HBP Posted May 31, 2023 Share Posted May 31, 2023 I have to choose between having access to 10 gig, or wifi, if I have DisableIoMapper checked in open core 9.2 then I get Wifi and it works correctly, but my Aquantia 10 gig will not acquire a DHCP address or link. if I have it unchecked then it will run the Aquantia 10 gig card, but the Broadcom will not enable though it is seen in the system information I will post any information requested after I redact it. Model Name: Mac Pro Model Identifier: MacPro7,1 Processor Name: 8-Core Intel Core i9 Processor Speed: 3.6 GHz Number of Processors: 1 Total Number of Cores: 8 L2 Cache (per Core): 256 KB L3 Cache: 16 MB Hyper-Threading Technology: Enabled Memory: 32 GB System Firmware Version: 1968.100.17.0.0 OS Loader Version: 577~170 PCI and Network info: pci14e4,43a0: Type: Other Network Controller Driver Installed: Yes MSI: Yes Bus: PCI Slot: 0,0@6,0,0 Vendor ID: 0x14e4 Device ID: 0x43a0 Subsystem Vendor ID: 0x106b Subsystem ID: 0x0117 Revision ID: 0x0003 Link Width: x1 Link Speed: 2.5 GT/s Wi-Fi: Type: AirPort Hardware: AirPort BSD Device Name: en3 IPv4: Configuration Method: DHCP IPv6: Configuration Method: Automatic Ethernet: MAC Address: b8:09:8a:45:56:26 Media Options: Media Subtype: Auto Select Proxies: Exceptions List: *.local, 169.254/16 FTP Passive Mode: Yes Service Order: 3 Aquantia AQC107-B0: Name: ethernet Type: Ethernet Controller Driver Installed: Yes MSI: Yes Bus: PCI Slot: 0,0@4,0,0 Vendor ID: 0x1d6a Device ID: 0x07b1 Subsystem Vendor ID: 0x1d6a Subsystem ID: 0x0001 Revision ID: 0x0002 Link Width: x4 Link Speed: 8.0 GT/s Ethernet 3: Type: Ethernet Hardware: Ethernet BSD Device Name: en2 IPv4 Addresses: redacted IPv4: Additional Routes: Destination Address: redacted Subnet Mask: 255.255.255.255 Destination Address: redacted Subnet Mask: 255.255.0.0 Addresses: redacted ARP Resolved Hardware Address: 00:1b:21:redacted ARP Resolved IP Address: redacted Configuration Method: DHCP Confirmed Interface Name: en2 Interface Name: en2 Network Signature: IPv4.Router= Router: Subnet Masks: 255.255.255.0 IPv6: Configuration Method: Automatic DNS: Domain Name: redacted Server Addresses: redacted DHCP Server Responses: Domain Name: redacted Domain Name Servers: redacted Lease Duration (seconds): 0 DHCP Message Type: 0x05 Routers: redacted Server Identifier: redacted Subnet Mask: 255.255.255.0 Ethernet: MAC Address: 00:17:b6:00:85:56 Media Options: Full Duplex Media Subtype: 10Gbase-T Proxies: Exceptions List: *.local, 169.254/16 FTP Passive Mode: Yes Service Order: 2 Link to comment https://www.insanelymac.com/forum/topic/356847-marvell-aquantia-10-gb-ethernet-and-bcm4360-ac1200-fenvi-not-compatible/ Share on other sites More sharing options...
miliuco Posted June 2, 2023 Share Posted June 2, 2023 (edited) @HBP Try this settings by default, maybe the Fenvi fails with them: VT-d enabled in BIOS Kernel >> ForceAquantiaEthernet enabled in config.plist Kernel >> DisableIoMapper disabled in config.plist Kernel >> DisableIoMapperMapping enabled in config.plist On some systems you need to drop the original DMAR ACPI table and replace it by a modified one without Reserved Memory Region block/s. This is a more complicated task but fixes the Ethernet and Wifi issue.https://github.com/acidanthera/OpenCorePkg/commit/24414555f2c07e06a3674ec7a2aa1ce4860bbcc7#commitcomment-70530145 Additional info on Aquantia-macOS-Patches by @Casey_S.J. Edited June 2, 2023 by miliuco 1 Link to comment https://www.insanelymac.com/forum/topic/356847-marvell-aquantia-10-gb-ethernet-and-bcm4360-ac1200-fenvi-not-compatible/#findComment-2805464 Share on other sites More sharing options...
HBP Posted June 5, 2023 Author Share Posted June 5, 2023 On 6/2/2023 at 12:18 PM, miliuco said: @HBP Try this settings by default, maybe the Fenvi fails with them: VT-d enabled in BIOS Kernel >> ForceAquantiaEthernet enabled in config.plist Kernel >> DisableIoMapper disabled in config.plist Kernel >> DisableIoMapperMapping enabled in config.plist On some systems you need to drop the original DMAR ACPI table and replace it by a modified one without Reserved Memory Region block/s. This is a more complicated task but fixes the Ethernet and Wifi issue.https://github.com/acidanthera/OpenCorePkg/commit/24414555f2c07e06a3674ec7a2aa1ce4860bbcc7#commitcomment-70530145 Additional info on Aquantia-macOS-Patches by @Casey_S.J. You are a Rock Star!!! I have been searching for this for almost a year now, which is why I finely just created a new Post. now if only I could resolve the Watchdogd not liking my Saphire 5700 XT I would be rockin!!! 1 Link to comment https://www.insanelymac.com/forum/topic/356847-marvell-aquantia-10-gb-ethernet-and-bcm4360-ac1200-fenvi-not-compatible/#findComment-2805595 Share on other sites More sharing options...
miliuco Posted June 6, 2023 Share Posted June 6, 2023 @HBP Glad to read you. Did you need to drop DMAR table or it wasn’t required? Open a new thread for watchdog. Link to comment https://www.insanelymac.com/forum/topic/356847-marvell-aquantia-10-gb-ethernet-and-bcm4360-ac1200-fenvi-not-compatible/#findComment-2805662 Share on other sites More sharing options...
Shikumo Posted June 21, 2023 Share Posted June 21, 2023 (edited) Oops. Wrong thread. Edited June 21, 2023 by Shikumo Wrong thread. 1 Link to comment https://www.insanelymac.com/forum/topic/356847-marvell-aquantia-10-gb-ethernet-and-bcm4360-ac1200-fenvi-not-compatible/#findComment-2806946 Share on other sites More sharing options...
Recommended Posts