Jump to content

Dell Optiplex GX520


Dellmantt
 Share

282 posts in this topic

Recommended Posts

The GX520 comes with 3 processors

Intel® Pentium® D Processor with Dual Core Technology Up to 820 (2.8GHz,2X1M,800MHz FSB)

Intel® Pentium® 4 Processor with Hyper-Threading Technology Up to 650 (3.4GHz,2M,800MHz FSB)

Intel® Celeron® D Processor Up to 351 (3.2GHz,256K,533MHz FSB)

and 3 case case configurations, mini tower, desktop and SSF (small form factor). The GX620 comes in an additional case an UltraSmallFormFactor. All share the same motherboard chipset and integrated audio, video & wired network (shown in my sig below).

http://www.dell.com/us/en/dfh/desktops/opt...cs=22&s=dfh

8086;Intel Corporation;2770;82945G/GZ/P/PL Memory Controller Hub;Bridge;Host bridge
8086;Intel Corporation;2776;82945G/GZ Integrated Graphics Controller;Display controller;Display controller
8086;Intel Corporation;27cc;N10/ICH 7 Family USB2 EHCI Controller;Serial bus controller;USB Controller
8086;Intel Corporation;27de;82801G (ICH7 Family) AC'97 Audio Controller;Multimedia controller;Multimedia audio controller
8086;Intel Corporation;27df;82801G (ICH7 Family) IDE Controller;Mass storage controller;IDE interface
8086;Intel Corporation;27c0;N10/ICH7 Family SATA IDE Controller;Mass storage controller;IDE interface
8086;Intel Corporation;27da;N10/ICH 7 Family SMBus Controller;Serial bus controller;SMBus
8086;Intel Corporation;27cb;N10/ICH 7 Family USB UHCI Controller #4;Serial bus controller;USB Controller
8086;Intel Corporation;27ca;N10/ICH 7 Family USB UHCI Controller #3;Serial bus controller;USB Controller
8086;Intel Corporation;27c9;N10/ICH 7 Family USB UHCI Controller #2;Serial bus controller;USB Controller
8086;Intel Corporation;27c8;N10/ICH7 Family USB UHCI Controller #1;Serial bus controller;USB Controller
8086;Intel Corporation;27b8;82801GB/GR (ICH7 Family) LPC Interface Bridge;Bridge;ISA bridge
8086;Intel Corporation;2772;82945G/GZ Integrated Graphics Controller;Display controller;VGA compatible controller
8086;Intel Corporation;2771;82945G/GZ/P/PL PCI Express Root Port;Bridge;PCI bridge
8086;Intel Corporation;27d2;N10/ICH 7 Family PCI Express Port 2;Bridge;PCI bridge
14e4;Broadcom Corporation;1677;NetXtreme BCM5751 Gigabit Ethernet PCI Express;Network controller;Ethernet controller
8086;Intel Corporation;27d0;N10/ICH 7 Family PCI Express Port 1;Bridge;PCI bridge
8086;Intel Corporation;244e;82801 PCI Bridge;Bridge;PCI bridge

 

I would suggest that you read right through and then re-read to make sure you understand each step and/or download/print for future reference

 

Please read the EDITS before posting a question.

 

What you need for install

1- Access to a MAC or Hack (Running 10.0-10.6 doesn't matter which)

2- Mac OS X Install DVD

3- 8GB or larger External USB Drive or Flash Drive

4- myHack installer found here http://osx86.sojugarden.com/2010/06/myhack...r-1-1-released/

UPDATE- Updated myHack for the 10.6.4 Legacy Kernel http://blog.nawcom.com/?p=242

5-Carbon Copy Cloner (free) found here http://www.bombich.com/

6-One Kext each for Audio, Lan & Video Note for video with 10.6.3-4 you only need one kext for video but

if you are installing form an earlier DVD or image you will need to upgrade to at least 10.6.3, if not a DSDT

or GFX Strings will be needed (kexts posted below)

7-Common sense & patience.

 

This method differs from the method on the myhack site as I found this simpler. I will call the Mac or Hack used to do this "Donor" the USB drive "Install"

 

INSTALLATION -- Attach USB drive to "Donor" computer. Open Disk Utility and partition the USB drive. Use one partition Mac OS extended journaled and under options pick GUID partition table.

 

Insert Mac OS X Install DVD. DO NOT click on the install Mac OS X when it pops up.

In the Finder Go Menu- Go to folder-type /Volumes/Mac OS X Install DVD/System/Installation/Packages..Open 'OSInstall.mpkg NOT OSInstall.pkg or the upgrade.pkg ..MAKE SURE that the destination chosen is the external drive "Install" Under the custom tab, uncheck printer drivers, languages, fonts etc, if you need any of these, they can be installed later. When the install is finished, close the installer.

 

Note: If you get an installation failed message after install it is safe to ignore it, this is a common but inconsistent error. It happens when the installer can not “bless” the targeted partition and it believes your system will not be bootable.

 

Next (still on 'Donor" computer open the myHack.mpkg. It is most IMPORTANT that you change install location to the USB drive "Install"

Check the following options..com.apple.Boot.plist......Graphics Enabler....Chocolate Kernel......evOverboot.kext......IOATAFamily.kext....

..IONetworkingFamily.kext.....Elliotforcelegacy.kext.......NullCPUPowerManagement.kext--

Close myhack installer when finished.

post-530376-1285875554_thumb.png

 

Copy Carbon Copy Cloner (CCC) and myHack.mpkg all these attachments to the USB disc "Install" They will be needed later.

Chameleon_2.0_RC4.zip

AppleAC97Audio.kext.zip

Updated KextAppleAC97Audio.kext.zip

AppleBCM5751Ethernet.kext.zip

AppleIntelIntegratedFramebuffer.kext.zip EDIT For DSDT for Video see Post #4 below. If you intend to do the dsdt DON"T install frame buffer kext.

Kext_Utility.zip

 

Eject and unplug "Install" from "Donor"

 

TRANSFER TO OPTIPLEX -- Plug in USB "Install" to your Dell Optiplex. Boot dell and enter Bios (tap F2 key while starting) Under Drives/Sata operation choose Combination, save and exit bios now Tap F12 to enter boot options, choose USB device. When you see the Chameleon Boot loader screen tap the space bar and type -v If the boot hangs this will help. Be patient the first boot always take time.

You should get to the OS X setup screen, you will not have sound or ethernet or accelerated graphics yet, will fix that later.

 

TRANSFER from "Install" to Dell Optiplex Hard Drive-- You should now be booted into OS X on the Dell from the USB Drive. Open Disk Utility and partition the Dell Internal Drive. If you want to dual boot with Windows Later have two partitions on Mac os extended and one NTFS (or DOS) or you may want to have a partition for your OS X backup, or three partitions MAC-Windows-Backup. or just one partition. For simplicity now name your os x partition "MAC" Whatever you choose go ahead and do it.

 

When you have finished partitioning open CCC, set source to"Install", destination to "MAC" settings to copy all and erase destination unchecked. Go ahead and clone.

When cloning is finished run myhack again with the same settings, destination "MAC" .. or simpler run the Chameleon installer if you downloaded it earlier again select destination "MAC". Either method will do the same, that is, install the boot loader to the internal drive.

 

Now restart and boot from "MAC"

 

 

 

EDIT For Onboard Network problems. With some routers a "mac address has to be set. Thanks to Weazlmon for this solution

Open a terminal window and type (not sure if you need to sudo -s first):

 

cd /etc

sudo nano rc.local

 

edit the end of the file with:

 

ifconfig en0 ether xx:xx:xx:xx:xx:xx

 

where you replace the xx's with your actual MAC address

 

press ctrl-x, and select y to save it.

 

 

OK Video, Audio & Lan--- Move the kexts & kext utility to desktop, Unzip them all. Drag audio, ethernet & framebuffer kexts onto kext utility icon and it will install them and rebuild caches and permissions automatically. when it is finished reboot and all will be working.

 

 

UPDATE to 10.6.4 -- Don't update via Software Update

If you have 10.6.0-10.6.2 download the combo update here http://support.apple.com/kb/DL1048?viewlocale=en_US

If you have 10.6.3 you can get away with the slightly smaller update here http://support.apple.com/kb/dl1049.

Download the 10.6.4 Legacy Kernel from http://www.insanelymac.com/forum/index.php?showtopic=221599

Run the 10.6.4 update but DON"T RESTART

Run MyHack installer (same settings as above)-DON"T RESTART

Run 10.6.4 Legacy Kernel installer-DON"T RESTART

Re install framebuffer kext with kext utility

Now restart

 

UPDATE to 10.6.5 --Don't update via Software Update

If you have 10.6.0 -10.6.3 Download the 10.6.5 Combo Update from Apple

If you have 10.6.4 you can download the smaller 10.6.5 Update.

Run the update - DON"T RESTART

Download and install 10.5 Legacy Kernel

http://www.insanelymac.com/forum/index.php...t&p=1588262

Now restart -If you have not done the DSDT fix for Video. you will have to reinstall the frame buffer kext.

 

UPDATE to 10.6.6

If you have 10.6.5 Download and install the 10.6.6 update http://support.apple.com/kb/DL1343

If you have 10.6.4 or earlier, Download and install the 10.6.6 combo update .http://support.apple.com/kb/DL1349 If you use the combo update install Legacy Kernel before restart

If you have not done the DSDT fix for Video. you will have to reinstall the frame buffer kext.

10.6 Legacy Kernel available http://blog.nawcom.com/?p=538

UPDATE to 10.6.7

Read the previous updates re Kernel & GMA 950 frame buffer. If you have a DSDT fix for Video & using the Vanilla kernel boot file patch just update via software update. If not here is the new kernel for 10.6.7 http://dl.nawcom.com/legacy_kernel-10.7.0.pkg.zip

 

EDIT _ EDIT You can now run the vanilla kernel

Thank you to scififan68 for this

See here http://osx86.co/f36/new-modify-chameleon-b...l-cpu-to-t6737/

boot.zip

NullCPUPowerManagement.kext.zip

Chameleon.699.zip

See posts 117-124

Change com.apple.boot.plist in extra folder to

<key>Kernel</key>

<string>mach_kernel</string>

If you upgrade "Chameleon" at any time you must replace the "Boot" file again. I suggest you leave the "Legacy Kernel" in place so that you can boot "legacy_kernel" at the boot prompt in case of problems.

 

**** Glad to have any suggestions re errors or omissions. ****

****Any suggestion on how to improve guide welcome ****

 

***** While I am more than happy to help people as far as my limited prowess allows, as my avatar suggests I will not spoon feed anyone that is too lazy to do some research themselves. I also wont assist via PM or email, so please dont ask.(have had previously requests)********

  • Like 2
Link to comment
Share on other sites

Hey, I have the GX620 and the onboard GMA 950 is working perfectly(as well as my nvidia card) with only vanilla kexts , with a minor dsdt patch. It's even immune to updates! (full dsdt with both parts attached) This is just the best method for getting video working, forget that patched kext, because it has annoying artifacts anyways.

EDIT: only works with lcd monitors.

intelgma950gx620dsdt.zip

Link to comment
Share on other sites

Great instructions - however I'm getting a "can't find chocolate_kernel" at boot.

 

Any idea why this would be happening? In my 520's bios, I've set the USB device as the first device in the boot order sequence.

 

Any help would be appreciated!

 

UPDATE:

I simply re-ran the installation on the usb drive and it did not fail - I was able to boot and install!

Link to comment
Share on other sites

  • 2 weeks later...
Hey, I have the GX620 and the onboard GMA 950 is working perfectly(as well as my nvidia card) with only vanilla kexts , with a minor dsdt patch. It's even immune to updates! (full dsdt with both parts attached) This is just the best method for getting video working, forget that patched kext, because it has annoying artifacts anyways.

 

For those who wish to compile their own dsdt, and I would recommend making your own instead of using someone else's, go here http://www.insanelymac.com/forum/index.php?showtopic=223205. This is very easy to use and the patches you need (DTGP & GMA950 Desktop) are included. There is a link to a video tutorial a well. If you have trouble with a compile error (length) or get a blank grey screen, read posts on pages 18-19-20. For grey screen or KP problems- Google "Remove dsdt.aml single user"

 

And you need to replace the  AppleIntelIntegratedFramebuffer.kext from the guide with the original (vanilla) kext.

Link to comment
Share on other sites

The GX520 comes with 3 processors an intel® Pentium® 4 dual core, Intel® Celeron® D & Intel® Pentium® D and 3 case case configurations, tower, desktop and SSF (small form factor). The GX620 comes in an additional case an UltraSmallFormFactor. All share the same motherboard chipset and integrated audio, video & wired network (shown in my sig below).

 

I would suggest that you read right through and then re-read to make sure you understand each step and/or download/print for future reference

 

What you need for install

1- Access to a MAC or Hack (Running 10.0-10.6 doesn't matter which)

2- Mac OS X Install DVD

3- 8GB or larger External USB Drive or Flash Drive

4- myHack installer found here http://osx86.sojugarden.com/2010/06/myhack...r-1-1-released/

5-Carbon Copy Cloner (free) found here http://www.bombich.com/

6-One Kext each for Audio, Lan & Video Note for video with 10.6.3-4 you only need one kext for video but

if you are installing form an earlier DVD or image you will need to upgrade to at least 10.6.3, if not a DSDT

or GFX Strings will be needed (kexts posted below)

7-Common sense & patience.

 

This method differs from the method on the myhack site as I found this simpler. I will call the Mac or Hack used to do this "Donor" the USB drive "Install"

 

INSTALLATION -- Attach USB drive to "Donor" computer. Open Disk Utility and partition the USB drive. Use one partition Mac OS extended journaled and under options pick GUID partition table.

 

Insert Mac OS X Install DVD. DO NOT click on the install Mac OS X when it pops up.

In the Finder Go Menu- Go to folder-type /Volumes/Mac OS X Install DVD/System/Installation/Packages..Open 'OSInstall.mpkg NOT OSInstall.pkg or the upgrade.pkg ..MAKE SURE that the destination chosen is the external drive "Install" Under the custom tab, uncheck printer drivers, languages, fonts etc, if you need any of these, they can be installed later. When the install is finished, close the installer.

 

Note: If you get an installation failed message after install it is safe to ignore it, this is a common but inconsistent error. It happens when the installer can not “bless” the targeted partition and it believes your system will not be bootable.

 

Next (still on 'Donor" computer open the myHack.mpkg. It is most IMPORTANT that you change install location to the USB drive "Install"

Check the following options..com.apple.Boot.plist......Graphics Enabler....Chocolate Kernel......evOverboot.kext......IOATAFamily.kext....

..IONetworkingFamily.kext.....Elliotforcelegacy.kext.......NullCPUPowerManagement.kext--

Close myhack installer when finished.

post-530376-1285875554_thumb.png

 

Copy Carbon Copy Cloner (CCC) and myHack.mpkg all these attachments to the USB disc "Install" They will be needed later.

Chameleon_2.0_RC4.zip

AppleAC97Audio.kext.zip

AppleBCM5751Ethernet.kext.zip

AppleIntelIntegratedFramebuffer.kext.zip

Kext_Utility.zip

 

Eject and unplug "Install" from "Donor"

 

TRANSFER TO OPTIPLEX -- Plug in USB "Install" to your Dell Optiplex. Boot dell and enter Bios (tap F2 key while starting) Under Drives/Sata operation choose Combination, save and exit bios now Tap F12 to enter boot options, choose USB device. When you see the Chameleon Boot loader screen tap the space bar and type -v If the boot hangs this will help. Be patient the first boot always take time.

You should get to the OS X setup screen, you will not have sound or ethernet or accelerated graphics yet, will fix that later.

 

TRANSFER from "Install" to Dell Optiplex Hard Drive-- You should now be booted into OS X on the Dell from the USB Drive. Open Disk Utility and partition the Dell Internal Drive. If you want to dual boot with Windows Later have two partitions on Mac os extended and one NTFS (or DOS) or you may want to have a partition for your OS X backup, or three partitions MAC-Windows-Backup. or just one partition. For simplicity now name your os x partition "MAC" Whatever you choose go ahead and do it.

 

When you have finished partitioning open CCC, set source to"Install", destination to "MAC" settings to copy all and erase destination unchecked. Go ahead and clone.

When cloning is finished run myhack again with the same settings, destination "MAC" .. or simpler run the Chameleon installer if you downloaded it earlier again select destination "MAC". Either method will do the same, that is, install the boot loader to the internal drive.

 

Now restart and boot from "MAC"

 

EDIT For DSDT for Video see Post #4 below. If you intend to do the dsdt DON"T install frame buffer kext.

 

OK Video, Audio & Lan--- Move the kexts & kext utility to desktop, Unzip them all. Drag audio, ethernet & framebuffer kexts onto kext utility icon and it will install them and rebuild caches and permissions automatically. when it is finished reboot and all will be working.

 

 

UPDATE to 10.6.4 -- Don't update via Software Update

If you have 10.6.0-10.6.2 download the combo update here http://support.apple.com/kb/DL1048?viewlocale=en_US

If you have 10.6.3 you can get away with the slightly smaller update here http://support.apple.com/kb/dl1049.

Download the 10.6.4 Legacy Kernel from http://www.insanelymac.com/forum/index.php?showtopic=221599

Run the 10.6.4 update but DON"T RESTART

Run MyHack installer (same settings as above)-DON"T RESTART

Run 10.6.4 Legacy Kernel installer-DON"T RESTART

Re install framebuffer kext with kext utility

Now restart

 

More info on SL on GX520 here http://www.insanelymac.com/forum/index.php?showtopic=191179

 

**** Glad to have any suggestions re errors or omissions. ****

****Any suggestion on how to improve guide welcome ****

 

***** While I am more than happy to help people as far as my limited prowess allows, as my avatar suggests I will not spoon feed anyone that is too lazy to do some research themselves. I also wont (have had previously requests) assist via PM or email, so please dont ask.********

 

Getting gray screen plz help me

Link to comment
Share on other sites

Getting gray screen plz help mGetting gray screen plz help me

I have ALREADY answered this question for you in this post http://www.insanelymac.com/forum/index.php...p;#entry1561993

ONCE AGAIN

IF you put the dsdt.aml in your Extra folder

Boot in single user mode -s

type mount -uw /

hit enter

type rm -rf /extra/dsdt.aml

hit enter

type exit

hit enter

 

IF you put the dsdt.aml in root

Boot in single user mode -s

type mount -uw /

hit enter

type rm -rf /dsdt.aml

hit enter

type exit

hit enter

Link to comment
Share on other sites

I have ALREADY answered this question for you in this post http://www.insanelymac.com/forum/index.php...p;#entry1561993

ONCE AGAIN

IF you put the dsdt.aml in your Extra folder

Boot in single user mode -s

type mount -uw /

hit enter

type rm -rf /extra/dsdt.aml

hit enter

type exit

hit enter

 

IF you put the dsdt.aml in root

Boot in single user mode -s

type mount -uw /

hit enter

type rm -rf /dsdt.aml

hit enter

type exit

hit enter

 

I typed this before i messaged you srry

Link to comment
Share on other sites

Great walk through everything working sort of for the life of me I Can't get this thing on the Internet I've put in it's own ip settings and also used auto dhcp have been trouble shooting this for a while now only thing i can think of is this thing hates my router i cant even ping it. I've tested out 2 other routers that i have on the network but it hates the wrt610n that goes out to Internet I think it has something to do with the mac address by 00:00:00:00:00:00 I don't run any mac filtering on that router maybe it has some built in {censored}. I've tried to spoof my mac address but terminal comes back with bad value no matter what i set it to. Any thoughts?

Link to comment
Share on other sites

Great walk through everything working sort of for the life of me I Can't get this thing on the Internet I've put in it's own ip settings and also used auto dhcp have been trouble shooting this for a while now only thing i can think of is this thing hates my router i cant even ping it. I've tested out 2 other routers that i have on the network but it hates the wrt610n that goes out to Internet I think it has something to do with the mac address by 00:00:00:00:00:00 I don't run any mac filtering on that router maybe it has some built in {censored}. I've tried to spoof my mac address but terminal comes back with bad value no matter what i set it to. Any thoughts?

 

Seen this problem once before, was because of the type of modem/router being used, most work happily with no mac address.

When you say you tried to spoof it. What do you mean? Have you tried

 

sudo ifconfig en0 ether xx:xx:xx:xx:xx:xx Where xx:xx:xx:xx:xx:xx is your mac address, get it from windows or a linux live cd

 

and if you need it to be set at boot search for "setmac".

Link to comment
Share on other sites

Seen this problem once before, was because of the type of modem/router being used, most work happily with no mac address.

When you say you tried to spoof it. What do you mean? Have you tried

 

sudo ifconfig en0 ether xx:xx:xx:xx:xx:xx Where xx:xx:xx:xx:xx:xx is your mac address, get it from windows or a linux live cd

 

and if you need it to be set at boot search for "setmac".

\

 

Wow yeah i was going crazy there for a while was so happy when i first got Mac os on this old Dell that I've kept around for so long cause it's nice and small but damn I now hate that cisco wrt610n going to change that firmware to dd-wrt asap. I changed out with another router setup the ip and dns instant internet woot!! My thanks goes out to the OP and the people that put these mods/hacks/kext installers all that stuff together. Now to find a good post on hp mini 1000. who know maybe after that my i7 yeah right???

Link to comment
Share on other sites

\

 

Wow yeah i was going crazy there for a while was so happy when i first got Mac os on this old Dell that I've kept around for so long cause it's nice and small but damn I now hate that cisco wrt610n going to change that firmware to dd-wrt asap. I changed out with another router setup the ip and dns instant internet woot!! My thanks goes out to the OP and the people that put these mods/hacks/kext installers all that stuff together. Now to find a good post on hp mini 1000. who know maybe after that my i7 yeah right???

Glad it's all sorted

Link to comment
Share on other sites

Quick question By mistake after I finished updating to 10.6.4 I went to do the last part of the guide but for some reason instead of dragging the kext utility to the desktop I installed it, is this a bad thing ? I have know clue what it did but it put like 300 kext in or something. I put the graphic kext in after that before i rebooted seems to be working fine but I'd like to know what the heck that was that I installed?? Thanks

Link to comment
Share on other sites

Quick question By mistake after I finished updating to 10.6.4 I went to do the last part of the guide but for some reason instead of dragging the kext utility to the desktop I installed it, is this a bad thing ? I have know clue what it did but it put like 300 kext in or something. I put the graphic kext in after that before i rebooted seems to be working fine but I'd like to know what the heck that was that I installed?? Thanks

 

Go to system/library --right click on extensions-get info-- mine has 208 items and in extra/extension there a 7 kexts. If you have a lot more and see if any are .bak files, if so don't worry. you can trash all the bak files if you wish. I would leave the frame buffer bak file in case you want to go to vanilla video with dsdt in future.

Link to comment
Share on other sites

Go to system/library --right click on extensions-get info-- mine has 208 items and in extra/extension there a 7 kexts. If you have a lot more and see if any are .bak files, if so don't worry. you can trash all the bak files if you wish. I would leave the frame buffer bak file in case you want to go to vanilla video with dsdt in future.

 

Thanks for that info and a perfect how to guide

Link to comment
Share on other sites

hey Peter Exams and paper over can you help me

 

Could you tell me why or what part of the Ktext for graphics changes the screen resolution and what part causes artifacts I wanted to see if I could maybe combine these and get one with full resolution and no artefacts

 

also is your sata drive in bios set as COMBINATION

Link to comment
Share on other sites

This was a very helpful guide! Thanks Dellmantt

 

A couple of things though:

 

I couldn't create my own dsdt.aml file. When I tried to save it - it just simply wouldn't. No error just didn't write the file. Weird. I used the one scififan68 posted and it worked for me, thanks!

 

I also don't get a mac address and have to set one manually. I'm trying the setmac script but its not working. I'm sure I'll figure it out eventually.

 

Other than that this seems to be a solid working machine! I have not tried sound yet - no speakers.

Link to comment
Share on other sites

hey Peter Exams and paper over can you help me
Irrelevant
Could you tell me why or what part of the Ktext for graphics changes the screen resolution and what part causes artifacts I wanted to see if I could maybe combine these and get one with full resolution and no artefacts
Sorry don't know.

Obviously you have not fixed the grey screen/compiling without an error problem. try re -reading the DSDT Editor thread especially the pdave54 post re bios reset with a different monitor

also is your sata drive in bios set as COMBINATION
Yes combination. Video set to on board & 8MB.
Link to comment
Share on other sites

This was a very helpful guide! Thanks Dellmantt
Your welcome
I couldn't create my own dsdt.aml file. When I tried to save it - it just simply wouldn't. No error just didn't write the file. Weird. I used the one scififan68 posted and it worked for me, thanks!
wonder why it did not save, strange. If his dsdt works, fine, although I still recommend that people compile their own.

 

I also don't get a mac address and have to set one manually. I'm trying the setmac script but its not working. I'm sure I'll figure it out eventually.
I have not used setmac since I had Leopard, so can't help you there. Luckily for me, the router works fine with no mac address.
Other than that this seems to be a solid working machine! I have not tried sound yet - no speakers.
If you have audio input and output in System Preferences, it's working.

 

 

I figured out how to set the MAC address automatically. That setMAC script DOES NOT work. Instead I found this MACADD script from another thread that does the job. I'll post it here if I can figure out how to save others the headache.

 

MACADD.txt

Thanks

Link to comment
Share on other sites

Irrelevant

Sorry don't know.

Obviously you have not fixed the grey screen/compiling without an error problem. try re -reading the DSDT Editor thread especially the pdave54 post re bios reset with a different monitor

Yes combination. Video set to on board & 8MB.

 

 

Thanks so much also are you using the hard drive that came with your dell or an after market if so what one

 

It seems my After Market Western Digital doesn't like OS X

 

Also Just to make sure Im supposed to download the editor from the first post right (Is that the updated one?)

Link to comment
Share on other sites

Thanks so much also are you using the hard drive that came with your dell or an after market if so what one

It seems my After Market Western Digital doesn't like OS X

Yes mine is original, can't see why a particular brand of hard drive would make any difference, unless its faulty. test it with "SMART Utility" and or surface scan using a Linux disk.
Also Just to make sure Im supposed to download the editor from the first post right (Is that the updated one?)
I assume so. Why not ask on that thread?
Link to comment
Share on other sites

After reading your post, I think I'll try and install OSX on my Optiplex gx620 "desktop" pc I have at the house.

 

A few questions first.

 

I already have an iMac 27" quadcore and a Macbook Pro.

 

If I setup OSX on my Dell:

 

1) Would that serve as a good Timemachine backup

2) General backup drive / fileserver

3) iTunes Server

 

Thanks in advance.

 

Yogi....

Link to comment
Share on other sites

After reading your post, I think I'll try and install OSX on my Optiplex gx620 "desktop" pc I have at the house.

 

A few questions first.

 

I already have an iMac 27" quadcore and a Macbook Pro.

 

If I setup OSX on my Dell:

 

1) Would that serve as a good Timemachine backup

2) General backup drive / fileserver

3) iTunes Server

 

Thanks in advance.

 

 

 

YES IT WILL I HAVE ONE

 

But 2 PROBS MOUSE TEARING, ARTEFACTS (LAG) WITH GRAPHICS FIX AND MOUSE WILL HAVE PROBLEMS WITH USB

 

TRY IT THO ILL HELP YOU

 

Yogi....

 

 

After reading your post, I think I'll try and install OSX on my Optiplex gx620 "desktop" pc I have at the house.

 

A few questions first.

 

I already have an iMac 27" quadcore and a Macbook Pro.

 

If I setup OSX on my Dell:

 

1) Would that serve as a good Timemachine backup

2) General backup drive / fileserver

3) iTunes Server

 

Thanks in advance.

 

Yogi....

YES IT WILL I HAVE ONE

 

But 2 PROBS MOUSE TEARING, ARTEFACTS (LAG) WITH GRAPHICS FIX AND MOUSE WILL HAVE PROBLEMS WITH USB

 

TRY IT THO ILL HELP YOU

Link to comment
Share on other sites

 Share

×
×
  • Create New...