202 replies to this topic

[slipttees]

I'll try TheStevoKext about GMA X3500...waiting news!


thx

[blackfish]

Thanks to you, I have a working system:

DG35EC Mobo
8 gigs RAM
Nvidia 8400GS (nvinject.kext with KextHelper)
Belkin F5D8050 USB Wifi (Belkin kext installed with KextHelper)
Logitec Wireless USB Mouse
Apple USB keyboard
Chameleon boot on 500GB sata drive
Leopard 10.5.4

I am wondering if anything will break if I run Software Update to get up to 10.5.6?

If so, is there a good process to follow to prep the machine for this?

Thanks again,
Blackfish

[flock44]

Hi Sliptees,

This is my second request. I ve posted my first request on Hackintosh.org on the same topic.

Please respond me....

Below link explains the issue i m facing in detail... I ve posted screenshots of issue n screenshots of BIOS.

http://www.insanelym...p...9096&st=260  

*** (Read the post by flock44)

I ve almost same config of your's

mobo: Intel DG35EC
Processor: Intel Core 2 Duo 2.53 Ghz
Ram: 2 GB
HD Drive: Seagate 400 Gb (SATA) Connected to Sata port (0)
DVD Drive: LG RW 22x (SATA) connected to Sata port (1).


Thnx in Advance....

slipttees, on Dec 15 2008, 09:42 PM, said:

Update 1/7/2009

Intel Board DG35EC Guide

First, we need to prepare the ground.

Get and update with last Bios there

Get DG35EC made me :-) there

OSX86Tools 1.0 Final: there Thx Jedi PCWiz

Chameleon 1.0.11 Installer: there Thx All Chameleon's

Bios Setting:

Main:
	 Advanced:
			 Peripheral Configuration:
						Audio: Enable
							 High Definition Front Panel Audio:  Enable
						On-Board LAN: Enable
						Onboard 1394: Enable
			 Drive Configuration:
						ATA/IDE Mode: Native
						Configure SATA as: AHCI
						Smart: Enable
						Hard Disk Pre-Delay: No
			 Floppy Configuration:
						Diskette Controller: Disable
			 Chipset Configuration:
						PCI Latency Timer: 32
						HPET: Enable
			 USB Configuration:
						Usb Ports: Enable
						Usb Legacy: Enable
	Security:
			  XD: Enable
			  VT: Enable
	Power:
			  EIST: Enable
			  ACPI: S3 State
	 Boot:
			  Boot Configuration: Advanced
				  Boot to removable device: Disable
				  Boot to Network: Disable
				  Usb Boot: Disable
				  Boot usb Device first: Disable
				  Usb Mass Storage Emulation Type: Auto

PS: Use HDD in the SATA0 Port and DVD in the SATA 1 Port

Start cd boot-132...

In darwin screen type Enter,

Typical boot device are 80 (First HD), 81 (Second HD) Enter two-digit hexadecimal boot Device [fe]

Replace the boot cd-132 at the retail dvd! Waiting 10 sec and press Enter, type f8 and type -v

Open Disktutil Create GUID Partition table and Install Mac OS X

Reboot System, Start cd boot-132 again...

In darwin screen type Enter,

Typical boot device are 80 (First HD), 81 (Second HD) Enter two-digit hexadecimal boot Device [fe]

type 80 and press Enter, type -v and Enter

Open boot-132 and mount kexts.img

in the kexts.img folder copy: Intel82566MM.kext, IntelCPUPMDisabler.kext, SMBIOSEnabler.kext, AppleDecrypt.kext to /System/Library/Extensions/

PS: ACPIPS2Nub.kext ApplePS2Controller.kext if you use keyboard and mouse PS2 :-)

after replacing the extensions open the terminal and use:

sudo -s 
 chmod -R 755 /System/Library/Extensions/*
 chown -R 755 /System/Library/Extensions/*
 diskutil repairPermissions /
 touch /System/Library/Extensions/*
 exit
 sudo -k
 exit

Open OSX86Tools or chameleon installer and install "Chameleon EFI" in OS X Volume!

I tried Chameleon installer three times to work !

Reboot and Work Full speed Retail Now, 5 sec startup and 3sec halt   


Drivers update:

Intel 82566DC Ethernet Controller - There
Intel X3500 VGA Driver (Not Test There!) - There
ALC888S = I'm use Azalia Driver, work only two channel !

Thanks f41qu3, a1kon, HotBreeze, and everyone Thanks.

Big Thx onemanstrash :-p

Sorry my pour English!  

[slipttees]

yo bro, u can try my boot-132.iso in first post. Look, Retail Don't Work with MBR Partition Table, only GUID okay ? and dual boot system u neede a bouth HDD and select in bios system in F10 u HDD boot.

good luck!

sorry pour english  

flock44, on Feb 5 2009, 08:20 PM, said:

Hi Sliptees,

This is my second request. I ve posted my first request on Hackintosh.org on the same topic.

Please respond me....

Below link explains the issue i m facing in detail... I ve posted screenshots of issue n screenshots of BIOS.

http://www.insanelym...p...9096&st=260  

*** (Read the post by flock44)

I ve almost same config of your's

mobo: Intel DG35EC
Processor: Intel Core 2 Duo 2.53 Ghz
Ram: 2 GB
HD Drive: Seagate 400 Gb (SATA) Connected to Sata port (0)
DVD Drive: LG RW 22x (SATA) connected to Sata port (1).
Thnx in Advance....

[flock44]

Hey Slipttees,

First of thnx a lot for the reply...

So all i need to do is use ur boot 132.iso (which ive downloaded from ur first post)?

I'll try to use it to boot. I just some how want to get to installation screen. i'll also make sure to change my BIOS settings to those u have mentioned in ur first post.

But can u pls explain me why was this happening? i mean never endin Boot to Hexadecimal Value loop without showin up Retail DVD or Installation screen?

Sorry but just curious to know so that if someone faces the same problem wanned to help them too.... You know it was hell of a experience when i didnt get any help.

Hope you understand... And will post the result's this weekend after using the Boot 132 u made for DG35EC...

Cheers!

slipttees, on Feb 6 2009, 03:28 AM, said:

yo bro, u can try my boot-132.iso in first post. Look, Retail Don't Work with MBR Partition Table, only GUID okay ? and dual boot system u neede a bouth HDD and select in bios system in F10 u HDD boot.

good luck!

sorry pour english  

[slipttees]

yes, use boot-132 from first post, set hdd sata0 dvd sata1, upgrade u bios #0107 necessary windows XP from easely...

waiting news

later

flock44, on Feb 6 2009, 03:03 PM, said:

Hey Slipttees,

First of thnx a lot for the reply...

So all i need to do is use ur boot 132.iso (which ive downloaded from ur first post)?

I'll try to use it to boot. I just some how want to get to installation screen. i'll also make sure to change my BIOS settings to those u have mentioned in ur first post.

But can u pls explain me why was this happening? i mean never endin Boot to Hexadecimal Value loop without showin up Retail DVD or Installation screen?

Sorry but just curious to know so that if someone faces the same problem wanned to help them too.... You know it was hell of a experience when i didnt get any help.

Hope you understand... And will post the result's this weekend after using the Boot 132 u made for DG35EC...

Cheers!

[flock44]

Hey Slipttees,

First of Thankyou so much...

Finally i managed to install Retail Leopard 10.5.6 on my PC. All credit goes to your wonderful Retail DVD Upload & Boot 132 that you've made for DG35EC Mobo's.

I didn't had any problems starting the Installation till Finishing it.

But couple of Problems here Restart, Shutdown Do NOT work. (I dont use sleep however)

And "Intel82566MM.kext" says it was not install properly install again or contact Vendor. No matter how many times i copy tht from Boot 132 CD (mounting Ktexts.img) to Extensions folder. (System/Library)

And Now comes the Chameleon EFI (I tried both OS X Installer & Chameleon EFI) they both installs properly. But when i Restart (i still need Boot 132 CD to boot to Leopard) (Here i have to press "Restart" button since my Restart n Shutdown are not working.)

I haven't checked with Audio Yet. And I Believe Intel82566MM.Ktext belongs to Network.

So now i have a Clean Retail Leopard Installed with Above issues.

Can you please guide me....

Once again thanks for all the solutions...

You Rock...


Updt: Also I use NVidia 8400 GS 512MB. I connect my Monitor (LG 42inches 1080P) with HDMI to DVI cable. is there any driver tht supports my card/Resolution? I tried using UInstaller by PCWiz but not sure.

Also where can i find Azallia (For Audio)

slipttees, on Feb 8 2009, 07:54 PM, said:

yes, use boot-132 from first post, set hdd sata0 dvd sata1, upgrade u bios #0107 necessary windows XP from easely...

waiting news

later

[slipttees]

"But couple of Problems here Restart, Shutdown Do NOT work. (I dont use sleep however)"

Try OpenHaltRestart.kext

"Intel82566MM.kext says it was not install properly install again or contact Vendor. No matter how many times i copy tht from Boot 132 CD (mounting Ktexts.img) to Extensions folder. (System/Library)"

Try new Intel82566MM.kext

"Also I use NVidia 8400 GS 512MB. I connect my Monitor (LG 42inches 1080P) with HDMI to DVI cable. is there any driver tht supports my card/Resolution? I tried using UInstaller by PCWiz but not sure."

Try EFIstring work Fully all resolutions.

"Also where can i find Azallia (For Audio)"

Try get AppleAzaliaAudio.kext. Please, replace this kext and remove AppleHDA.kext from /System/Library/Extensions/

;-) i'm wait reply!


later

[flock44]

Hey Slipttees,

Thanks for the Helpful Response... Will try all of them.

But can u pls provide me how to solve the Boot problem without using Boot 132 CD Everytime?
As i requested/Mentioned in my previous post. No matter how many times i install Chameleon from OSX Tools or Chameleon EFI m not able to get it to work....

Help is Highly Appreciated.

Thnx in Advance...

slipttees, on Feb 10 2009, 05:13 PM, said:

"But couple of Problems here Restart, Shutdown Do NOT work. (I dont use sleep however)"

Try OpenHaltRestart.kext

"Intel82566MM.kext says it was not install properly install again or contact Vendor. No matter how many times i copy tht from Boot 132 CD (mounting Ktexts.img) to Extensions folder. (System/Library)"

Try new Intel82566MM.kext

"Also I use NVidia 8400 GS 512MB. I connect my Monitor (LG 42inches 1080P) with HDMI to DVI cable. is there any driver tht supports my card/Resolution? I tried using UInstaller by PCWiz but not sure."

Try EFIstring work Fully all resolutions.

"Also where can i find Azallia (For Audio)"

Try get AppleAzaliaAudio.kext. Please, replace this kext and remove AppleHDA.kext from /System/Library/Extensions/

;-) i'm wait reply!


later

[slipttees]

i m install chameleon several times, to work from me =-s, maybe ur need new EFI 9/chameleon 1.0.12

try use OSx86tools install chemelon or chameleon installer than

soory my poor english bro

Good Luck!

flock44, on Feb 10 2009, 05:53 PM, said:

Hey Slipttees,

Thanks for the Helpful Response... Will try all of them.

But can u pls provide me how to solve the Boot problem without using Boot 132 CD Everytime?
As i requested/Mentioned in my previous post. No matter how many times i install Chameleon from OSX Tools or Chameleon EFI m not able to get it to work....

Help is Highly Appreciated.

Thnx in Advance...

[jazzman746]

I'm working with Intel DG35EC

I't got me almost crazy... lot of installs but think now it works.

My system:

Mobo Intel DG35EC
CPU Intel core 2 Duo 3GHZ E8400
4 GB ddr2 800Mhz SDRAM
EVGA nvidia 8500gt 512 mb
HDD Maxtor 500GB SATA
DVD TSSTcorp CDDVDW SH-S223F (works like superdrive)
Mouse and Keyboard USB
Flat Panel Syncmaster 2243LNX Samsung 22"

Installed:

xXx 10.5.6 Final Install (released few days ago)
Anv Kernel 9.6.0
-cpumdisabler
-disabler
-biosenabler
-resolver
-open halt restart by psystar
-hardcoded bios Mac Pro

Audio: AppleAzaliaAudio (neither of the 888 sound plugins work), means no microphone

Network: intel8256mm (does not recognized if sleep)

For my video card I used NVINJECT 0.21 521 mb (full working)



That's all.
It works.

[flock44]

UPDATE:

Hey Slipttees ,

Voila...! i finally have 100% working Mac. All working including Network (Intel 82566MM.Kext)
And Audio (AzaliaAudio.pkg) though there's a little glitch in begining with Audio still rocks.

Many thanks to kext Helper which fixed all error with Network & Audio kext files in extensions.

Finally i still couldn't fix Chameleon but do not want to mess with rest of the workin Mac so jus using USB flash drive to boot from boot 132 image. I have no complaints.

Thanks to you who Helped/Guided all the till successful Vanila Install....

Cheers dude...

slipttees, on Feb 11 2009, 06:21 PM, said:

i m install chameleon several times, to work from me =-s, maybe ur need new EFI 9/chameleon 1.0.12

try use OSx86tools install chemelon or chameleon installer than

soory my poor english bro

Good Luck!

[slipttees]

yeah, good job :-)

[flock44]

Hey Slipttees,

Just wanned to knw if you have any idea why i Chameleon or PC EFI are not working on my PC?

I tried new version of Chameleon and even PC EFI v9 no luck....

And what is DSDT Patch for? Does it have to do anything with Chameleon patch? (Srry for Bein noob here)

And any idea when is Newer version of Chameleon is goin to be released? with that cool GUI interface?

Thanx... waiting for your reply...

slipttees, on Feb 17 2009, 08:35 PM, said:

yeah, good job :-)

[flock44]

Hi Slipttees,

I have a lil problem here. My System Profiler (in About this Mac... More Info)

It Model Name as "Mac" And Model Identifier as BLANK. And when i take the GeekBench Test it shows my machine as "Hackintosh".

i Installed a Retail Copy of Leopard. Everything is working fine. Except the info which shows on System Profiler.

Can u pls help me? I want it to show as "Mac Pro" and also as Mac Pro in Geekbench instead AS "HACKINTOSH"

Thnx in Advance....

slipttees, on Feb 17 2009, 08:35 PM, said:

yeah, good job :-)

[kristofr]

slipttees, on Dec 15 2008, 09:42 PM, said:

Update 1/7/2009

Intel Board DG35EC Guide

First, we need to prepare the ground.

Get and update with last Bios there

Get DG35EC made me :-) there

OSX86Tools 1.0 Final: there Thx Jedi PCWiz

Chameleon 1.0.11 Installer: there Thx All Chameleon's

Bios Setting:

Main:
	 Advanced:
			 Peripheral Configuration:
						Audio: Enable
							 High Definition Front Panel Audio:  Enable
						On-Board LAN: Enable
						Onboard 1394: Enable
			 Drive Configuration:
						ATA/IDE Mode: Native
						Configure SATA as: AHCI
						Smart: Enable
						Hard Disk Pre-Delay: No
			 Floppy Configuration:
						Diskette Controller: Disable
			 Chipset Configuration:
						PCI Latency Timer: 32
						HPET: Enable
			 USB Configuration:
						Usb Ports: Enable
						Usb Legacy: Enable
	Security:
			  XD: Enable
			  VT: Enable
	Power:
			  EIST: Enable
			  ACPI: S3 State
	 Boot:
			  Boot Configuration: Advanced
				  Boot to removable device: Disable
				  Boot to Network: Disable
				  Usb Boot: Disable
				  Boot usb Device first: Disable
				  Usb Mass Storage Emulation Type: Auto

PS: Use HDD in the SATA0 Port and DVD in the SATA 1 Port

Start cd boot-132...

In darwin screen type Enter,

Typical boot device are 80 (First HD), 81 (Second HD) Enter two-digit hexadecimal boot Device [fe]

Replace the boot cd-132 at the retail dvd! Waiting 10 sec and press Enter, type f8 and type -v

Open Disktutil Create GUID Partition table and Install Mac OS X

Reboot System, Start cd boot-132 again...

In darwin screen type Enter,

Typical boot device are 80 (First HD), 81 (Second HD) Enter two-digit hexadecimal boot Device [fe]

type 80 and press Enter, type -v and Enter

Open boot-132 and mount kexts.img

in the kexts.img folder copy: Intel82566MM.kext, IntelCPUPMDisabler.kext, SMBIOSEnabler.kext, AppleDecrypt.kext to /System/Library/Extensions/

PS: ACPIPS2Nub.kext ApplePS2Controller.kext if you use keyboard and mouse PS2 :-)

after replacing the extensions open the terminal and use:

sudo -s 
 chmod -R 755 /System/Library/Extensions/*
 chown -R 755 /System/Library/Extensions/*
 diskutil repairPermissions /
 touch /System/Library/Extensions/*
 exit
 sudo -k
 exit

Open OSX86Tools or chameleon installer and install "Chameleon EFI" in OS X Volume!

I tried Chameleon installer three times to work !

Reboot and Work Full speed Retail Now, 5 sec startup and 3sec halt   


Drivers update:

Intel 82566DC Ethernet Controller - There
Intel X3500 VGA Driver (Not Test There!) - There
ALC888S = There

Thanks f41qu3, a1kon, HotBreeze, and everyone Thanks.

Big Thx onemanstrash :-p

Sorry my pour English!  

Is there any way that anyone has found to enable Hardware Virtualization within the above build?  I have been trying to run Parallels 4 and it fails saying that hardware Virtualization is not enabled, however, it is in the BIOS.  I had a similar problem on a BadAxeII, but I can't for the life of me remember how to fix it.  Any ideas?

[maleorderbride]

Errr, is that link working for the BOOT-132 CD for this board?  I click on it and I just get re-directed to the insanely mac homepage.

Can anyone host the file for me?

Thanks!

[flock44]

There u go.... http://www.mediafire.com/?zkyfymogezy (This One made by Slipttees...)


Good Luck...

maleorderbride, on Feb 26 2009, 09:35 PM, said:

Errr, is that link working for the BOOT-132 CD for this board?  I click on it and I just get re-directed to the insanely mac homepage.

Can anyone host the file for me?

Thanks!

[maleorderbride]

flock44, on Feb 27 2009, 06:35 AM, said:

There u go.... http://www.mediafire.com/?zkyfymogezy (This One made by Slipttees...)


Good Luck...

Awesome!  Already have 10.5.6 installed now.  I will see what i can do for kexts now.

hmm..
I can not get the sound or ethernet working.  I tried using OS X86 Tools installer to install the kexts, but no luck. I guess I will try Kext Helper?

Anyone who has it working have specific instructions?

[flock44]

Read the First post... Else download this... (http://www.mediafire.com/?enez1guzz1g) for Audio...

And Find 82566M from Slipttees First post here in this topic. Use KextHelper for Network.

that shud solve ur Netwrok n Audio issues...


Good Luck....

maleorderbride, on Feb 28 2009, 01:02 AM, said:

Awesome!  Already have 10.5.6 installed now.  I will see what i can do for kexts now.

hmm..
I can not get the sound or ethernet working.  I tried using OS X86 Tools installer to install the kexts, but no luck. I guess I will try Kext Helper?

Anyone who has it working have specific instructions?