bbchucks Posted June 18, 2010 Share Posted June 18, 2010 was on 10.6.3, updated to 10.6.4 and no video, goes powersave mode, black screen...can only VNC into the machine. anyone have ideas? edited ATI4800Controller kext to enter my deviceid. my software info shows: ATI Radeon 4870 Series: Name: ATY,Motmot Type: display Driver Installed: Yes Bus: PCI Slot: Slot-1 Vendor ID: 0x1002 Device ID: 0x9440 Subsystem Vendor ID: 0x174b Subsystem ID: 0xe114 Revision ID: 0x0000 Link Width: x16 Link Speed: 2.5 GT/s ATI Radeon 4870 Series: Chipset Model: ATI Radeon 4870 Series Type: GPU Bus: PCIe Slot: Slot-1 PCIe Lane Width: x16 VRAM (Total): 1024 MB Vendor: ATI (0x1002) Device ID: 0x9440 Revision ID: 0x0000 ROM Revision: 113-B7710C-176 EFI Driver Version: 01.00.318 Displays: Display Connector: Display Connector: Link to comment https://www.insanelymac.com/forum/topic/221575-ati-4870-with-1064/ Share on other sites More sharing options...
bbchucks Posted June 18, 2010 Author Share Posted June 18, 2010 ATI 4870 fixed!!! on 10.6.4.. looks like i'm stuck using the old 10.6.2 ATI files.. had to copy the following three ATI4800controller, ATIFramebuffer and ATISupport (all 3 are on 1.6.6 version) to S/L/E. also needed LegacyATI4800Controller.Kext in /Extra/Stored_Kexts Link to comment https://www.insanelymac.com/forum/topic/221575-ati-4870-with-1064/#findComment-1492696 Share on other sites More sharing options...
amardeep Posted June 19, 2010 Share Posted June 19, 2010 Any chance you can upload those kexts to a file and maybe expand a little on what you did? I've tried searching around for those files and adding them to the right directories, but am still only getting about 30 seconds of video before the display shuts off. Link to comment https://www.insanelymac.com/forum/topic/221575-ati-4870-with-1064/#findComment-1493468 Share on other sites More sharing options...
N00bishMacer Posted June 19, 2010 Share Posted June 19, 2010 I run both EvoEnabler.kext, and LegacyATI4800Controller.kext with Graphics Enabler set to Yes and lm using the vanilla 10.6.4 updated files no problems at all. Link to comment https://www.insanelymac.com/forum/topic/221575-ati-4870-with-1064/#findComment-1493489 Share on other sites More sharing options...
amardeep Posted June 19, 2010 Share Posted June 19, 2010 I run both EvoEnabler.kext, and LegacyATI4800Controller.kext with Graphics Enabler set to Yes and lm using the vanilla 10.6.4 updated files no problems at all. Updated to those kexts, has been running for about 10 minutes now without display problems. Thanks (knock on wood). My profiler says that I'm running a 4890 though, when the card is a 4870. Any idea how to fix this? Some .plist I need to update or something? Hm, I'm getting a bunch of these white lines through everything running. Is there a fix for this? http://i50.tinypic.com/1z1gpj5.jpg Link to comment https://www.insanelymac.com/forum/topic/221575-ati-4870-with-1064/#findComment-1493531 Share on other sites More sharing options...
N00bishMacer Posted June 19, 2010 Share Posted June 19, 2010 Attached are my 2 files: They will display 4870, just replace yours with mine and rebuild your caches with Kext Utility and reboot. ATIextrafiles.zip Link to comment https://www.insanelymac.com/forum/topic/221575-ati-4870-with-1064/#findComment-1493786 Share on other sites More sharing options...
water_cooling_man Posted April 6, 2011 Share Posted April 6, 2011 Hey guys, It has been a long time since I've done anything to my 10.6.4 Snow Leopard setup and I've forgotten a lot of the locations and commands for critical items, etc. I'm switching over to a 4870 from the 9400GT that has served me well since I built this rig a while back. Can you guys remind me which folder these ATIextra files go in. Is it /System/Library/Extensions? There's no EVOenabler.kext or LegacyATI4800Controller.kext in there at this point. Thanks! Link to comment https://www.insanelymac.com/forum/topic/221575-ati-4870-with-1064/#findComment-1666762 Share on other sites More sharing options...
Recommended Posts