Jump to content

Attempting ML on Samsung NP550 Series 5


78 posts in this topic

Recommended Posts

Hello

 

Trying the install on to A Samsung NP550...

 

Install finishes fine but then hit the error in the image attachment when reboot.

 

I boot using the USB and use the switches:

 

GraphicsEnabler=No -v

 

help needed - thanks,

 

Ten minutes later...

 

Also just tried AHCIPortInjector.kext from here.

 

and the recommended boot up:

 

-f -v GraphicsEnabler=No npci=0x2000

 

might be getting further ?? seeing this now:

laptop_ids.txt

post-15126-0-31741400-1346247032_thumb.jpg

post-15126-0-18504300-1346248307_thumb.jpg

Link to comment
Share on other sites

Thanks I'll keep looking... know of any decent ones ?

 

I changed in the mean time the /Extra/smbios.plist to use MacBookPro8,2 MacBookPro9,2 since using Ivy Bridge CPU and gets perhaps a bit further... then again may be I am being too optimistic....

post-15126-0-96803400-1346250421_thumb.jpg

Link to comment
Share on other sites

Thanks again....

 

The Ethernet adapter I thought would be first of all since wireless isn't appearing under networking however have u seen anything like this before where the Adapter is shown as connected, I have Manually configured however no networking is possible.

 

Similarly if I left it to get an address assigned via DHCP it would only get a 169.172 private address assigned...

 

 

As for the boot loader I tried install Chimera (both from [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] as well as dedicated installer) however the disk appears to be untouched afterwards

 

i.e.

 

No /Extra folder no contents is created...

 

v. strange.

post-15126-0-21855500-1346256828_thumb.png

Link to comment
Share on other sites

No luck getting the ethernet working....

 

Most confused since what I can see it should be working. lspci output at the top of thread shows:

 

03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06)

 

Similarly System Info out put shows that the device is loaded.... the Ethenet is configurable in Network preferences however no pinging or lookups working. Also Network Utility shows no sent packages nor any errors.

 

Seriously out of ideas : (

post-15126-0-32325400-1346270256_thumb.png

Link to comment
Share on other sites

The IO80211Family kext installed is version 5.0. The AirAtheros40 kext within does not have an Info.plist - see screenshot Screen Shot 2012-08-30 at 6.13.19 PM

 

I put earlier version 4.2 in place (fixed permisions) and made the edit then rebooted see screenshot Screen Shot 2012-08-30 at 6.09.30 PM.

 

No wireless... yet....

post-15126-0-95196700-1346336032_thumb.png

post-15126-0-26258700-1346336213_thumb.png

Link to comment
Share on other sites

Nope no wireless.

 

Would "Safe Boot" be causing this ?

 

No IO80211Family nor AppleAtheros40 kexts appear to be loaded....

 

sudo dmesg shows

 

SAFE BOOT DETECTED - only vaild OSBundleRequired kexts will be loaded.

 

will try booting using:

 

-v GraphicsEnabler=No PciRootUID=0 npci=0x3000

Link to comment
Share on other sites

yes I have repaired permssions and rebuilt kext cache using Champlist.

 

rebooting without "-x" option leaves me on stuck (see screenshot)

 

Is this error due there being no suppported power management ?

 

BTW I have already done the 10.8.1 update.

post-15126-0-39288800-1346342362_thumb.jpg

Link to comment
Share on other sites

ok, backup this kext AppleIntelCPUPowerManegement.kext and delete from S/L/E repairPermissions and reboot

 

Found this somewhere. Use with caution.

MBP10,1 is the Retina while 9,1 and 9,2 is normal macbookpros with IVY BRIDGE

Attached Files

Link to comment
Share on other sites

Here is an ls -la:

 

 

utching:~ David$ cd /Volumes/MOUNTAINLION/Extra/Extensions/

kutching:Extensions David$ ls -la

total 0

drwxr-xr-x@ 12 David staff 408 Aug 29 15:33 .

drwxr-xr-x@ 7 David staff 238 Aug 30 2012 ..

drwxr-xr--@ 3 David staff 102 Aug 29 15:33 AHCIPortInjector.kext

drwxr-xr-x@ 3 David staff 102 Sep 4 2011 AHCI_3rdParty_SATA.kext

drwxr-xr-x@ 3 David staff 102 Aug 24 2011 AppleACPIPS2Nub.kext

drwxr-xr-x@ 3 David staff 102 May 21 22:58 AppleACPIPlatform.kext

drwxr-xr-x@ 3 David staff 102 Aug 24 2011 ApplePS2Controller.kext

drwxr-xr-x@ 3 David staff 102 Oct 30 2009 EvOreboot.kext

drwxr-xr-x@ 3 David staff 102 May 9 17:20 FakeSMC.kext

drwxr-xr-x@ 3 David staff 102 Jun 18 2011 IONetworkingFamily.kext

drwxr-xr-x@ 3 David staff 102 Jul 17 2009 JMicron36xATA.kext

drwxr-xr-x@ 3 David staff 102 Aug 22 2009 NullCPUPowerManagement.kext

 

If u need the actual kext then I'll drop them by email.

Link to comment
Share on other sites

why you have all this kexts? you only need FakeSMC.kext and NullCpuPowermanegement.kext installed in System/Library/Extensions

 

for it you have all this problems, and who is your SMBIOS.plist and org.chameleon.boot.plist ????? DROP in more reply options when you post, you can attach files here

Link to comment
Share on other sites

I attached the smbios.plist (as smbios.txt) a few posts back along with the org.chameleon.plist (as .txt) - let me chop some kexts leaving just the two mentioned in /E/E...

 

ok seems as though I need more than just these two kexts since rebooting I have no lost control of KB and touchpad

Link to comment
Share on other sites

yes more two kexts only, ApplePS2Nub.kext and ApplePS2Controller.kext intall in System/Library/Extensions and please put your SMBIOS and org.chameleon.boot.plist in Extra!!!!!!

 

this is for keyboard and trackpad

Link to comment
Share on other sites

 Share

×
×
  • Create New...