Jump to content
5539 posts in this topic

Recommended Posts

On 1/22/2020 at 5:40 PM, AudioGod said:

 

@vyu01773 Yes I Made a mistake and pulled it, here try again. sorry.

like the last message said I've generated info for you so just drop the EFI folder in and let me know how it goes.

 

 

vyu01773.zip

I have the same problem that the USB (mouse/keyboard) stops working. I only use the iGPU. However, once I plug in an old ATI Radeon 4600 card (which does not work in this setup) USB is back. Any ideas what I can check/change?

8 minutes ago, tuk3 said:

I have the same problem that the USB (mouse/keyboard) stops working. I only use the iGPU. However, once I plug in an old ATI Radeon 4600 card (which does not work in this setup) USB is back. Any ideas what I can check/change?


you can try removing -wegnoegpu from the clover boot arguments and see if that helps (without the gpu installed)

11 hours ago, AudioGod said:


you can try removing -wegnoegpu from the clover boot arguments and see if that helps (without the gpu installed)

Thanks AudioGod. I now have the mouse but they behave strange. They are very slow for about 1 minute (moving is slow, typing is very slow). After a minute (of doing nothing) they are up to normal. Any ideas? If not I can live with it.

 

1 hour ago, tuk3 said:

Thanks AudioGod. I now have the mouse but they behave strange. They are very slow for about 1 minute (moving is slow, typing is very slow). After a minute (of doing nothing) they are up to normal. Any ideas? If not I can live with it.

 

What version of the UHD630 EFI are you using?

the one on the front page or one of the variations I was sending to somebody else?

 

Edited by AudioGod
14 minutes ago, AudioGod said:

What version of the UHD630 EFI are you using?

the one on the front page or one of the variations I was sending to somebody else?

 

The one at the front page.

And I have another issue: The system crashes 3 sec. after wake from sleep. I traced it down to AppleAlc.kext. Once I block it wake up works - but sound is gone. Any idea on that?

4 minutes ago, tuk3 said:

The one at the front page.

And I have another issue: The system crashes 3 sec. after wake from sleep. I traced it down to AppleAlc.kext. Once I block it wake up works - but sound is gone. Any idea on that?

Could you put your full spec up on your profile so I can see what your using please bud?

1 minute ago, Cameron Nicholson said:

Doesn't work, its ok, I'll stick with clover

 

It works really well, what’s not working for you bud!

  • Like 1
23 minutes ago, AudioGod said:

Could you put your full spec up on your profile so I can see what your using please bud?

It works really well, what’s not working for you bud!

It just freezes within the first few seconds of boot but not at any particular point 

7 minutes ago, Cameron Nicholson said:

It just freezes within the first few seconds of boot but not at any particular point 

Have you entered your details correctly?

@texem any ideas why?
 

26 minutes ago, tuk3 said:

Gigabyte Z390 Aorus Pro (BIOS F12d) - i5 8400 - 16GB DDR 4 RAM Vengeance - iGPU -  TL-WDN4800 WiFi

 

Give this version a try, don’t worry about the user name on it just put your details in and give i a go

 

vyu01773.zip

 

remember to remove the same boot argument again before you try it bud

 

3 minutes ago, Cameron Nicholson said:

I have entered my MLB and serial numbers 

 

Have you got you MSR unlocked?

if you don’t then you need to make the following changes.

 

PLEASE NOTE - These EFIs are setup to be used with your msr Unlocked so make sure you use the F12d Unlocked Profile but if for any reason you can not unlock MSR then just modify following in the OpenCore config.plist :



249434888_Screenshot2020-01-16at19_26_02.thumb.png.948834bc41d84df577e126ae92c9d773.png

 

 

Edited by AudioGod
2 minutes ago, AudioGod said:

Give this version a try, don’t worry about the user name on it just put your details in and give i a go

 

vyu01773.zip

 

remember to remove the same boot argument again before you try it bud

Have you got you MSR unlocked?

if you don’t then you need to make the following changes.


 

  Hide contents

PLEASE NOTE - These EFIs are setup to be used with your msr Unlocked so make sure you use the F12d Unlocked Profile but if for any reason you can not unlock MSR then just modify following in the OpenCore config.plist :



249434888_Screenshot2020-01-16at19_26_02.thumb.png.948834bc41d84df577e126ae92c9d773.png

 

 

Sorry yes, I did that as well.

20 minutes ago, texem said:

 

BIOS F12d and settings as AG recommends ?

NVRAM/CMOS clear before booting OC first time ?

MSR unlocked ?

UUID entered ?


 

Yes f12d, Yes Bios configured as AG's

I tried cleariNg CMOS, same issue

MSR Locked and Config updated to reflect such,

UUID Entered

7 minutes ago, Cameron Nicholson said:

Yes f12d, Yes Bios configured as AG's

I tried cleariNg CMOS, same issue

MSR Locked and Config updated to reflect such,

UUID Entered

 

must be something wrong else .. sry no idea atm

 

if you prepare a Cat install stick und use your OC EFI for installation on the stick , does it boot?

 

12 minutes ago, texem said:

 

must be something wrong else .. sry no idea atm

 

if you prepare a Cat install stick und use your OC EFI for installation on the stick , does it boot?

 

I'll have a play around in the morning

  • Like 1
1 hour ago, AudioGod said:

Give this version a try, don’t worry about the user name on it just put your details in and give i a go

 

vyu01773.zip

 

remember to remove the same boot argument again before you try it bud

Same problem AudioGod, only screen get blank, motherboard stays on. When wakening the screen, the system crashes.

Had success on your original EFI with disableing AppleATC and using VoodoHDA. That gives back sound. Now I only need to figure out how enable autosleep. So far only the screen gets dark after some time but the CPU stays on.

 

The slow USB is due to high CPU on "displaypolicy" at startup or after coming back from sleep. Any of you pros have any advice how to solve this?

×
×
  • Create New...