OSx86 compatable?

[xequence]

Is this new computer I might be getting OSx86 compatable?

 

Though I am not sure if it is a sempron or an athlon... So, assume it is a sempron

 

Oh, and I plan to upgrade to 512mb ram

 

CPU: AMD Athlon 64 (3400+)

CPU Socket: Socket 754

Chipset: VIAR Chipset:

North bridge: VIA K8M800

- 800MHz HyperTransport interface

- Integrated UniChrome2 3D/2D graphics controller

South bridge: VIA VT8237:

- 16-bit "Ultra V-Link" host controller

- 533MB/sec. V-Link interface

Supports single channel (64-bit wide) memory interface

Two 184-pin DDR DIMM sockets

Supports up to 2GB using PC1600 (DDR200), PC2100 (DDR266), PC2700 (DDR333)

or PC3200 (DDR400) unbuffered DDR SDRAM DIMM

Memory: Supports single channel (64-bit wide) memory interface

Two 184-pin DDR DIMM sockets

Supports up to 2GB using PC1600 (DDR200), PC2100 (DDR266), PC2700 (DDR333)

or PC3200 (DDR400) unbuffered DDR SDRAM DIMM

BIOS: Award BIOS

4Mbit flash memory

Power Management: Wake-On-Events include:

- Wake-On-PS/2 Keyboard/Mouse

- Wake-On-USB Keyboard/Mouse

- Wake-On-Ring (external modem)

- Wake-On-LAN

- RTC timer to power-on the system

CPU Overheat Protection function monitors CPU temperature and fan during

system boot-up

Audio: AC97 2.2 extension compliant codec

S/PDIF-in/out compressed digital output

6-channel audio output via software

LAN: Fast ethernet LAN Phy supports 10/100Mbps

Fully compliant to IEEE 802.3 (10BASE-T) and 802.3u (100BASE-TX) standards

Graphics: Integrated UniChrome2 3D/2D graphics controller

Integrated S3 Graphics with 2D/3D acceleration

Supports 2D acceleration features

Supports 3D acceleration features

IDE: Supports ATA/33, ATA/66, ATA/100 and ATA/133 hard drives

UDMA Modes 3, 4, 5 and 6 Enhanced IDE (data transfer rate up to 133MB/sec.)

 

Serial ATA with RAID: Supports two SATA (Serial ATA) interfaces which are

compliant with SATA 1.0 specification (1.5Gbps interface)

Supports RAID 0, RAID 1 and JBOD

IEEE 1394: VIA VT6307 PCI 1394 integrated host controller

Supports two 100/200/400 Mb/sec ports

AGP: Supports AGP 8x up to 2133MB/sec. and AGP 4x up to 1066MB/sec.

bandwidth for 3D graphics applications

Rear Panel I/O Ports: 1 mini-DIN-6 PS/2 mouse port

1 mini-DIN-6 PS/2 keyboard port

1 DB-9 serial port

1 DB-25 parallel port

1 DB-15 VGA port

4 USB 2.0/1.1 ports

1 RJ45 LAN port

1 IEEE 1394 port

3 audio jacks: line-in, line-out and mic-in

2 connectors for 4 additional external USB 2.0/1.1 ports

1 connector for 1 external IEEE 1394 port

1 connector for 1 external serial port

1 front audio connector for external line-out and mic-in jacks

1 CD-in internal audio connector

1 S/PDIF-in/out connector

1 IrDA connector

2 Serial ATA connectors

2 IDE connectors

1 floppy connector

2 ATX power supply connectors

2 fan connectors

Expansion Slots: 1 AGP slot

3 PCI slots

1 CNR slot (optional)

PCB: 4 layers, microATX form factor

24.5 cm x 23 cm (9.65 in. x 9.06 in.)

 

Sorry if this isnt the right place to post this, but I havnt found another forum topic that would be better to post in.