mindstate Posted April 18, 2015 Share Posted April 18, 2015 Hello All, I am new here, glad to be here and to have a compatible machine for hackintosh. I have successfully install Mavericks into my HP 8440p with Intel HD Graphics GPU. It boots fine, with the usb installer still plugged in. I tried to install Clover_v2.3k_r3193, choosing options - UEFI Install for booting only - Install Clover in the ESP - Bluemac Theme - Install RC Scripts on target volume - Install Clover preference pane Choosing these options i reboot and my computer attempts to boot in network mode. Im new with this stuff any guidance on how to properly install clover to my HP 8440p? Thank you so much! Quote Link to comment Share on other sites More sharing options...
anonymousnbs Posted April 19, 2015 Share Posted April 19, 2015 Hello All, I am new here, glad to be here and to have a compatible machine for hackintosh. I have successfully install Mavericks into my HP 8440p with Intel HD Graphics GPU. It boots fine, with the usb installer still plugged in. I tried to install Clover_v2.3k_r3193, choosing options - UEFI Install for booting only - Install Clover in the ESP - Bluemac Theme - Install RC Scripts on target volume - Install Clover preference pane Choosing these options i reboot and my computer attempts to boot in network mode. Im new with this stuff any guidance on how to properly install clover to my HP 8440p? Thank you so much! mount EFI and copy all file in usb to > EFI ( Hard disk drive ) and u need add boot options 1 Quote Link to comment Share on other sites More sharing options...
Allan Posted April 19, 2015 Share Posted April 19, 2015 Hello and Welcome to InsanelyMac. Take a good read here: UEFI multi boot with Clover 1 Quote Link to comment Share on other sites More sharing options...
mindstate Posted April 19, 2015 Author Share Posted April 19, 2015 Thanks for the direction guys! i understand what i have to do now..thanks a bunch 1 Quote Link to comment Share on other sites More sharing options...
mindstate Posted April 20, 2015 Author Share Posted April 20, 2015 Still having a problem with Clover booting to blank screen..doesnt matter if use Clover USB or the installed one on my hard drive. The way i can boot to my system is using the Mavericks Installer i used.. I tried to add the FakeSMC.kext still didnt work..any suggestions? Quote Link to comment Share on other sites More sharing options...
Allan Posted April 20, 2015 Share Posted April 20, 2015 You can't add FakeSMC where? And boot with -v, if you have any errors, take a photo and put here. Quote Link to comment Share on other sites More sharing options...
mindstate Posted April 21, 2015 Author Share Posted April 21, 2015 i guess it sticks there..and my usb stick stays inactive too Quote Link to comment Share on other sites More sharing options...
Allan Posted April 21, 2015 Share Posted April 21, 2015 Remove OsxAptioFixDrv-64.efi inside your USB installation Quote Link to comment Share on other sites More sharing options...
mindstate Posted April 21, 2015 Author Share Posted April 21, 2015 Remove OsxAptioFixDrv-64.efi inside your USB installation Thanks Allan, i tried this as well and it still boots to a black screen and gives the same message. Im not sure what i could be doing wrong here. Ive tried several variations of options..even different bootloaders from USB and the only one that works is the Mavericks installer USB that i make with [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url]. Quote Link to comment Share on other sites More sharing options...
Allan Posted April 21, 2015 Share Posted April 21, 2015 Choose the right EFI drivers for your Hack: http://www.insanelymac.com/forum/topic/282787-clover-v2-instructions/?p=1910955 Quote Link to comment Share on other sites More sharing options...
mindstate Posted April 23, 2015 Author Share Posted April 23, 2015 Hi Allan, Thanks for all your direction, i was able to successfully install 10.8.3 after may days of struggling with Mavericks. And i have the system booting with Chameleon. Only problem now is the kexts for the Intel HD Graphics that *should* work with this..do not. I installed them using Kext Wizard but when i check which kexts are loaded the IntelHDGraphics kext is not in the list. Any direction? Quote Link to comment Share on other sites More sharing options...
Allan Posted April 23, 2015 Share Posted April 23, 2015 What is your Intel HD Graphics model? Quote Link to comment Share on other sites More sharing options...
mindstate Posted April 23, 2015 Author Share Posted April 23, 2015 What is your Intel HD Graphics model? 1st Generation Intel HD Graphics i used the guide located here http://www.insanelymac.com/forum/topic/286092-guide-1st-generation-intel-hd-graphics-qeci/ and http://wiki.osx86project.org/wiki/index.php/HCL_10.8.3/Portables#EliteBook_8440p_.28Intel_HD_Graphics.29 Quote Link to comment Share on other sites More sharing options...
Allan Posted April 24, 2015 Share Posted April 24, 2015 Do you read the note about Video? Works - Supports Cl only QE not supported (10.8.5 kext) And the Note (Read First) inside the package: These Intel HD Graphics kexts are for OS X Mountain Lion 10.8.5. These kexts will allow you to enable only Core Image for your 2010 1st Generation Intel HD Graphics IGPU. Quote Link to comment Share on other sites More sharing options...
mindstate Posted April 24, 2015 Author Share Posted April 24, 2015 Yes.. according to that it works with 10.8.5 - 10.9 but according to this http://wiki.osx86project.org/wiki/index.php/HCL_10.8.3/Portables#EliteBook_8440p_.28Intel_HD_Graphics.29 the same Kexts can be used with 10.8.3 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.