the Graphics card of my cpu

 

If I have the HD 3000 Activate, I get a wrong image signal

MacOS, indicates to me that the monitor resolution is 1600x900x32.

The monitor shows only a half picture and the machine slows down.

 

The Dev ID form My HD 3000 is 0x0116 my Cpu is a Sandy Bridge Core i3 2310M (2x 2100MHz with HT)

 

 

The Mainboard Chipset is Intel series 6/C200

 

 

The monitor Edid is:

 

 

 

 

Time: 01:40:29
Date: Mittwoch, 11. Juli 2012
EDID Manager Version: 1.0.0.14
___________________________________________________________________
Block 0 (EDID Base Block), Bytes 0 - 127, 128 BYTES OF EDID CODE:0 1 2 3 4 5 6 7 8 9
000 | 00 FF FF FF FF FF FF 00 06 AF
010 | 9E 12 00 00 00 00 01 13 01 03
020 | 80 26 15 78 0A C4 95 9E 57 53
030 | 92 26 0F 50 54 00 00 00 01 01
040 | 01 01 01 01 01 01 01 01 01 01
050 | 01 01 01 01 F8 2A 40 90 61 84
060 | 0C 30 30 20 36 00 7E D6 10 00
070 | 00 18 00 00 00 0F 00 00 00 00
080 | 00 00 00 00 00 00 00 00 00 20
090 | 00 00 00 FE 00 41 55 4F 0A 20
100 | 20 20 20 20 20 20 20 20 00 00
110 | 00 FE 00 42 31 37 33 52 57 30
120 | 31 20 56 32 20 0A 00 28
(8-9) ID Manufacture Name : AUO
(10-11) ID Product Code : 129E
(12-15) ID Serial Number : 0
(16) Week of Manufacture : 1
(17) Year of Manufacture : 2009(18) EDID Version Number : 1
(19) EDID Revision Number: 3
(20) Video Input Definition : Digital
(21) Maximum Horizontal Image Size: 38 cm
(22) Maximum Vertical Image Size : 21 cm
(23) Display Gamma : 2,20
(24) Power Management and Supported Feature(s):
RGB Color, Non-sRGB, Preferred Timing Mode(25-34) Color Characteristics
Red Chromaticity : Rx = 0,620 Ry = 0,336
Green Chromaticity : Gx = 0,321 Gy = 0,570
Blue Chromaticity : Bx = 0,150 By = 0,056
Default White Point: Wx = 0,313 Wy = 0,329
(35) Established Timings I (Not Used)(36) Established Timings II (Not Used)
(37) Manufacturer's Timings (Not Used)(38-53) Standard Timings (Not Used)
(54-71) Detailed Descriptor #1: Preferred Detailed Timing (1600x900 @ 60Hz)Pixel Clock : 110 MHz
Horizontal Image Size : 382 mm
Vertical Image Size : 214 mm
Refresh Mode : Non-interlaced
Normal Display, No Stereo
Horizontal:
Active Time : 1600 Pixels
Blanking Time : 400 Pixels
Sync Offset : 48 Pixels
Sync Pulse Width: 32 Pixels
Border : 0 Pixels
Frequency : 55 kHzVertical:
Active Time : 900 Lines
Blanking Time : 12 Lines
Sync Offset : 3 Lines
Sync Pulse Width: 6 Lines
Border : 0 Lines
Digital Separate, Horizontal Polarity (-), Vertical Polarity (-)Modeline: "1600x900" 110,000 1600 1648 1680 2000 900 903 909 912 -hsync -vsync
(72-89) Detailed Descriptor #2: Defined by Manufacturer(90-107) Detailed Descriptor #3: ASCII String Data
ASCII String Descriptor: AUO(108-125) Detailed Descriptor #4: ASCII String Data
ASCII String Descriptor: B173RW01 V2(126-127) Extension Flag and Checksum
Extension Block(s) : 0
Checksum Value : 40___________________________________________________________________
System Information Summary:Processor : Intel® Core™ i3-2310M CPU @ 2.10GHz
Operating System : Microsoft Windows 7 Home Premium
OS Version : 6.1.7601
Service Pack : 1.0
Video Controler:Device ID : VideoController1
Name : Intel® HD Graphics Family
Adapter Compatibility: Intel Corporation
Video Processor : Intel® HD Graphics Family
Video RAM : 1,77 GB (1,899,558,912 Bytes)
Availability : Running or Full Power
Driver Version : 8.15.10.2509
PNP Device ID : PCI\VEN_8086&DEV_0116&SUBSYS_20801B0A&REV_09\3&11583659&0&10
Resolution : 1600x900
Max Refresh Rate : 60 Hz
Min Refresh Rate : 60 Hz
Current Refresh Rate : 60 Hz
Current Scan Mode : None-Interlaced
Status : OK

___________________________________________________________________

 

 

 

 

how can i fix the Graphics

 

P.s.

my Kernelflags are:GraphicsEnabler=No -f and i use the Chimera 1.10 bootloader

 

THX Teamkiller

Share this post


Link to post
Share on other sites
Advertisement

If you use a HD 3000 its recommended u run OSX 10.7 Lion or 10.8 Mountain Lion. DO TAKE NOTE THAT A MACBOOKPRO8,1 SMBIOS HAS TO BE USED. If not you'll just get a blank screen, or "SNB framebuffer did not show up unload" in verbose (-v) mode. Do not try the SMBIOS of another Mac that has HD3000 cos those dun work.

 

1. What is your correct resolution?

2. What version of OSX are you using?

Share this post


Link to post
Share on other sites

hi guys,

I'm trying since two weeks now to get my graphics working.

It's a Intel HD 3000 Mobile which comes with my cpu i3-2310M.

After Installation i booted up in single user mode and moved all "AppleIntel*" kext's from /S/L/E to /S/L/E/IntelBack.

Now i was able to boot up. but only in 1024x768. Then i tried to get some kexts.

But no one of the kexts worked for me. Got everytime the same error : Stuck at Apple Boot Logo and Activity indicator freezes. what do i have to do to get this working ? I'm using iATKOS l2 with chimera 1.6 and GraphicsEnabler=Yes.

i'm using the same Laptop a Akoya E7220

it's native resolution is 1600x900.

 

Lectrasxt16

Share this post


Link to post
Share on other sites

Excatly the same problem in my Toshiba P770 ! HM65 chipset / i7 / Hd3000 !

 

Resolution 1600x900 but the screen is very buggy like que LCD kext ! test with smbios 8.1 / 8.2 and / 8.3!

Share this post


Link to post
Share on other sites

Hello Teamkiller,

 

the Same problem here with my internal display.

 

Medion Akoya P7812 Laptop under 10.8.2.

 

The problem : no EDID by default. forcing Edid with Switchres X can give the right display only if i boot in the safe mode with no kext loaded.

 

when booted normally, my internal display show the left half of display with the correct resolution. The colors are very bad.

 

External display ( testes with 3 different monitors) work perfectly.

 

So, it's not a graphic card problem, but screen problem (AUO). if you change the screen, the problem is solved. maybe this AUO category is blacklisted from apple!

 

Maybe we find our hero here in this forum :-)

Share this post


Link to post
Share on other sites

You guys need a duallink dsdt fix for this in your dsdt i will upload my dsdt if you would like to show an example, graphics still are a bit glitchy and you need to remove the appleintelcarpri kext and edit the snb kext i can upload if you would like

 

 

Hello Teamkiller,

 

the Same problem here with my internal display.

 

Medion Akoya P7812 Laptop under 10.8.2.

 

The problem : no EDID by default. forcing Edid with Switchres X can give the right display only if i boot in the safe mode with no kext loaded.

 

when booted normally, my internal display show the left half of display with the correct resolution. The colors are very bad.

 

External display ( testes with 3 different monitors) work perfectly.

 

So, it's not a graphic card problem, but screen problem (AUO). if you change the screen, the problem is solved. maybe this AUO category is blacklisted from apple!

 

Maybe we find our hero here in this forum :-)

Share this post


Link to post
Share on other sites

Hello,

 

Thank you for the replay. I tried different method with some advance. But no perfect solutions.

 

Some changed on my hardware are make:

 

- Screen changed to LG philips Full HD: screen goes black after system starts

 

- CPU changed to I7: screen black, half left screen with the old one.

 

- Trying with DSDT from another laptop with the same configuration : Dell XPS 173x , the display is correct but my battery meter not working with original kexts and with all patched kexts found on the internet.

 

with my riginal DSDT, screen black, but all works with external HDMI display.

i think i need a dsdt modification but no way, i'm unable to get it working.

 

any idea?

 

Thank you.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By jbgillet
      Hi,
       
      I'm having real trouble getting Mojave installed on a clean drives.
       
      I've followed the vanilla guides here, I've even tried Tony with no luck. Most of the time I was unable to even get to the installer, it would either hand at the `End RandomSeed +++++++++++++++++` or I'd get a kernel panic before reaching the installer.
       
      Anyway I finally played around with the config until I was able to get it into loading the installer. I can now get all the way where the loading bar with the apple symbol gets to the end (takes about 20 mins), then the screen goes blank. I've uploaded my config.plist if anyone had any ideas.
      I've disabled iGPU in BIOS.
       
      Hardware:
      Core i7 8700 ASUS Prime Z370-A Radeon Sapphire RX570 8G (tried cable in Display port and HDMI) 32GB Corsair 3000Mhz  Samsung 970 Evo M.2. SSD (blank)  
      I've currently got the following Ktexts:
      AppleALC.kext FakeSMC_ACPISensors.kext FakeSMC_CPUSensors.kext FakeSMC_GPUSensors.kext FakeSMC_LPCSensors.kext FakeSMC.kext IntelMausiEthernet.kext Lilu.kext WhateverGreen.kext  
      I can see this during a -v before it goes blank.
       
       
       
      config.plist

    • By Teerachat
      Hi every body, I am a new user of mac os. I use IMaC late 2017 mac os high sierra 10.13.6(17G65). I want to use Titan V as an external eGPU for molecular dynamic simulation. First I download 
      Webdriver-387.10.10.15.15.108.pkg. And it cannot detect my eGPU (I use sonnet breakaway box 350 watts). My question are : i) what driver NVIDIA is suitable for this mac os version  and it should be compatible with Titan V ii) what procedures should I follow to complete installation and make it working?.
       
      Thank you so much
       
      Teerachat
    • By Shanduur
      So let’s start from beginning. I’m owner of Lenovo Yoga 720-15IKB, with:
      i5-7300HQ Intel HD630 Intel HM175 GTX 1050 2GB (disabled) Intel SSD 660p Dell DW1820A (CN... version, working OOTB) I’ve found some configs to Yoga 720-15, but every is for i7-7700HQ version. I tried using Vesavlad’s config, and some random configs from TonyMacX86, with no luck. I’ve found, that I’m not the only person that tried that, but the second person abandoned their attempt to get it working...

      Here is what I’ve found:
      with Vesavlad’s config I can boot to installer, create APFS partition. In stage 2, after 1st reboot I’m getting this message. disabling Intel TPT does not allow me to get into installer. Nothing, just flashing black screen and back to clover and/or Windows 10 (according to boot settings). creating installer from MacOS 10.9 Mavericks works best for me. After making installer form Mojave, I was stuck on Prohibited sign.  
      What should I do, to make it working? Is there really any huge difference between config for i5 and i7? Why am I unable to boot to installer with Intel TPT disabled?
       
      My BIOS settings:
      Configuration Wireless LAN [Enabled] SATA Controller Mode [AHCI] Graphic Device [Switchable Graphics] Power Beep [Disabled] Intel Virtualization Technology [Enabled] Bios Back Flash [Disabled] Hotkey Mode [Disabled] Always On USB [Enabled] Thunderbolt (TM) Device Boot Support [Enabled] Thermal Control [Performance] Security Intel Platform Trust Technology [Enabled] Intel SGX [Disabled] Secure Boot [Disabled] Boot Boot Mode [UEFI] Fast Boot [Enabled] USB Boot [Enabled] PXE Boot to LAN [Disabled] IPV4 PXE First [Disabled]
    • By Mister3000
      hi guys,
       
      Im hoping some one can help me out of this jam. maybe this is an easy fix but im lost.
       
      I've been running yosemite for years on my asus N53SV but i figured its time to upgrade.. and since i was told mojave its too much trouble im fine with going to High Sierra.
      my issue is this:
       
      I created a usb boot and grabbed a clover folder from a website that claimed everything worked out of the box. i was able to boot in to the setup screen, however my image looks all distorted. im guessing it has something to do with the fact that i replaced the panel on  my laptop from a 720P to a 1080p display. i was able to solve this same issue when i was on yosemite by using a patched DSDT but if i use that same old patch DSDT then i get issues/conflicts like my internal keyboard and trackpad not working.
       
      This are my specs:
      ASUS N53SV
      HD3000 1080p
      i7 2670qm
      512 GB SSD
      8GB Ram
       
      maybe someone can point me in the right direction.. 
       
      Im attaching aa picture in case someone has seen this issue before.
       
      Thanks
       
       

×