Jump to content

Attansic L2 Driver


  • Please log in to reply
37 replies to this topic

#1
VampireMI2

VampireMI2

    InsanelyMac Protégé

  • Members
  • Pip
  • 18 posts
  • Gender:Male
  • Location:Thailand
I have ASUS P5GC-MX/1333 with Attansic L2 lan card onboard, everything work great only Ethernet, but I try modify info.plist in Attansic L1 kext but it's not work .
Have some kext or how to make it work?
Thank very much.

#2
reader02

reader02

    InsanelyMac Protégé

  • Members
  • PipPip
  • 63 posts
Now in the debugging, tx frame should not send。

Attached Files



#3
snetsplit

snetsplit

    InsanelyMac Protégé

  • Just Joined
  • Pip
  • 1 posts
Sweet I have that same motherboard and been trying to get the lan working for like the last week! Thank you very much!

#4
vampaz

vampaz

    InsanelyMac Protégé

  • Members
  • Pip
  • 6 posts
I'm getting the famous problem "Ethernet Adaptor (en1) has a self-assigned IP address and may not be able to connect."
Tried manual ip config and no network.

Is this working for you?

#5
reader02

reader02

    InsanelyMac Protégé

  • Members
  • PipPip
  • 63 posts
It can get the IP address , but can't work。

Attached Files



#6
reader02

reader02

    InsanelyMac Protégé

  • Members
  • PipPip
  • 63 posts
Ping test successfully, but can't work.

Attached Files



#7
reader02

reader02

    InsanelyMac Protégé

  • Members
  • PipPip
  • 63 posts
It's working on leopard 10.5.2 .

The latest version at here :
http://www.insanelym...p...d=1125350

Attached Files



#8
vampaz

vampaz

    InsanelyMac Protégé

  • Members
  • Pip
  • 6 posts

It's working for leopard 10.5.2 .


Working in ipc 10.5.6..

Thank you very much men, Kudos for you.
If you where in Lisbon i would pay 5 beers to you... ;)

But itunes craches, here is the crash report , maybe it helps.

Attached Files



#9
vampaz

vampaz

    InsanelyMac Protégé

  • Members
  • Pip
  • 6 posts
Sorry,it was a problem of my setup, working 100% now

#10
eberts

eberts

    InsanelyMac Geek

  • Members
  • PipPipPip
  • 138 posts
Thanks reader02! It works here but not after sleep. It reports everything is ok, cable connected but no ping to the router. I wonder if we could adjust anything in dsdt (I already injected the device, changed to built-in=yes). Where's the source code for it?

Thx a million ;)
eberts

#11
reader02

reader02

    InsanelyMac Protégé

  • Members
  • PipPip
  • 63 posts

It works here but not after sleep


see here:
http://www.insanelym...mp;#entry827504

#12
eberts

eberts

    InsanelyMac Geek

  • Members
  • PipPipPip
  • 138 posts
Thanks reader02, that's some kind of work around but it would be nice to have a fixed driver for hibernate. Maybe we can compare the code to the linux driver delivered by asus. Several lines in there can be spotted to put the device to sleep and waking it up again.

#13
BOBacious

BOBacious

    InsanelyMac Protégé

  • Just Joined
  • Pip
  • 3 posts

see here:
http://www.insanelym...mp;#entry827504



Works on my asus p5gc-mx, great effort on the author's part to get this chip compatible with OSX86. So far its great for surfing and internet stuff, but is really slow when filesharing and in a home network setting, about ten times slower, I had to go back to a the 8139. Hope this info helps with debugging.

cheers! :(

#14
Thacker

Thacker

    InsanelyMac Protégé

  • Members
  • Pip
  • 15 posts
Coool! Thank you, man!!!

#15
auqs10

auqs10

    InsanelyMac Geek

  • Members
  • PipPipPip
  • 123 posts
Hi reader02, works fine under Leo 10.5.6. Thank you

#16
the happy prince

the happy prince

    InsanelyMac Protégé

  • Members
  • Pip
  • 18 posts
  • Gender:Male
  • Location:India
thanx so much for this:) I have a P5GC-MX1333 & I ended up buy an Intex Realtek 1839 - this is a fake card. now gonna try to make the onboard Attansic L2 work with this:)

#17
jackrackam

jackrackam

    InsanelyMac Protégé

  • Just Joined
  • Pip
  • 1 posts

It's working on leopard 10.5.2 .

I give it a try but I get "Ethernet Adaptor (en0) has a self-assigned IP address and may not be able to connect."

Thanks for the effort but please :)

P5GC-MX 1333
leopard : 10.5.5 (ideneb)

After a few reboot and retry, :) it works :( however it seems that it does not like to sleep. When it wakes up I get "Ethernet Adaptor (en0) has a self-assigned IP address and may not be able to connect." again. kextunload + kextload seems to fix the problem (this solution was mentioned for ATL1E elsewhere).

Thanks a lot very good job.

#18
kaliti

kaliti

    InsanelyMac Protégé

  • Just Joined
  • Pip
  • 3 posts

It's working on leopard 10.5.2 .


Working on iDeneb v1.4, 10.5.6, Vanilla

Thanks!!! ;)

#19
reader02

reader02

    InsanelyMac Protégé

  • Members
  • PipPip
  • 63 posts
Here is new kext and source. It's fixed sleep issue.

Attached Files



#20
eberts

eberts

    InsanelyMac Geek

  • Members
  • PipPipPip
  • 138 posts

Works on my asus p5gc-mx, great effort on the author's part to get this chip compatible with OSX86. So far its great for surfing and internet stuff, but is really slow when filesharing and in a home network setting, about ten times slower, I had to go back to a the 8139. Hope this info helps with debugging.


Thanks a lot reader02! It works almost perfect :D
Sleep issues is gone - no problems anymore. I checked the debug kext: The upload seems to be very poor - 3.4GB estimated time = 60 min. The 8139 showed 7 min. for the same file.
It logs "no enough resource!!" every few packets.

Thanks again, great work reader02





0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users

© 2015 InsanelyMac  |   News  |   Forum  |   Downloads  |   OSx86 Wiki  |   Mac Netbook  |   PHP hosting by CatN  |   Designed by Ed Gain  |   Logo by irfan  |   Privacy Policy