Jump to content
InsanelyMac Forum
Aaron Potter

VoodooHDA-2.8.8 for Gigabyte GA-Z77MX-D3H [VIA VT2020/VT2021] (El Capitan 10.11.3)

Recommended Posts

Hello, I recently updated my system to El Capitan 10.11.3, although I had always used the VoodooHDA 2.7.2 for VT2021, it started to crash the system once on every boot, so I tried to solve that by upgrading the driver.

I downloaded the VoodooHDA 2.8.8 so I opened side by side the 2.7.2 version and the 2.8.8 version info.plist and did the modifications. Then I installed the kext and renamed the AppleHDA.kext, rebooted and there you go! Everything working and no panic at boot.

I zipped the kext and I am trying to upload it here.

I hope this works for you too.

 

Edit: I couldn't upload it so I link it from pcloud and mega

Edit: I attached the plist file as code.



<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<dict>
<key>BuildMachineOSBuild</key>
<string>11G63</string>
<key>CFBundleDevelopmentRegion</key>
<string>English</string>
<key>CFBundleExecutable</key>
<string>VoodooHDA</string>
<key>CFBundleIdentifier</key>
<string>org.voodoo.driver.VoodooHDA</string>
<key>CFBundleInfoDictionaryVersion</key>
<string>6.0</string>
<key>CFBundleName</key>
<string>VoodooHDA</string>
<key>CFBundlePackageType</key>
<string>KEXT</string>
<key>CFBundleShortVersionString</key>
<string>2.8.8</string>
<key>CFBundleSignature</key>
<string>????</string>
<key>CFBundleVersion</key>
<string>2.8.8</string>
<key>DTCompiler</key>
<string></string>
<key>DTPlatformBuild</key>
<string>4F1003</string>
<key>DTPlatformVersion</key>
<string>GM</string>
<key>DTSDKBuild</key>
<string>12A264</string>
<key>DTSDKName</key>
<string>macosx10.8</string>
<key>DTXcode</key>
<string>0441</string>
<key>DTXcodeBuild</key>
<string>4F1003</string>
<key>IOKitPersonalities</key>
<dict>
<key>VoodooHDA</key>
<dict>
<key>AllowMSI</key>
<true/>
<key>Boost</key>
<integer>1</integer>
<key>CFBundleIdentifier</key>
<string>org.voodoo.driver.VoodooHDA</string>
<key>IOClass</key>
<string>VoodooHDADevice</string>
<key>IOMatchCategory</key>
<string>VoodooHDADevice</string>
<key>IOPCIPrimaryMatch</key>
<string>0x1e208086</string>
<key>IOProviderClass</key>
<string>IOPCIDevice</string>
<key>IOUserClientClass</key>
<string>VoodooHDAUserClient</string>
<key>InhibitCache</key>
<true/>
<key>MixerValues</key>
<dict>
<key>PCM</key>
<integer>90</integer>
<key>Rec</key>
<integer>70</integer>
<key>iGain</key>
<integer>90</integer>
<key>iMix</key>
<integer>0</integer>
</dict>
<key>NodesToPatch</key>
<array>
<dict>
<key>Codec</key>
<integer>2</integer>
<key>Config</key>
<string>0x01014010</string>
<key>Node</key>
<integer>36</integer>
</dict>
<dict>
<key>Codec</key>
<integer>2</integer>
<key>Config</key>
<string>0x01011020</string>
<key>Node</key>
<integer>37</integer>
</dict>
<dict>
<key>Codec</key>
<integer>2</integer>
<key>Config</key>
<string>0x01016040</string>
<key>Node</key>
<integer>38</integer>
</dict>
<dict>
<key>Codec</key>
<integer>2</integer>
<key>Config</key>
<string>0x01012050</string>
<key>Node</key>
<integer>39</integer>
</dict>
<dict>
<key>Codec</key>
<integer>2</integer>
<key>Config</key>
<string>0x0101401f</string>
<key>Node</key>
<integer>40</integer>
</dict>
<dict>
<key>Codec</key>
<integer>2</integer>
<key>Config</key>
<string>0x01a19030</string>
<key>Node</key>
<integer>41</integer>
</dict>
<dict>
<key>Codec</key>
<integer>2</integer>
<key>Config</key>
<string>0x01813070</string>
<key>Node</key>
<integer>42</integer>
</dict>
<dict>
<key>Codec</key>
<integer>2</integer>
<key>Config</key>
<string>0x01a19036</string>
<key>Node</key>
<integer>43</integer>
</dict>
<dict>
<key>Codec</key>
<integer>2</integer>
<key>Config</key>
<string>0x503700f0</string>
<key>Node</key>
<integer>44</integer>
</dict>
<dict>
<key>Codec</key>
<integer>2</integer>
<key>Config</key>
<string>0x01451090</string>
<key>Node</key>
<integer>45</integer>
</dict>
<dict>
<key>Codec</key>
<integer>2</integer>
<key>Config</key>
<string>0x014510a0</string>
<key>Node</key>
<integer>46</integer>
</dict>
<dict>
<key>Codec</key>
<integer>2</integer>
<key>Config</key>
<string>0x404510b0</string>
<key>Node</key>
<integer>47</integer>
</dict>
</array>
<key>Noise</key>
<integer>0</integer>
<key>Vectorize</key>
<true/>
<key>VoodooHDAEnableHalfMicVolumeFix</key>
<false/>
<key>VoodooHDAEnableHalfVolumeFix</key>
<false/>
<key>VoodooHDAEnableMuteFix</key>
<false/>
<key>VoodooHDAEnableVolumeChangeFix</key>
<false/>
<key>VoodooHDAVerboseLevel</key>
<integer>0</integer>
</dict>
</dict>
<key>OSBundleLibraries</key>
<dict>
<key>com.apple.iokit.IOAudioFamily</key>
<string>1.1fc9</string>
<key>com.apple.iokit.IOPCIFamily</key>
<string>2.1</string>
<key>com.apple.kpi.iokit</key>
<string>9.0.0</string>
<key>com.apple.kpi.libkern</key>
<string>9.0.0</string>
<key>com.apple.kpi.mach</key>
<string>9.0.0</string>
<key>com.apple.kpi.unsupported</key>
<string>9.0.0</string>
</dict>
</dict>
</plist>

Share this post


Link to post
Share on other sites
Advertisement

Aaron, can you talk about renaming AppleHDA.kext?  I installed the VoodooHDA kext that you posted, rebooted, and it didn't work.  I assume I have to do this renaming?

 

Thanks!

Jim

Share this post


Link to post
Share on other sites

Aaron, can you talk about renaming AppleHDA.kext?  I installed the VoodooHDA kext that you posted, rebooted, and it didn't work.  I assume I have to do this renaming?

 

Thanks!

Jim

It's a little late maybe to respond to you but if anyone else has this problem, just go to /System/Library/Extensions/ and search for AppleHDA.kext, hit ENTER to rename and then change .kext to something like .kextback then it won't be recognized as a kext so it won't be loaded.

You could delete it also if you like, but I always keep originals.

Share this post


Link to post
Share on other sites

It's a little late maybe to respond to you but if anyone else has this problem, just go to /System/Library/Extensions/ and search for AppleHDA.kext, hit ENTER to rename and then change .kext to something like .kextback then it won't be recognized as a kext so it won't be loaded.

You could delete it also if you like, but I always keep originals.

No.

After system update AppleHDA will appear again.

The better way is to use AppleHDADisabler.kext

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.



  • Similar Content

    • By Gymnae
      This guide guide is a work in progress
       
      Introduction
      The H370 chipset powers 8th generation Core-i CPUs by Intel and is actually much newer than the Z370, even though it name implies otherwise. The H370 requires new approaches compared to the Z370, since it includes newer or different components. An example would be on-die USB 3.1 and WiFi support.
      Since this guide is not a "hold-your-hand-every-step" guide, I assume you know:
      Clover installation and configuration How to create an install medium BIOS configuration and access Have heard of ACPI patching (I'm a newb at this myself)  
      What works
      Sleep (via DSDT edits and emulated NVRAM) on-board Audio (via CloverALC script) Native PM (without any kext or patch) All USB ports iGPU for both acceleration and display dGPU (I'm running an Nvidia GTX 1080)  
      Untested
      NIC --> I'm using WiFi only  
      What doesn't work
      Native NVRAM via AptioMemoryFix.efi DMVT Pre-alloc higher than 64MB (but not necessary)  
      Changes to the guide:
      22.5.18: Added SSDT hot-patching to enable sleep, replacing DSDT static patching as an alternative.
       
      1. Installation
      This guide heavy inspired by the work of /u/corpnewt of /r/hackintosh and his (sorta) Vanilla guide
       
      1.1 Create the install media for MacOS
      Follow this, if you are using a Mac to start off with. If you are totally new to MacOS, then please check the basic guide Creation of an installer media in windows or linux
       
      1.2 Install Clover on the install media
      Using the Clover installer, ensure you are installing to the USB medium you are using for the installer.
      Chose the following options:
      AptioMemoryFix UEFI booting only Install to ESP You have to get your hands on an apfs.efi. A google search can help, or extracting it from the Installer package. Make sure you procure a version matching the MacOS version you are about to install. Place the apfs.efi in drivers64UEFI.
       
      1.2 Adjust the config.plist for the installer
      You can use the config.plist attached as a guideline, but take a look at it before and at least adjust the SMBIOS - otherwise it won't boot.
      Attention: The attached plist contains audio patches introduced by a post-install step. If you run into problems, you might remove those. It also contains a manual slide value, which should normally not be needed, but works fine for me. It is also tuned for usage with an Nvidia Pascal dGPU as main GPU.
       
      The config you create now should serve you nicely for install and running the system.
       
      Take care of adding the following basics:
      SMBIOS: iMac18,3 - You can generate a serial number via Clover Configurator. The creation of a proper SMBIOS is covered in many guides to good extend Look at the graphics section and adjust the injection for Intel to your situation  
      Fixes

      Patches

      Devices

      Graphics

      Kernel and Kext patches
       
      1.3 kexts and friends
      Add the supplied SSDT-UAIC.aml to "patched" - it limits the injected USB Ports to the actual number and ports valid for this board.
       
      Required kexts on "Other":
      FakeSMC.kext IntelGraphicsFixup.kext Lilu.kext When having an Nvidia card: NvidiaGraphicsFixup.kext IntelMausiEthernet.kext in case you're running Ethernet USBInjectAll.kext with the HCI-300-series-injector.kext --> These two should be installed to /L/E after install  
      We are leaving sound out at the moment, this is something for post-install. Please note the absence of Shiki, I don't find it necessary. Video material I tried made use of the iGPU without shiki.
       
      1.4 Check BIOS and install
      You should be ready for install. But before you reboot, please take a look at your BIOS and set it up accordingly (copied from the aforementioned guide and adapted):
      Load Optimized Defaults Disable VT-d setting If your system has Secure Boot Mode, disable it Set OS Type to Windows 8/10 or OtherOS - I have not seen a difference Turn off internal Serial and Parallel port Turn off Network stack for boot Turn off wake-on-lan (for now) Set XHCI Handoff to Enabled Don't enable decode over 4G Depending on your GPU, set priority for boot Set internal GPU to enable Set DMVT pre-alloc to 64MB Set USB legacy to enabled Activate XMP profile 1 f your Ram has it (mine doesn't and I added the timings manually) Set ERP to enable, disable platform power management (I need to do more research if this could be enabled)  
      I've attached my current BIOS config "hack2". You can place that on a fat32 drive (the EFI partition of your install USB drive might be an idea) and see if it loads. It's made for and with the F2 BIOS.
       
      The install itself should be like other MacOS Hackintosh installs with it several reboots and ensuring to select the correct boot device in Clover.
       
      2. Post-install
       
      2.1 Install clover on target
      This is a no-brainer, but install a fresh copy of Clover on your target medium.
       
      During install select again AptioMemoryFix but also additionally
      EmuVariableUefi-64.efi Install RC scripts on target volume because otherwise NVRAM doesn't seem to work
       
      After the install, copy
      config.plist contents of "Other" content of "patched" apfs.efi from drivers64UEFI to your new clover install.
       
      2.1 Edit ACPI for slumber
      Choose one option, not both. The hot-patch is experimental, but for the moment it is stable.
       
      2.1.1 Edit DSDT
      This is necessary only once on initial install and every time, you edit or upgrade the BIOS. The DSDT.aml attached to this post might work for your system or give you a file to compare to. Don't expect it to work for you, though.
      I won't go into the details of DSDT extraction and patching. There are better guides (the linked guide is a rip-off of rehabman's guide from a different forum). Please follow such a guide to extract your ACPI data.
       
      Locate and disassemble the DSDT with the newest iasl binary you can put your hands on, then open it with MacIASL in its newest version you can find (Hint: Here is a good source) You can check if the version is new enough if MacIASL doesn't throw error upon compiling a freshly extracted DSDT.aml or DSDT.dst
       
      Add rehabmans repo (as per linked guide) and apply the following patches:
      Rename _DSM to _XDSM Fix _WAK Arg0 v2 USB3 _PRW 0x6D Skylake (instant wake) Find the CNVW device and remove the _PWR function there.
       
      Compile the DSDT and place it in "patched".
       
      2.1.2 Use SSDT hot-patching
      Instead of having to re-extract and re-patch the DSDT on every BIOS change or update, Hardware change one can also use ACPI hot-patching.
      It's a combination of config.plist patches and an SSDT, which is hot-patched into the ACPI (if I understand the process correctly)
       
      You need to add this SSDT-GPRW.aml to your Clover folder in the designated position at Clover/ACPI/patched You need to add this patch to your config.plist. It goes into the DSDT patch section  
      Note: This works for me, but the patch removes the _PRW method from all devices in the DSDT. This could have side-effects. So far, I have seen none. At the moment I'm also not applying any other patch, compared with the additional edits I made to the DSDT method before.
       
      2.2 Install kexts to system
      As mentioned in the install section, it's better to follow rehabman's instruction and install USBinjectAll.kext to /L/E:
      sudo cp -R Release/USBInjectAll.kext /Library/Extensions sudo touch /System/Library/Extensions && sudo kextcache -u / 2.3 Enable onboard Audio
      This is where I'm not so happy currently, I'd like it to work without altering AppleHDA. But currently I find no other way.
       
      2.3.1 Install FakePCIID & FakePCIID_Intel_HDMI_Audio
      Rehabman tells us to use a kext installer to install it to /S/L/E. Chose the RELEASE folder
       
      2.3.2 Run CloverALC command
      Ensure your EFI partition is mounted before running this command
      Get the newest version of CloverALC command (audio_cloverALC-xxx.sh) and run it. Our Audio codec is RTL887 and I'm running with layout ID 1
       
      2.4 Optional steps
      If you have a dGPU, now it's the time to install its drivers and adjust the config.plist for it.
      This is out of scope of this guide. Yet, my supplied config.plist is ready to be used with Nvidia Pascal cards and using the Nvidia web driver.
       
      3. ToDo
      Move away from static DSDT patching to SSDT hotpatching --> requires my work Native NVRAM --> requires developer work Audio without AppleHDA patching --> requires developer work  
      4. Thanks to
      @MaLd0nfor helping finding the right way with the DSDT
      @RehabMan, for being a legend and helping me out patching
      @toleda, for audio patches for the 300 series
      /u/corpnewt, for his superb vanilla guide
      @wmchris for his super XPS 9550 guide and introducing me to hot-patching
      all the developers of clover and it's awesomeness
       
      SSDT-UIAC.aml
      config.plist
      DSDT.aml
      hack2
    • By MaLd0n
      ***The topic is for Notebooks and Desktops***   First... ***Update bios to last available version!***   If you need DSDT edits for SkyLake, KabyLake or CoffeeLake... -Extract tables with F4 key in Clover boot screen! -Run it and send me files! RunMe.app   This guide is not a step by step, if you need one, see here   Look at my Clover folders and understand what we really need, this is the best way to learn     1-Installation     --Create a bootable copy of macOS Sierra Check out the link http://www.insanelymac.com/forum/files/file/559-flash-drive-maker/   --Create a bootable copy of macOS HighSierra Check out the link http://diskmakerx.com/   --Install Clover in USB stick https://sourceforge.net/projects/cloverefiboot/files/Installer/   --Replace with my Clover folder  -Serie 100/200/300 CLOVER Install.zip   --Install Sierra/High Sierra and boot into system! 2-Post Installation     --Install Clover in HDD/SSD and replace with my folder -Serie 100/200/300 CLOVER Post Install.zip   --Reboot and activate video!   3-Video     -Nvidia WebDriver Sierra http://www.insanelymac.com/forum/topic/312525-nvidia-web-driver-updates-for-macos-sierra-update-07212017/ -Nvidia WebDriver High Sierra http://www.insanelymac.com/forum/topic/324195-nvidia-web-driver-updates-for-macos-high-sierra-update-10162017/ -Cuda http://www.insanelymac.com/forum/topic/302795-cuda-90214-is-out-update-10162017/ -Check it, easy way nvidia-update.command.zip by Benjamin-Dobell   4-DSDT     --DSDT mobo GA Z270 Gaming K3 DSDT.MaLd0n Gigabyte GA Z270 Gaming K3.zip   --DSDT mobo Asus ROG STRIX Z370 F Gaming DSDT.MaLd0n Asus ROG STRIX Z370 F Gaming.zip   --DSDT mobo Asus ROG Strix Z370-G Gaming DSDT.Asus ROG Strix Z370-G Gaming.zip   --DSDT mobo GA Z170XP SLI DSDT.MaLd0n GA Z170XP SLI.zip   --DSDT mobo ASROCK Z170  EXTREME 7 DSDT.MaLd0n ASROCK Z170 EXTREME 7.zip   Patches -FIX ERRORS AND WARNINGS -HPET -SATA -DMAC -SLPB -DARWIN -LPC* -XHCI -PLUGIN TYPE -HDAS to HDEF -HDEF -RTC -IRQs -SBUS* -BLC0 -BUS1 -MCHC -ALS0 -SHUTDOWN -LAN -USBX -PMCR -IMEI -EC -PNLF(Nvidia/AMD) -HDMI ---To avoid problems use some patches in config.plist, don't forget!--- GLAN to GIGE 474c 414e 4749 4745 GFX0 to IGPU 47465830 49475055 HDAS to HDEF 48444153 48444546 HECI to IMEI 48454349 494d4549 SAT0 to SATA 53415430 53415441 5-SSDT   Generate your SSDT for PM, use ssdtPRGen by Piker-Alpha https://github.com/Piker-Alpha ssdtPRGen.command.zip   or just use "plugin-type"=0x01 in DSDT, SSDT or Clover config.plist   for check Power, Frequency, Temperature and Utilization, use it Install Intel Power Gadget.pkg.zip   6-Brightness  
      Install .app, select the required permission and reboot. Work in F1 / F2 keys!
      NativeDisplayBrightness.app.zip


      https://github.com/Bensge/NativeDisplayBrightness/releases
      *in some cases .app don't work, check patches in config.plist inside Clover folder Post Install
        -Clover   https://sourceforge.net/projects/cloverefiboot/files/Installer/   -Lan driver by Mieze     -Atheros http://www.insanelymac.com/forum/files/file/313-atherose2200ethernet/   -Intel http://www.insanelymac.com/forum/files/file/396-intelmausiethernet/   -Realtek http://www.insanelymac.com/forum/files/file/88-realtekrtl8111-binary/   -Links     -FakeSmc https://bitbucket.org/RehabMan/os-x-fakesmc-kozlek   -Audio https://github.com/vit9696/AppleALC http://www.insanelymac.com/forum/topic/293863-applehda-patch-requests/   -USB https://bitbucket.org/RehabMan/os-x-usb-inject-all/downloads   if u like, Rate Topic     It's time to Rock -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!   Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Apple, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad, badruzeus and many, many, many others!   We're all here to have fun and learn from each other!   ENJOY!  
    • By MaLd0n
      Nehalem, SandyBridge, IvyBridge, Haswell, Broadwell     Skylake, Kabylake and Coffeelake is here http://www.insanelymac.com/forum/topic/321872-guide-sierra-on-gigabyte-mobos-serie-200-kabylake-dsdt/   First...   ***Update bios to last available version!***   If you need a full patched DSDT...  -Extract tables with F4 key in Clover boot screen! -Run it and send me files! RunMe.app   Installation   --Create a bootable copy of macOS Sierra Check out the link http://www.insanelymac.com/forum/files/file/559-flash-drive-maker/   --Create a bootable copy of macOS HighSierra Check out the link http://diskmakerx.com/   --Install Clover in USB stick https://sourceforge.net/projects/cloverefiboot/files/Installer/   --Replace with my Clover folder CLOVER Install.zip   --Install Sierra/High Sierra and boot into system!   Post Installation --Install Clover and replace with my folder CLOVER Post Install.zip   --Reboot and activate video!   Bingo!   Now you need a fine tune! DSDT time!   --DSDT   Patches -FIX ERRORS AND WARNINGS -HPET -SATA -DMAC -SLPB -DARWIN -LPC -XHCI -PLUGIN TYPE -XXXX to HDEF -HDEF -RTC -IRQs -SBUS -BUS1 -MCHC -ALS0 -SHUTDOWN -LAN -USBX -PMCR -EC -PNLF -HDMI
       
      --Power Management
      - 1 Generation Intel Processors, use Generate P and C States in config.plist
      - 2 and 3 Generations Intel Processors, Generate SSDT with Piker script and drop CpuPm and Cpu0Ist SSDTs
      ssdtPRGen.command.zip
      Credits-https://github.com/Piker-Alpha/ssdtPRGen.sh
      - 4 Generation+ Intel Processors, use PluginType=1 in DSDT, SSDT or Clover config.plist
       
      for check Power, Frequency, Temperature and Utilization, use it
      Install Intel Power Gadget.pkg.zip
       
      --Brightness
      Install .app, select the required permission and reboot. Work in F1 / F2 keys!
      NativeDisplayBrightness.app.zip


      https://github.com/Bensge/NativeDisplayBrightness/releases
      *in some cases .app don't work, check patches in config.plist inside Clover folder Post Install
       
      --Clover
       
      https://sourceforge.net/projects/cloverefiboot/files/Installer/
       
      --AUDIO
       
      Use DSDT + AppleAlc
       
      --install Lan driver by Mieze
        -Atheros http://www.insanelymac.com/forum/files/file/313-atherose2200ethernet/   -Intel http://www.insanelymac.com/forum/files/file/396-intelmausiethernet/   -Realtek http://www.insanelymac.com/forum/files/file/88-realtekrtl8111-binary/   --Links   -FakeSMC https://bitbucket.org/RehabMan/os-x-fakesmc-kozlek   -Audio https://github.com/vit9696/AppleALC http://www.insanelymac.com/forum/topic/314406-voodoohda-289/   -USB https://bitbucket.org/RehabMan/os-x-usb-inject-all/downloads   It's time to Rock   -Credits and thanks to the old and new people in the community who developed patches, kexts and bootloaders!   Apple, Slice, Kabyl, usr-sse2, jadran, Blackosx, dmazar, STLVNUB, pcj, apianti, JrCs, pene, FrodoKenny, skoczy, ycr.ru, Oscar09, xsmile, SoThOr, RehabMan, Download-Fritz, Zenit432, cecekpawon, Intel, Oracle, Chameleon Team, crazybirdy, Mieze, Mirone, Oldnapalm, netkas, Elconiglio, artut-pt, ErmaC, Pavo, Toleda, Master Chief and family, bcc9, The King, PMheart, Sherlocks, Micky1979, vit9696, vandroiy2013, Voodoo Team, Pike R. Alpha, lvs1974, Austere.J, CVad and many, many, many others!   We're all here to have fun and learn from each other!  
    • By DapperDuck
      Quite the title I have chosen for this topic no?
       
      I got my Hackintosh up and running since yesterday. I followed this topic
       and used @MaLd0n 's CLOVER.zip files for kext installation and for the included SSDT's and DSDT. Massive thanks for that btw.
       
      The only *slight* problem I still have is when I have XMP set to profile 1 in the Gigabyte BIOS, and I put my Hackintosh to sleep and I wake it up, I get the message that all USB drives were not ejected properly.
       
      I really don't understand what's causing this problem. I currently have disabled XMP in the BIOS and the USB drives are not getting ejected when my Hack wakes from sleep.
      I use 16GB of Corsair DDR4 Vengeance ram which goes up to 3000MHz. I have XMP profile in CLOVER set to 1. About this Mac reports that my RAM speed is 2998 Mhz. I have a separate SSD drive with Windows on it and I do not think it utilises the full MHz of the RAM because XMP is disabled. 
       
      Hopefully someone is able to help me.
       
      Hackintosh specs:
      Gigabyte Aorus ultimate gaming 
      i7-8700k
      Corsair Vengeance DDR4 3000Mhz RAM (16GB)
      Nvidia GTX 1080
      System def: iMac 18,3
       
      I have my config.plist in the attached files. Hope this gives enough insight. 
      config.plist
    • By coscos
      I recently set up my hackintosh. Everything else works fine, the only issue is my monitor cannot come back from sleep.
      Symptom: 
      If I click the "sleep" menu manually, the system goes to sleep fine. After the system sleeps for a while (more than a few mins, I guess it's called "deep sleep"), when I try to wake it up, the monitor wakes up but stays black screen. The machine is on. If I leave the system to time out and sleep by itself, only the monitor goes off; when I try to wake it up, same symptom as above.
      What I have tried (but none worked):
      additional boot flag: ngfxpatch=pikera additional boot flag: darkwake = 0 Customize EDID
      Specs:
      Motherboard: Gigabyte Z77x-UD5H BIOS: F16j CPU: Ivy Bridge i5-3570K CPU @ 3.40GHz (quad core) Graphics: Nvidia GTX 1050 Monitor: Dell P2715Q @ 4k / 60Hz, Display Port Wifi / Bluetooth: BCM94360CS with PCIE Onboard GPU: disabled OS: High Sierra 10.13.3
      Please see attached for following files:
      EFI zip file: https://www.dropbox.com/s/8nun37msu9b1bva/EFI.zip?dl=0 I generated my own SSDT.aml using ssdtPRGen.sh; Other SSDT patches are copied from this repository: https://github.com/VoiletDragon/Z77X-UD5H-Clover-Hotpatch-Patches ioreg dump: https://www.dropbox.com/s/5a10k82guczaaws/macchiato.ioreg.zip?dl=0 result from following command: https://www.dropbox.com/s/0b22qcw79ovnjdg/kext-touch.txt.zip?dl=0 kextstat|grep -y acpiplat kextstat|grep -y appleintelcpu kextstat|grep -y applelpc kextstat|grep -y applehda sudo touch /System/Library/Extensions && sudo kextcache -u /
      I am looking forward to your suggestions. Thanks.
×