1879 replies to this topic

[karim76]

xboxtreme, on May 16 2010, 11:39 PM, said:

I followed those steps and seems to work.
I have 1920x1080 resolution working
Now when you turn the pc shows me the following.

I have the same problem as you

[zaaherux]

Did you get full qe and ci + resolution? if so, just ignore the stupid warning untill we figure out how to silence it.

[xboxtreme]

plan3r, on May 17 2010, 02:44 PM, said:

Did you get full qe and ci + resolution? if so, just ignore the stupid warning untill we figure out how to silence it.

The resolution is correct, I think also the acceleration.
As I can see if that works qe + ci?

[zaaherux]

xboxtreme, on May 17 2010, 03:29 PM, said:

The resolution is correct, I think also the acceleration.
As I can see if that works qe + ci?

Best way to check for QE+CI is to simply drag'n'drop a widget on your dashboard. If you can see ripple (waves) effect - it's on!

[karim76]

resolution is correct ...

QE + CI is OK

but



be ?

Connector  for Monitor:
State: No monitor  connected

[danzakk]

karim76, on May 17 2010, 05:04 PM, said:

resolution is correct ...

QE + CI is OK

but

I have a similar problem.
And the driver card only works in 32 bit mode

[ZPK]

thx all works in 64bit mode with qe/cl 7280

[karim76]

ZPK, on May 18 2010, 06:27 PM, said:

thx all works in 64bit mode with qe/cl 7280

how?

without...

[ZPK]

yes i have warning but all work

http://rapidshare.co...052926.mov.html

[karim76]

ZPK, on May 19 2010, 02:31 AM, said:

yes i have warning but all work

http://rapidshare.co...052926.mov.html

excuse  me I did not understand.

my board works  perfectly. The only problem is the  message.

Thank you for your example.

[danzakk]

karim76, on May 19 2010, 11:13 AM, said:

excuse  me I did not understand.

my board works  perfectly. The only problem is the  message.

Thank you for your example.

It only works in 32 bits
+ In the center of the screen blinking videocard icon, which discourages work. And the fan on the video card works in active mode.

[hugorus]

plan3r, on May 16 2010, 04:57 PM, said:

If you device id is 7288 downlod this pack
ati_x195...8_10.6.3.zip
and put:
EVOenabler-x19X0.kext,
JaminMc-x19x0-inject-cont.kext and
JaminMc-x19x0.kext in /Extra/Extensions/

and ATIRadeonX1000.kext in
/Sytem/Library/Extensions/ overwriting original there.

Tried to follow this guide. As result it gives me the similar picture like this
http://img444.images...8/img0052ar.jpg
Not my picture though. I can see my cursor and i can move it, seems like OS booted.

If I remove ATIRadeonX1000.kext everything looks clear, video card has been detected properly and resolution changing works well but no qe/ci.

After installing ATIRadeonX1000.kext the problem comes back. Permissions are fine.

Had no problems at all on 10.5.8 and 10.6.2 but I need 10.6.3

Any suggestions for me?

Thanks

[zaaherux]

hugorus, on May 26 2010, 12:58 AM, said:

Tried to follow this guide. As result it gives me the similar picture like this
http://img444.images...8/img0052ar.jpg
Not my picture though. I can see my cursor and i can move it, seems like OS booted.

If I remove ATIRadeonX1000.kext everything looks clear, video card has been detected properly and resolution changing works well but no qe/ci.

After installing ATIRadeonX1000.kext the problem comes back. Permissions are fine.

Had no problems at all on 10.5.8 and 10.6.2 but I need 10.6.3

Any suggestions for me?

Thanks

Yeah, are you sure you did not delete any other ati related kexts? If so, restore them from original 10.6.3 install disk.

[Deeiivid]

Hello, im new.

I have this card. I installed 10.6 and the kext for the drivers. All ok at this point. But I updated the OSX to 10.6.3 and the 3D acceleration desapear. Then I reinstall the kext of 1950 and now my Snow leopard only shows a blue screen (no desktop) without mouse.
Any solution? thx 2 all.

[allpro]

Bronya, on Aug 4 2007, 11:58 AM, said:

P.S.
Attention! I end driver for x1950 pro!
Situation heavy! Job is finished !
Good-bye!
----------------------------------------------

Hi all Children!
At last I have made AtiradeonX1000.kext, ATIRNDRV and ATINDRV.kext ! Full works QE/CI/OpenGL/Rotation/ on dual DVI !!!
Work DUAL Monitor ! You try!


July 6 2009 !
For 7280 and 7288 - SNOW LEOPARD 10.6 download ATI_X1950Pro(GT)_10a380_without_64bit

REBOOT!!!
Enjoy!

hello,

this is ok for agp card? thanks

[allpro]

this ok  

is ready with a package, ati 7280 10d578, for latest version 10.6.3 ?? very thanks

[chappatti]

TO JAMINMC

A BIG thanks to you.  After agony, there is ecstasy!!   :angel:  

Your kexts work as follow on my x1950Pro in 32-bit + res + QE/CI  device id 7280

** Put your kexts in Extra/Extensions
** Put ATIRadeonX1000...in S/L/E.  (A caveat:  One thing after so much fidgeting with this kext I am not 100% sure where my working one is exactly from !!! ,  But I am leaning heavily towards it being yours.)  
BUT I had to add device id to ATI1900Controller.kext to get full resolution and QE/CI.  Everything else is vanilla. So if anyone else gets screen to work at basic res, adding device to ATI1900Controller may help.  Without this everything is basic.  NO DSDT patch, Nothing else added.

Jaminmc, why is this so?

AND, PLEASE I DO NOT SEE MY HD ON THE DESKTOP....I think this may just be a setting issue on 10.6.3???  since everything else I put on my desktop shows.

A huge thanks again!


EDIT:  I used the following site ( http://www.ltooz.com...os-x-1058--1063 )  to check for QE/CI function, BUT THE QE/CI DOES NOT SHOW IN "About This Mac".  But the tests work. Make sense ??

 Screen_shot_2010_06_11_at_8.02.31_PM.png   1.26MB   105 downloads

[Lanston]

Thanks a lot!
Everything (including my monitor) works just fine!
Live long and prosper!

[ronaldw]

allpro, on Jun 1 2010, 01:57 PM, said:

hello,

this is ok for agp card? thanks

Yes, it is, mine works OK, all resolutions on dual 24 " monitors DVI

[ZPK]

work in 10.6.4 ? who tested ?)))