Coobox Mac Posted December 18, 2005 Share Posted December 18, 2005 Hi Guys I'm an Italian Apple fan, I have a problem with my new PC, I want to try OS X X86 but it dosn't work. The problem is this: I've OS X X86 Tiger 10.4.1 when I boot from DVD , I can see the Darwin boot but when I press Enter appear a imege with the power button that say PLEASE REBOOT SYSTEM . Why ? My HW is : AMD Athlon Dual Core 3800 + (SSE - SSE2 -SSE3 ) MSI RS482M2-IL with ATI XPRESS X200 PS.: With VMWARE OS X X86 works fine PLEASE HELP ME pleaseeee sorry for my bad english Link to comment https://www.insanelymac.com/forum/topic/5932-help-amd-athlon-x2-3800-msi/ Share on other sites More sharing options...
Coobox Mac Posted December 18, 2005 Author Share Posted December 18, 2005 help Link to comment https://www.insanelymac.com/forum/topic/5932-help-amd-athlon-x2-3800-msi/#findComment-37353 Share on other sites More sharing options...
Gdfath3r Posted December 18, 2005 Share Posted December 18, 2005 (edited) Hi Guys I'm an Italian Apple fan, I have a problem with my new PC, I want to try OS X X86 but it dosn't work. The problem is this: I've OS X X86 Tiger 10.4.1 when I boot from DVD , I can see the Darwin boot but when I press Enter appear a imege with the power button that say PLEASE REBOOT SYSTEM . Why ? My HW is : AMD Athlon Dual Core 3800 + (SSE - SSE2 -SSE3 ) MSI RS482M2-IL with ATI XPRESS X200 PS.: With VMWARE OS X X86 works fine PLEASE HELP ME pleaseeee sorry for my bad english Probably you try to install on SATA drive. Try to install on IDE drive, also for start disable USB in BIOS. I hope you tried to install with proper patched disk. My opinion is based on this guide: Custom AMD [Athlon 64 3500+; MSI RS480] Method: Native using Deadmoo image, 'Simple and Accurate' to copy to partition 5 on second disk, and copied Chain0 to Win XP partition to boot. Using Maxxuss 0.4 SSE2/3 patch. * Note, the guide says this will not work on an extended partition, but it boots fine for me. Hardware: * AMD Athlon 64 3500 * 1GB memory * On board RealtekRTL 8169 Ethernet claims it loads correctly, but haven't tested. * On board AC97 (RealtekALC658C) won't work at all * On board Radeon X200 works OK, but only VESA 2. Can't change resolution as monitor won't support the defaulted refresh rate. * USB half works (see below) * Doesn't see my SATA (first) hard drive, but recognises the other partitions on my IDE drive. Comments: Needed to disable USB in the BIOS to get it to recognise the PS/2 keyboard and mouse, but the USB continued to work (for storage card, etc.) for a few re-boots, then mysteriously stopped working. Removed the ApplieIntel*.kext, though I'm not sure it was necessary. Also removed the TPM kext, as it was using 90% CPU Tried to install my Thomson Speedtouch USB ADSL modem, but it fails to load as it notices that the processor is not PowerPC (but why should it check?) Probably USB gives hard time to this guy and to you too..... Edited December 18, 2005 by Gdfath3r Link to comment https://www.insanelymac.com/forum/topic/5932-help-amd-athlon-x2-3800-msi/#findComment-37395 Share on other sites More sharing options...
Coobox Mac Posted December 19, 2005 Author Share Posted December 19, 2005 Thanks I've found a solution Now it works --> The problem was that my disk was set in CS mode ed not master. Now I've a new problem OS X is installed and perfectly works, but the installation wad dured 11Hs why ? NO DMA ? Link to comment https://www.insanelymac.com/forum/topic/5932-help-amd-athlon-x2-3800-msi/#findComment-37496 Share on other sites More sharing options...
Recommended Posts