dude998866 Posted October 15, 2008 Share Posted October 15, 2008 I have Cpmpaq PC that I have managed to install 10.4.8 on. Everthing works (I'm using it to write this). The only problem is the Grphics. As the title states It uses an Intel 845GV graphics set. The settings are currently stuck at 1024X768 @ (appears to be) 65HZ without QE. Now there are currently no KEXT's loaded for this. So bassically are there any drivers for this? or are there any files that I can modify to make this work. Thanx for all help in advance Link to comment Share on other sites More sharing options...
dude998866 Posted October 16, 2008 Author Share Posted October 16, 2008 anyone? Link to comment Share on other sites More sharing options...
dude998866 Posted October 16, 2008 Author Share Posted October 16, 2008 Somebody must have an idea.... Link to comment Share on other sites More sharing options...
Nick14 Posted October 16, 2008 Share Posted October 16, 2008 theres drivers for only qe from mthe 10.4.3 cd it's for intel extreme driver Link to comment Share on other sites More sharing options...
dude998866 Posted October 16, 2008 Author Share Posted October 16, 2008 Ok, so what files do I need, and were can I find them? Thank you so much for actually replying. Link to comment Share on other sites More sharing options...
djmastera2000 Posted October 16, 2008 Share Posted October 16, 2008 As far as i know there is no possibility to get GMA 8xx to work on Tiger after 10.4.1...simply no more driver included. Link to comment Share on other sites More sharing options...
dude998866 Posted October 17, 2008 Author Share Posted October 17, 2008 why can't the kexts from the 10.4.1 driver be copied into 10.4.11 Link to comment Share on other sites More sharing options...
djmastera2000 Posted October 17, 2008 Share Posted October 17, 2008 Simple point: incompatibility Link to comment Share on other sites More sharing options...
dude998866 Posted October 18, 2008 Author Share Posted October 18, 2008 Is there a config file I can edit to get it above 60HZ? I can thive for the time being without QE but 60HZ is just too hard on the eyes. Link to comment Share on other sites More sharing options...
iNoob Posted October 18, 2008 Share Posted October 18, 2008 1st: Buy a flat panel 2nd: read below 1. download http://www.esnips.com/doc/6a108a83-2910-42...0-and-IIG-Kexts 2. http://forum.insanelymac.com/index.php?sho...2868&hl=830 I don't guarantee if that will work Link to comment Share on other sites More sharing options...
dude998866 Posted October 20, 2008 Author Share Posted October 20, 2008 Doesn't this only work for 10.4.1? Link to comment Share on other sites More sharing options...
djmastera2000 Posted October 20, 2008 Share Posted October 20, 2008 Doesn't this only work for 10.4.1? Yes, i think so too... Link to comment Share on other sites More sharing options...
dude998866 Posted October 20, 2008 Author Share Posted October 20, 2008 Damn, I was hopefull for a moment. Link to comment Share on other sites More sharing options...
dude998866 Posted October 21, 2008 Author Share Posted October 21, 2008 What if I were to take the 9xx drivers and place the 8xx hardware ID into them... could that produce QE results? Also I managed to change the refresh rate by editing com.apple.Boot.plist and adding the lines <key>Graphics Mode</key> <string>1024x768x32@85</string> This at least makes it easier on the eyes than 60Hz and therefore a little more usable. Link to comment Share on other sites More sharing options...
riws Posted October 21, 2008 Share Posted October 21, 2008 What if I were to take the 9xx drivers and place the 8xx hardware ID into them... could that produce QE results? No QE, but Resolutions and Hz are possible so. Link to comment Share on other sites More sharing options...
Recommended Posts