Jump to content

Sigmatel 9223 Vendor Id 8384 Dev Id 7681 Is this right?

latexgurl

By latexgurl,
in Archive

 Share
107 posts in this topic

Recommended Posts

latexgurl
latexgurl
Posted
Posted

:hysterical::hysterical: OK

 

I have looked through all the forums and only found ways of getting the Sigmatel 9220 up and running in stereo and such by switching out .Kext files then with a Nebulous "should work for 922x sigmatel chipsets". Problem is on the Sigmatel 9223 Audio on the Intel i945gcz it just makes an otherwise great working system (xbench with onboard video and Pent D 820 at 89) not boot up and lock under Myzar 10.4.5 10.4.6.

 

I have also tried editing the Azalia kext with the Device ID and Vendor ID that I found in Windows XP Pro Device manager under Sound Simatel High Definition audio codec which is Vend Id 8384 and the Device ID 7681. Am I looking at the right device to get the proper Vend ID Dev ID? Dxdiag also confirms the ID's that I have found as V Id 8384 D id 7681.

 

My questions are

1. Is this the right ID numbers to insert into Azalia and otherwise?

2. Where do I put these ID numbers which .kext files are right for this?

 

I hear mention of doing this in AppleHd.kext and getting rid of others and such so I am a bit confused.

 

Any help would be greatly appreciated actually and some confirmation on the Device Id vendor id because when I look for other Sigmatel Chips thier Vendor Id is 8086 I think soooooooo.

 

If you can help me get this working I will just UMMMM I dont know send you a half naked picture of myself if that is any type of encouragement. Dont worry its from some modeling photos from a couple of years back.

 

 

SOOOOOO SOFT PORN/Modeling Photo FOR WORKING SIGMATEL 9223 Audio on my Intel I945GCZ. :graduated:

 

thanks ;-)

Ashe

Link to comment
Share on other sites
rogabean
rogabean
Posted
Posted

I've been hard at work on this for 3 days now latex. I've so far tried every method involving appleazaliaaudio and applehda kexts.

 

The best I have been able to do so far is get OS X to see the card and allow volume control of the output. But no sound is actually produced through any port with or without legacy support in the BIOS.

 

I'll keep you updated if I make any more progress, but so far nothing found in these forums has worked for our board. (my vend/devid is the same as yours).

 

Run ioreg -l | grep 27d8 and give me your results. A second tester as I work on this would be helpful. If I get some time tomorrow I will send you some kexts to try on your system (via a link in PM)

 

(that's a lower case L)

 

I'm going to try some of the older release kexts tomorrow and will let you know how that goes.

 

PS. did you have any trouble installing windows XP to this board? I couldn't get it to actually run any of the install disks EXCEPT the 64 bit edition. It hung on booting the CD on the 32 bit edition. No biggie though as the 64 bit version is running quite well on this board.

Link to comment
Share on other sites
latexgurl
latexgurl
Posted
  • Author
Posted

HEY YA Roga

 

Well the Grep went like this

 

| | | | "name" = "pci8086,27d8"

| | | | "IOName" = "pci8086,27d8"

| | | | "compatible" = <"pci8086,1110","pci8086,27d8","pciclass,040300"$

 

hope this is what you expected!!!

 

As for Windows XP Non 64bit version I do have it booting off of another HD a small Scsi drive and just switch the boot drive in the bios when I need to go to osx.

 

Well I will see what I can find out from this end also and hopefully we can solve the situation together. :-)

 

take care and Cheers

Link to comment
Share on other sites
jgb_jgb
jgb_jgb
Posted
Posted

hello i945gcz User's

Is it the d945gcz Intel BTX-board you have ? I bought an second-hand d945gcz/d945paw board just for getting into the x86mac world :o

I discovered that the BIOS-socket is empty and don't dare to buy a expensive 775 cpu (im unemployed at the moment) to find out that I have a bad motherboard. Do you have any chip in the BIOS-socket ?

Which pc-case do you recommend for the BTX-case ?

 

Is the x86mac working fully , except the audio ?

 

thanks for your time

Link to comment
Share on other sites
latexgurl
latexgurl
Posted
  • Author
Posted

Hey JGB

 

First for what I do know about the i945gcz board and my setup is that

Yes everything is working famously except for the Audio. At first the LAN Didnt show up but ROGABEAN below in the other post got me straight on that and its working well now.

SATA is working

Video is working Great

Peripherals are working Great

Firewire is working great synching my Ipod through it :-)

I have Ilife 2006 Working famously

Macromedia Studio 8 Working very well

Photoshop CS Humming along

VLC Mediaplayer ETC

So far the only problem I am having is getting logitech cameras to show up but thats a problem on regular macs also because Logitech Stopped developing for OSX soo

 

I will take a further look into the bios thing.

 

As for a case actually the least expensive BTX case I could find is made by Evercase

I just hacked up an ATX case along with my Dad(actually more him doing the mod than me you know dont want to muss my nails :D ) But the evercase is like 50$ or so.

 

So far though I have been very pleased with the machine and I am getting xbench scores of about 81 or so consistently with an old ide 80gb seagate as the boot drive.

 

Hope this all helps and have fun. Remember you can also instal a Celeron D 326 and have it work well and they are only $50 online if you cant scrape up enough for the Pentium D.

 

take care Ashe ;-)

Link to comment
Share on other sites
jgb_jgb
jgb_jgb
Posted
Posted

hi Latexgurl

 

thanks for your reply.

Youre right , i will go for the Cel cpu , but did you get the BTX variant, because of the cooler ?

I have looked at the coolers and its special for BTX boards I think.

Next time you look inside the chassi could you look if there is a bios-chip in the socket ?

 

thanks Josef

Link to comment
Share on other sites
rogabean
rogabean
Posted
Posted

latex. I must apologize I didn't get a chance to send you the files yesterday. I ended up having to work on my car instead of my os x box yesterday. I'll make every attempt to get them to you later today.

 

and yes that was the info i needed. thank you.

Link to comment
Share on other sites
rogabean
rogabean
Posted
Posted

Yes Munky I am most likely going to need some other testers as well, but i am going to hold sending out any files until I run a few more tests.

 

I've been pouring over the chipset's documents and specifications all day.

 

The only real difference between the 9220 and the 9223 is added support for optical spdif output... from what I can tell with my current driver the output is being piped to the optical output of my board... however I have no way to confirm or denyo this yet... so I'm going to work a little mre on this before i release any files.

 

I will keep you two up to date. I was going to send out files to latex today, but I would prefer to send a file i think has a chance of working before I have you start replacing kext files. In it's current form all that would be proved is the driver detects output hardware.

 

 

0x27d88086 (Intel HD Hub) and 0x76818384 (Sigmatel 9223) are the ID's present for your audio as well correct Munky?

Link to comment
Share on other sites
rogabean
rogabean
Posted
Posted

heh. I wasn't counting you out Munky. In it's current form I don't think I'm going to get the results I'm wanting. I just wanna see what happens on an identical board to mine to see if my current results are flawed.

 

By the way I *had* sound for about 10 minutes last night. 2 channel and no input but I had sound. A reboot killed that and I haven't been able to recreate what i did *yet*

Link to comment
Share on other sites
latexgurl
latexgurl
Posted
  • Author
Posted

HI Roga

 

Sorry havent chedked in the last few days because My brothers wife just had surgery for a brain tumor and I was helping take care of my nieces and cooking and such. You know keep the girl in the kitchen and helping the kids!!! Ok that was sexist but wait I am a girl sooo.

 

Anyway will try the files and seee. SO far in further testing though of the other subsystems everything is working absolutely fabulously!!!!

 

JGB as for the cooling issue I bought a thermaltake BTW cooler for about $30 Dollars and yes your going to need one cause both of the intel processors run hot.

 

Ok all off I gooo.

 

Ashley

Link to comment
Share on other sites
macintox
macintox
Posted
Posted
heh. I wasn't counting you out Munky. In it's current form I don't think I'm going to get the results I'm wanting. I just wanna see what happens on an identical board to mine to see if my current results are flawed.

 

By the way I *had* sound for about 10 minutes last night. 2 channel and no input but I had sound. A reboot killed that and I haven't been able to recreate what i did *yet*

 

Hey rogabean, are you working in a solution based on azalia or HDA (or both)?

When you "had sound for about 10 minutes", what kexts was loaded?

 

Thx

Link to comment
Share on other sites
rogabean
rogabean
Posted
Posted

as of now.. just using the AppleHDA... and only the AppleHDA.kext was loaded when I had sound. AppleAzaliaAudio was not present.

 

although I'm going to have to stop work on this for right now.... for personal reasons I'd rather not get into... I just won't have access to any machines for a while.

Link to comment
Share on other sites
skredii
skredii
Posted
Posted

Hello,

 

I got a Sigmatel 9223 too on a D945GNTLR intel motherboard.

 

Here is what I got when I run your command:

 

| | | | "name" = "pci8086,27d8"

| | | | "IOName" = "pci8086,27d8"

| | | | "compatible" = <"pci8086,303","pci8086,27d8","pciclass,040300">

 

Anyone has made any progress?

Link to comment
Share on other sites
yipwafe
yipwafe
Posted
Posted

Hi guys,

 

I also have sigmatel 9223 and I just managed to get a few minutes of sound out to "Line-In" (rather than green speaker out) before it stopped working, which I believe the kext might have crashed or gone mad.

 

Hope this info is useful and someone can push further:

 

1. Change all 2206496386 in Info.plist to 2206496385 (0x83847681)

2. Hexedit the real kext binary MacOS/AppleHDA, replace "82 76 84 83" to "81 76 84 83". <-- notice the byte ordering.

3. sudo kextload AppleHDA.ext

4. Play a MP3 file, you will have sound coming out of Line-In for a couple minutes.

 

 

Thanks

Link to comment
Share on other sites
skredii
skredii
Posted
Posted
hey yipwafe...

 

that might be the missing link I needed... once i get access to the machine I'm going to look at the changes you made and work them into mine.

 

Here's hoping.

 

Hey rogabean!

 

Could you post which kext are you using and what changes have you made?

 

Thanks.

Link to comment
Share on other sites
rogabean
rogabean
Posted
Posted

sure.. soon as I get a chance I'll release the kext I've been working on. It's a modified version of the 10.4.3 AppleHDA.kext at the moment.

 

right now I do not have access to my computers (posting from work) so I can't really do anything.

Link to comment
Share on other sites
yipwafe
yipwafe
Posted
Posted

Wow! I fixed the issue that it worked only a couple of minutes. Now it works all the time.

 

The problem seemed to be that I replaced strings of Sigmatel 9222 in the AppleHDA.kext with 9223. Instead, I should had replaced 9220 with 9223 because they have the pin layout according to their spec.

 

The issue still exists that sound is coming in the "blue line-in" plug rather than the "green speaker out". Well, at least it's working! ...

 

Here are the full steps:

 

1. Replace in /System/Library/Extensions/AppleHDA.kext/Contents/Info.plist all instances of 2206496384 with 2206496385

2. Use Hexedit, /System/Library/Extensions/AppleHDA.kext/Contents/MacOS/AppleHDA, replace all instances of "80 76 84 83" with "81 76 84 83"

3. sudo rm /System/Library/Extensions.kextcache

4. sudo kextcache -k /System/Library/Extensions

5. Reboot!

 

Open "System Preferences", then "Sound", you should see it all enabled!

Fire up iTune and enjoy!

Link to comment
Share on other sites
azpolo
azpolo
Posted
Posted

Thousands of people in the world we hoped like making the audio one functional of Sigmatel 9223. I say thanks from now on to you. I hope anxious

 

Warm Greetings

 

( With translator ES- EN)

Link to comment
Share on other sites
 Share
Go to topic listing
×
×
  • Create New...