ChecksumCharlie Posted August 17, 2005 Share Posted August 17, 2005 What's up. Posting this topic in order to obtain further information on running OSx86 on Xeon platforms. Not much info other than I have not been successful in booting up OSx86 at all. I constantly get kernel panics. These are some screens of my attempts at running this with various commands: http://www.geocities.com/checksumcharlie/panic_acpi.gif http://www.geocities.com/checksumcharlie/panic_x86pc.gif http://www.geocities.com/checksumcharlie/panicx86.gif I have tried running it with the following: -x -v acpi=off platform=X86PC Nothing works so far. I'm running on a dual Xeon 2.0Ghz Prestonia with sse2 and HT on a Asus PCDL Deluxe board, Intel 875p chipset. 1gb ram. Some people from the irc chan have also said they cannot run it on a Xeon CPU. If anyone else has the same problem or if anyone is able to run it please post your screenshots, system specs, and your methods here! Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/ Share on other sites More sharing options...
gamoul Posted August 17, 2005 Share Posted August 17, 2005 Hi. I succeded running OSX on my Dual 1.7Ghz Xeon SSE2 (HP X4000). It's slow (only 128Mb RAM) and buggy but it works. I Just used dd.exe to clone the vmware image from my windows HD to an other HD, and applied the SSE3->SSE2 patch. I have a Radeon 9800 pro, i need to set the computer bios to 16Mb VRAM only to do a normal boot. Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-2652 Share on other sites More sharing options...
p0lar Posted August 17, 2005 Share Posted August 17, 2005 DP533S, 2x2.8GHz Xeons @ 533MHz FSB, 2GB PC2700, Ti4600 -- pure panic Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-2681 Share on other sites More sharing options...
hardboiledwonderland Posted August 18, 2005 Share Posted August 18, 2005 I have an IWill DH800 board running dual Xeons @ 2.8Ghz (Nocona processors- 800FSB, SSE3). Graphics are Radeon 9500 Works fine. Built-in NIC works. OS X states number of CPUs as 2. I should check the graph but I assume it would list 4 threads as I have hyperthreading enabled. Haven't tested sound. DD'ed the deadmoo image. Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-2792 Share on other sites More sharing options...
Guest Posted August 18, 2005 Share Posted August 18, 2005 I'm running on a dual Xeon 2.0Ghz Prestonia with sse2 and HT on a Asus PCDL Deluxe board, Intel 875p chipset. 1gb ram. I have the same mobo running 2.8 GHz Xeons and have exactly the same problem in VMWare. Really, really annoying. Works fine on my P4 1.7GHz machine, though, so I have been able to play with it... Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-2827 Share on other sites More sharing options...
ChecksumCharlie Posted August 18, 2005 Author Share Posted August 18, 2005 Hmm, seems like the chipset doesn't have much to do with it running or not cuz some of us can run on Intel 875P and some cannot. Well I managed to get a little further than the panic using the -f switch, but not further than some loading. Screenshot of loading: http://www.geocities.com/checksumcharlie/load.gif But system halts on some type of I/O error: "SAM Multimedia: READ or WRITE failed, ASC = 0x24, ASCQ = 0x00" http://www.geocities.com/checksumcharlie/halt.gif Looks like it could be a prob with the hd img. Just curious to the people that could not get it to work, were you using VMWare at the time? It seems like the people that got it running did it natively. I myself am running it through vmware, which could be the prob. So to everyone that got the panics try to use -f and -v and see how far you get on that load and post results. Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-2959 Share on other sites More sharing options...
Guest Posted August 18, 2005 Share Posted August 18, 2005 So to everyone that got the panics try to use -f and -v and see how far you get on that load and post results. Just tried that and I got further too. I removed everything except hard disk and memory from the VMWare machine config, and in the VMWare BIOS setup (F2 on boot) I disabled the floppy drive, serial ports, and parallel port to minimize device issues. Upon starting with "-f -v" I got a TON (several pages) of "Loading HFS+ file: xxxxx" messages, then the graphics mode changed and some more stuff happened, with processing terminating with the error shown in the attached pic. Not sure if this is progress... Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-3131 Share on other sites More sharing options...
earion Posted August 18, 2005 Share Posted August 18, 2005 Hey guys i managed to get native to work on my xeon platform, here are my specs: NCCH-DL, 2x Xeon 2.8 (Nocona) 1gb DDR400 PNY quadro 750xgl Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-3140 Share on other sites More sharing options...
ChecksumCharlie Posted August 18, 2005 Author Share Posted August 18, 2005 Yea it seems like when run in vmware it runs into some type of hd i/o errors. Everyone that gets it going does it via native boot. perhaps vmware just doesn't handle smp or ht correctly or something not sure. I guess you guys are better off trying to dd or clone your image onto a spare hd. I can't do that right now cuz im strapped for hd space. probably when I get a dvd burner and free up some space ill be able to do that. If anyone running on a Xeon actually gets this to go on a vm machine please post some pics and your method of getting it going. Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-3217 Share on other sites More sharing options...
ChecksumCharlie Posted August 18, 2005 Author Share Posted August 18, 2005 Ok, trying to repleace the kernel using 'maxxuss' instructions, however i cannot seem to access the cd drive. does anyone know the dev name for the cdrom under darwin? Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-3224 Share on other sites More sharing options...
joostpossemiers Posted August 19, 2005 Share Posted August 19, 2005 cd under OS X: /dev/disk1s1 Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-3310 Share on other sites More sharing options...
hardboiledwonderland Posted August 19, 2005 Share Posted August 19, 2005 Worked under WMware for me using the deadmoo image. I had to boot safe mode, I think. Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-3486 Share on other sites More sharing options...
learning_bird Posted August 19, 2005 Share Posted August 19, 2005 Please, report more of your experiences with Xeons in terms of speed and stability. Those that have double Xeons, does OSXx86 recognizes both CPUs? Those applications that are optimized for multiple CPUs ( like Photoshop, Final Cut, Mathematica and many others ) really use the 2nd processor and work fast? Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-3558 Share on other sites More sharing options...
trellix78 Posted September 1, 2005 Share Posted September 1, 2005 Trying to boot natively on: ASUS PC-DL 2x Prestonia 2Ghz 1 Gb DDR 333 with hard disk attached alone on primary IDE channel doesn't work with options "-f -v -x" The screen scrolls by with a bunch of "Loading..." messages and then gives this error: "BSD root: disk0s1, major 14, minor 1 Load of /sbin/launchd, errno 86, trying /sbin/mach_init Load of /sbin/launchd failed, errno 86" Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-10676 Share on other sites More sharing options...
Riot Nrrrd™ Posted September 1, 2005 Share Posted September 1, 2005 The screen scrolls by with a bunch of "Loading..." messages and thengives this error: "BSD root: disk0s1, major 14, minor 1 Load of /sbin/launchd, errno 86, trying /sbin/mach_init Load of /sbin/launchd failed, errno 86" The kernel loaded somehow, but it wasn't able to mount the root filesystem - it didn't find the Launch Daemon, nor (apparently) could it find the Mach kernel. Or else it mounted the filesystem but neither of those was in there, which is far less likely. Now why that happened, is anybody's guess ... Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-10733 Share on other sites More sharing options...
trellix78 Posted September 1, 2005 Share Posted September 1, 2005 I attached the exact same laptop hard disk from PC-DL system to my Dell D610 and it loads and runs like greased lightning without even using safe mode. Look at the attached image for a screenshot. Specs for the Dell D610 are in the image but I'll give it here again: Pentium M 1.86 Ghz 1 GB DDR2 RAM Intel 915GM graphics AC '97 sound Broadcom NetXtreme 57xx Gigabit Ethernet Controller Intel PRO 2200BG Wireless Intel 82801 USB 2.0 Everything seems to work but my USB mouse and the network. I suspected Broadcom Gigabit would give problems. There might be a chance the wireless will work. If it can't connect to the network, it's useless to me. It looks like there really is a genuine problem with Intel Xeon Prestonia chips then. I'll try to source at least one Nocona Xeon to get the greased lightning effect on my workstation. Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-10835 Share on other sites More sharing options...
maddeepee Posted September 21, 2005 Share Posted September 21, 2005 Any news here? Someon successful with Asus PCDL? Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-18086 Share on other sites More sharing options...
longview Posted September 22, 2005 Share Posted September 22, 2005 Just for the record: VMware doesnt handle HFS+ correctly so using patched iso as cd will fail. Release 1 seems to break platform=X86PC/ACPI. Those trying in VMware should try to burn the cd and mount the station in VMware or try it native. Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-18180 Share on other sites More sharing options...
gimpyviper Posted September 22, 2005 Share Posted September 22, 2005 I tried everything myself, same setup Asus PC-DL deluxe with 2 x 2GHZ Xeon Prestonias. Tried it with HT on and off, ACPI on and off etc etc etc tried everything and didn't get anywhere with it. I have no idea what it could be but when I tried it with HT off and a platform command I think I got an error that said unsupported CPU or something like that.... Eitherway, I guess it doesn't matter since I'm replacing my dual xeon rig with a dual opteron one. Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-18279 Share on other sites More sharing options...
kite Posted October 3, 2005 Share Posted October 3, 2005 Here almost everything works. : Dell sc1420 with 3Ghz Nocona, 1.5GB RAM, Radeon x700 512MB. I need to manually start dock.app and some of the menu items, to get in touch with the desktop and such. Without starting these I have only contact with finder trough the finderwindows. There is a few irritating bugs though, Safari is repeting this message while trying to use autocomplete or something: A keychain cannot be found to store "kite." ...as example. (options shown is: Cansel/Reset to Defaults) There is no response when I trying to: Force Quit Sleep Restart Turn off Cannot get in to loginitems, there is a funny message though: "You cannot change login items because Login items" Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-20300 Share on other sites More sharing options...
TriHFH Posted October 14, 2005 Share Posted October 14, 2005 Just got it installed using the marklar dvd patched w/ release 1.... flawless. It boots up (without safemode) with no errors and everything works. Sound works, network card works, haven't noticed any bugs... I'm using a Dell Precision 670 Workstation. It has: 3.6GHz Intel Xeon (Nocona) 2GB DDR2 ECC ram Integrated AC97 Audio Intel network card.. Intel chipset... i believe it is E7252 or something close to that Anyways, it's a complete success. I get a 42.59 using xbench xeon.tiff xbench.txt Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-22149 Share on other sites More sharing options...
tocnet Posted November 22, 2005 Share Posted November 22, 2005 hi, My first try in install MacOS Fail. The error message (kernell Panic) is like: Not found Driver for this hardware "ACPI" after Kernel Panic So I try other flags how -v -x -F -Platform=ACPI or X86PC. And try disable USB,LPT,COM,AUDIO,ETHERNET. My MacX86 DVD is a combo X86 and PPC of version 10.4.3 2.9GB Leter i put the torrent name. Nothing work. My computer is a Workstantion Dell precision 470 Dual Xeon 2.8 Ghz L2 1MB 1GB ECC DDR400 SCSI 320 how this information don't tell much I put /proc/* for tell more. Processor NOCONA processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 4 model name : Intel® Xeon CPU 2.80GHz physical id : 0 siblings : 2 runqueue : 0 stepping : 1 cpu MHz : 2793.263 cache size : 1024 KB fpu : yes fpu_exception : yes cpuid level : 3 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss tm ferr syscall nx lm sse3 monit or ds-cpl cnxt-id bogomips : 5570.56 clflush size : 64 address sizes : 36 bits physical, 48 bits virtual power management: PCI devices found: Host bridge: PCI device 8086:359e (Intel Corp.) (rev 9). Class ff00: PCI device 8086:3591 (Intel Corp.) (rev 9). PCI bridge: PCI device 8086:3595 (Intel Corp.) (rev 9). PCI bridge: PCI device 8086:3596 (Intel Corp.) (rev 9). PCI bridge: PCI device 8086:3597 (Intel Corp.) (rev 9). USB Controller: Intel Corp. 82801EB USB (rev 2). USB Controller: Intel Corp. 82801EB USB (rev 2). USB Controller: Intel Corp. 82801EBUntitled 1 USB (rev 2). USB Controller: Intel Corp. 82801EB USB (rev 2). USB Controller: Intel Corp. 82801EB USB2 (rev 2). PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev 194). ISA bridge: Intel Corp. 82801EB LPC Interface Controller (rev 2). OK HLCPart: IDE interface: Intel Corp. 82801EB Ultra ATA Storage Controller (rev 2). SMBus: Intel Corp. 82801EB SMBus Controller (rev 2). OK HLCPart: Multimedia audio controller: Intel Corp. 82801EB AC'97 Audio Controller (rev 2). (ICH5/ICH5R) PCI bridge: PCI device 8086:0329 (Intel Corp.) (rev 0). PCI bridge: PCI device 8086:032a (Intel Corp.) (rev 0). RAID bus controller: Adaptec ASC-39320( U320 w/HostRAID (rev 16). Ethernet controller: PCI device 8086:1026 (Intel Corp.) (rev 4). VGA compatible controller: (nVidia Corporation) (rev 162). (NVS280) This is a Quadro Vesa 3.0 Is my Install DVD the problem? Help. tks. Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-30142 Share on other sites More sharing options...
pyrotek Posted November 22, 2005 Share Posted November 22, 2005 Another one here with xeon issues. Dual 3.0gig xeon, PC-Dl 3gig ram No install in VMware 5.0 at all I get this Error. ""BSD root: disk0s1, major 14, minor 1 Load of /sbin/launchd, errno 86, trying /sbin/mach_init Load of /sbin/launchd failed, errno 86" " I tried a few different files that I’ve found on the net all with the same resault. I've got some time to mess with this if anyone’s got any thoughts on how to fix it I am quite willing to help I don't have the spare for another computer in the house otherwise I would do it native. So VMware is must. Anyone know the exact reason why OSx will not like the Prestonia core? Thanks everyone! Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-30176 Share on other sites More sharing options...
MaddMan79 Posted November 22, 2005 Share Posted November 22, 2005 Ok, I've personally tested the following Xeon cores: Prestonia... failed! Nocona... success! Gallatin... failed! I want to know if anyone here has personally tested the Irwindale and Willamette cores. Please let me know if you had any luck. -Brian Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-30225 Share on other sites More sharing options...
tocnet Posted November 23, 2005 Share Posted November 23, 2005 Ok, I've personally tested the following Xeon cores: Prestonia... failed! Nocona... success! Gallatin... failed! I want to know if anyone here has personally tested the Irwindale and Willamette cores. Please let me know if you had any luck. -Brian Intel and yours names. The next Xeon can call Björk. The processor comes in format of Duck. Link to comment https://www.insanelymac.com/forum/topic/387-osx86-on-xeon/#findComment-30353 Share on other sites More sharing options...
Recommended Posts