post a photo
doesn't work for me on my G41MT-D3 still have errors i can not have instal screen please help
Posted 24 June 2011 - 09:57 PM
Posted 24 June 2011 - 11:20 PM
ok i have this:
try with HackBoot V5
Posted 25 June 2011 - 02:08 AM
Posted 26 June 2011 - 12:21 AM
Posted 26 June 2011 - 12:44 AM
try with arch=i386 -x
no good i got a black screen i'm so sad i take many days to try install snow on it
the problem is GPU
Posted 26 June 2011 - 05:03 AM
i have tried arch=i386 -x same problem at the end have a black screen.. do you think my ram is the problem or not?
what about my bios parameters ?
Posted 26 June 2011 - 07:16 AM
Are you runing oced CPU? If you are, i had a few problems with my PC. Just set a def MUTLY and FSB for your clock (exp: 3200 > 320 * 10 instand od 400*8).
ok i have this:
Uploaded with ImageShack.us
sorry for the crappy quality...
Ok, i need AppleHDA i ALC889A for my bord, MaLd0n past something
Posted 26 June 2011 - 08:43 AM
Posted 26 June 2011 - 08:50 AM
I mean if you set overclock that not use a default multy of your cpu. My setup was 3200 (def 10) but, i used 400 fsb with multy 8 to achive 3200 mhz. After update only 3200 is possible with def multy 10. Any other > KP.
what i don't understand? you think i must specify the fsb for my cpu?
Posted 26 June 2011 - 05:58 PM
Posted 27 June 2011 - 08:43 AM
No patchs seleted when running DSDT Auto Patcher.
Posted 06 July 2011 - 04:15 PM
All of them begin to load from HD and then reboot.
Maybe these screen shots will help.
I start by loading from any HackBoot CD, in this case, v6.2
This is my Video Card: Sentey nVidia G210 1GB DDR3
Screen__1_Video_Card.jpeg 31.89KB 3 downloads
Then, my Mobo: Gigabyte H61M-D2P-B3 Rev 1 Bios F5 with an Intel i3 2100 1155
Screen__2_Bios.jpeg 56.24KB 9 downloads
Bios is set in AHCI mode:
Screen__3_AHCI.jpeg 73.8KB 14 downloads
Screen__4_Chameleon.jpeg 16.08KB 16 downloads
Then I choose Verbose
Screen__5_Verbose.jpeg 49.5KB 20 downloads
at this last line, it goes blank and the system reboots. I cannot pass this point.
In the HD SL installation I copied Extra 12.1 folder I downloadad from this thread and installed Chameleon RC5 just as you described. The system won't load without CD loader (only [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url]).
Any idea what can be causing this? [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] method didn't work either.
Thank you very much in advance,
Posted 06 July 2011 - 09:43 PM
Posted 08 July 2011 - 07:29 AM
I've just built a new configuration with the following specs:
- i7 960es @ 3,2GHz (origin, 133x24)
- 2GB DDR3 1333
- DSDT patched (it says it is) with autopatcher (extracted as you mention in your very good tuto)
- Last Chameleon
- Combo update 10.6.8
Everything is ok but only with the "cpus=1" option, or I get cpu panics on startup (at the end of loading or just a few seconds after beeing logged, or when I open Safari...)
I've tried different options in Chameleon: busratio to 12 (as I saw in another post), 20, 24 (which is for 3,2GHz), NullCPUPowerManagement, but I still get KP.
1- Is there a problem in my DSDT.aml?
2- When "cpus=1" is enabled, are all cores working? (seen as 3,2GHz Intel Core i7, 1 CPU, 4 Cores, but only 1mb L3))
3- Could you solve my problem ??? Thank you
I joint my extra folder and a screen capture
ExtraMacPro51.zip 564.71KB 9 downloads
MacPro51.tiff 560.85KB 9 downloads
Posted 08 July 2011 - 05:16 PM
2- Only one
3- Try MacPro4,1
Posted 08 July 2011 - 06:56 PM
Posted 08 July 2011 - 07:59 PM
2- Only one
3- Try MacPro4,1
The boot was ok with MacPro4,1 Extra, but after a few seconds, I got a KP:
panic(cpu 7 caller 0xffffff80002d0238) : Machine Check thread:0xffffff8005b441c8 at 0xffffff7f8086958a, registers:
CR0: 0x000000008001003b, CR2: 0x0000000100d4b338, CR3: 0x0000000000100000, CR4: 0x0000000000000660
RAX: 0x0000000000000001, RBX: 0xffffff80055fa800, RCX: 0x0000000000000001, RDX: 0xffffff7f8087b4c0
RSP: 0xffffff803586bd60, RBP: 0xffffff803586bda0, RSI: 0xffffff80055fa800, RDI: 0xffffff800567fb80
R8: 0x0000000000000000, R9: 0000000000480000, R10: 0x0000000000080000, R11: 0xffffff80002d6648b
R12: 0xffffff7f8087bc68, R13: 0xffffff800567fa40, R14: 0x0000000000000001, R15: 0xffffff7f80879d18
RFL: 0x0000000000000082, RIP: 0xffffff7f8086958a, CS: 0x0000000000000008, SS: 0x0000000000010
Error code: 0x0000000000000000
Debugger called: <panic>
Backtrace (CPU 7), Frame : Return Address
0xffffff80301ffeb0 : 0xffffff8000204d15
0xffffff80301fffb0 : 0xffffff80002d0238
0xffffff80302000a0 : 0xffffff80002e48ff
0xffffff803586bda0 : 0xffffff7f80861567
0xffffff803586be80 : 0xffffff7f808628a7
0xffffff803586bf20 : 0xffffff800022e409
0xffffff803586bf40 : 0xffffff80002083a4
0xffffff803586bf80 : 0xffffff800027f532
0xffffff803586bfa0 : 0xffffff80002c8527
Kernel Extensions in backtrace (with dependencies):
BSD process name corresponding to current thread: kernel_task
Mac OS version:
Darwin Kernel Version 10.8.0: Tue Jun 7 16:32:41 PDT 2011; root:xnu-1504.15.3-1/RELEASE_X86_64
System model name: MacPro4,1
System uptime in nanoseconds: 77522906657
It was a bit long to write but I hope it is worth it
During these KPs, CPU number is no always the same
So, what do you think of it MaLdOn?
Thank you again!
Edit: the bug is an old nightmare now! I ommitted to mention that I also installed a PCI wifi card that worked well with my old macpro under 10.6.7 (Linksys DWA-547). I noticed that KPs arrived just after the initialization of airport, or when I launched Safari, so I removed it and now everything is OK D:
Do you think there is a solution with that card, or do you have another one to suggest me? (I really need a wifi connection)
Thank you MaLdOn and sorry for the time you spent to help me
Posted 09 July 2011 - 01:27 PM
But I'm unable to get Auto-Patcher to compile the code for my K8NSC-939 (generated using the "Generic" extractor).
[Line 2379 type Error message String must be entirely alphanumeric (_NVRAIDBUS)] [Line 2379 type Error message _HID string must be exactly 7 or 8 characters (_NVRAIDBUS)]
Any info on correcting this is greatly appreciated.
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users