Jump to content
49 posts in this topic

Recommended Posts

Hi,

 

Just what to share my photos of my Hackintosh mod. the front panel works also :hysterical:

 

Spec:

PowerMac G5 Case

Intel Q9550 2.81 (Speedstep)

GA-EP45T-Extreme (Intel P45, ICH10R, ALC889a(DSDT patch), Realtek 8111C(Bonjour fix)

4Gb DDR3 1333Mhz

500Gb(system) + 320Gb(Windows)

GeForce 9800GTX+ (EFI String)

Retail OSX 10.6.4(64Bit) + Chameleon 2 RC4

 

To come:

SAS disks, need the controller

Infrared

 

 

Photos: http://www.flickr.com/photos/ilovecode/set...4562487/detail/

 

My Extra folder v1 (SL 10.6.1 - 64/32bit - bonjour fix(only in 32Bit)):

Extra_2.zip

My Extra folder v2 (SL 10.6.2 - 64bit - Bonjour fix, CPU Throttle ):

Extra.zip

post-237525-1244632891_thumb.jpg

Link to comment
https://www.insanelymac.com/forum/topic/170112-powerhack-g5/
Share on other sites

  • 3 weeks later...

some more pic.

 

The back of the case.

It's missing the power plug but put it where its normal will be.

3606323855_c20abddf54.jpg

 

3607131542_298cbeb359.jpg

 

Used an lian li motherboard tray

 

3606294891_3a783628b2.jpg

 

My disksbay

The to front fans is strip the the HD cage to provent redundancy

 

3606309047_29365834dd.jpg

Here you can se the small rubber rings

3606309277_7e405934b5.jpg

  • 1 month later...

which PSU are you using??? and would most standard PSU's fit because i am just about to get a case, and am just clearing up little details...

 

 

I have seen the Antec Phantom 500W on macmaniac's mod... Do you think that would suffice?

 

I plan on using my existing EP45-UD3 sig rig with either my thermaltake 480W PSU, if it were to fit, or a new one!, with either the mobo tray linked in this thread, or the one with the fan hole incorporated!

 

http://www.performance-pcs.com/catalog/ind...oducts_id=21886

 

 

Thanks

 

 

BTW, your mod is nice, and looks simple to do...

which PSU are you using??? and would most standard PSU's fit because i am just about to get a case, and am just clearing up little details...

 

 

I have seen the Antec Phantom 500W on macmaniac's mod... Do you think that would suffice?

 

I plan on using my existing EP45-UD3 sig rig with either my thermaltake 480W PSU, if it were to fit, or a new one!, with either the mobo tray linked in this thread, or the one with the fan hole incorporated!

 

http://www.performance-pcs.com/catalog/ind...oducts_id=21886

 

 

Thanks

 

 

BTW, your mod is nice, and looks simple to do...

 

The psu i use is a "NorthQ - NQ-4775-650-FLEX, 650 Watt" Dimensions:150*86*160mm(W*H*L)

Its a real tight fit so there is no need to tape, screw the psu in place, its held by the top of the case and the plate inside the case

 

Hmm I think the motherboard try you link to might be to width. but don't have proff.

 

but look at my backplate its all most the hole width of the case

i think you are right about the mobo tray being too wide. It appears to be 2.5 to 3 cm wider...

 

Your PSU appears to be almost the same size as my Thermaltake 430NP-A2... but i need a new PSU anyway... Would you be able to roughly measure that empty space near the front of the case? i could end up putting my current one there until i get another one.

 

Thanks a lot!

 

 

Also, how did you get the front panel / headers to work.... Is there a guide here?

i think you are right about the mobo tray being too wide. It appears to be 2.5 to 3 cm wider...

 

Your PSU appears to be almost the same size as my Thermaltake 430NP-A2... but i need a new PSU anyway... Would you be able to roughly measure that empty space near the front of the case? i could end up putting my current one there until i get another one.

 

Thanks a lot!

 

 

Also, how did you get the front panel / headers to work.... Is there a guide here?

 

Hi,

 

I'm not sure what space we a talking about ?

Is it this ?

post-237525-1250327381_thumb.jpg

 

Also the tray to get it to fit you have to cut this off.

post-237525-1250327421_thumb.jpg

Hi.

Nice work. I am, myself, looking to do something very similar. One question - did you have to modify the Lian-Li motherboard tray at all or did you use it as you bought it?

 

Thanks

 

Read :)

 

http://www.insanelymac.com/forum/index.php...t&p=1226607

 

I made the Alu backplate my self out of 0.8mm Alu

×
×
  • Create New...