jaigandhi5 Posted September 3, 2007 Share Posted September 3, 2007 Ok i just reinstalled osx 3rd time because i cant seem to figure out the problem after i do a fresh install the harddrive runs fast and smooth (boot osx in like 1min) but now all i did is follow the guide for broadcom, and callisto 003 and after that this is what happens: my specs: comapaq R4000 (laptop) x200 ( ) ata WD 100gb hdd amd 64 3500+ Link to comment Share on other sites More sharing options...
jaigandhi5 Posted September 3, 2007 Author Share Posted September 3, 2007 ok so... i went back to windows and restarted back in to osx and now the hdd is running FAST again...? went from 3.16 to 30.41! (xbench score) but im sure the problem will come back eventually... how do i fix it? Link to comment Share on other sites More sharing options...
gimpyviper Posted September 3, 2007 Share Posted September 3, 2007 ok so... i went back to windows and restarted back in to osx and now the hdd is running FAST again...? went from 3.16 to 30.41! (xbench score) but im sure the problem will come back eventually... how do i fix it? Which OSX86 Build you using Link to comment Share on other sites More sharing options...
jaigandhi5 Posted September 4, 2007 Author Share Posted September 4, 2007 uphuck's 10.4.9 for AMD Link to comment Share on other sites More sharing options...
gimpyviper Posted September 4, 2007 Share Posted September 4, 2007 uphuck's 10.4.9 for AMD Hmmmm ok I had bad drive performance on my Intel system until I installed the IOATA kext from 10.4.8 but supposedly that only works for Intel not AMD. Not sure if it's an issue with the x200 chipset? FYI on my Intel system i clock 55 for disk on my AMD I clock 85 (AMD has a Raptor X, it would be even higher but it's running through an SATA->IDE adapter.) Perhaps even when it's "working" it's not even working properly? Link to comment Share on other sites More sharing options...
jaigandhi5 Posted September 4, 2007 Author Share Posted September 4, 2007 well when i boot in to windows and reboot in to osx it runs super but when i just boot straight in to osx its slow... my scores are probably low because i think my hdd is 4200rpm (laptop) Link to comment Share on other sites More sharing options...
Hercon Posted June 9, 2008 Share Posted June 9, 2008 Hi I have the same laptop, Presario R4000, I have tried to install ToH and Kalyway, but I couldn't. Now I m downloading Uphuck 10.4.9_v1.4a, but also exist v1.3a and v1.2a. Can you tellme which version has used?... maybe an installaton tip? Thanks Link to comment Share on other sites More sharing options...
muhr Posted July 10, 2008 Share Posted July 10, 2008 Hi, I'm having the same problem (Maxtor SATA disk on a ASUS P5B DeLuxe WiFi AP, Intel q6600). This is my xBench performance: http://db.xbench.com/merge.xhtml?doc1=300622&doc2=260600 iATKOS v2.0i release. Have you found any solution to this yet? Link to comment Share on other sites More sharing options...
obijohn Posted July 11, 2008 Share Posted July 11, 2008 This is what you need: AppleIntelPIIXATA kext fully working... Link to comment Share on other sites More sharing options...
muhr Posted July 14, 2008 Share Posted July 14, 2008 Thank you! I just needed to get a little more used to the forum layout to find it... Working perfectly now =) Next step is to add dual head and dual graphics card support, but that's a whole other story... Thanx again =) Link to comment Share on other sites More sharing options...
Recommended Posts