jldajo Posted September 11, 2008 Share Posted September 11, 2008 hi.... greetings... JL here, hoping you can help me out. i've downloaded ideneb v1.1 - 10.5.4 from mininova... my specs are: - amd athlon 4400 dual core x2 64 - ide 40gig hard disk - 64mb nvidia graphics card first, i installed it without customizing, and i got an infinite reboot after the darwin bootup. then, i erased again, then installed selecting all options in the customize installation. it now goes to the gray apple screen, but would end up with the error that i should press my power button, pc needs to shut down. maybe you can help me out, on which options i should pick. just in case, you can see the ideneb in mininova. and also, what else i should've done. thank you so much for your help in advance. hope you can help me with my ideneb installation... sorry, here are my mother board specs according to MSI http://www.msicomputer.com/product/p_spec....model=K9N6SGM-V CPU • Supports 64-bit AMD® Sempron, Athlon™ 64 /Athlon 64 X2 processor (Socket AM2) • Supports Athlon 64 CPU: 3500+, 3800+ • Supports Athlon 64 X2 CPU: 3800+, 4000+, 4200, 4400+, 4600+, 4800+, 5000+, 5200+ Chipset NVIDIA ® GeForce 6100 nForce 405 (MCP61S) Chipset - HyperTransport connection to AMD AM2 Athlon64 processor - 8 or 16 bit control/address/data transfer both directions - 1GHz "Double Data Rate" operation both direction - Supports one PCI-E x8 *on x16 slot) and one PCI-E x1 slots - GeForce 6100 Grphic integrated shared up to 128MB - Supports SATAII controllers for two drives - Supports single channel Ultra DMA 66/100/133 master mode EIDE controller - Supports Hi-Speed (USB2.0) controller 480 mbsec transfer rate up to 8 ports Main Memory • Supports dual channel DDR2 400/533/667/800, using four 240-pin DDR2 DIMMs. • Supports the memory size up to 2GB • Supports 1.8v DDR2 SDRAM DIMM Due to the High Performance Memory design, motherboards or system configurations may or may not operate smoothly at the JEDEC (Joint Electron Device Engineering Council) standard settings (BIOS Default on the motherboard) such as DDR2 voltage, memory speeds and memory timing. Please confirm and adjust your memory setting in the BIOS accordingly for better system stability. Example: Kingston HyperX DDR2-800 PC-6400 operates at 2.0V, 4-4-4-12. For more information about specification of high performance memory modules, please check with your Memory Manufactures for more details. Slots • One PCI Express X16 slot (Run at x8 mode) (Due to the specification of the chipset, ATI X8xx, X7xx, X5xx, and X3xx series graphic card will not be supported.) • One PCI Express X1 slots • Two 32-bit Master 3.3v/5v PCI Bus slots On-Board IDE/SATA • An IDE controller on the NVIDIA® GeForce 6100 nForce 405 chipset provides IDE HDD/CD-ROM with PIO, Bus Master and Ultra DMA133/100/66 operation modes. - Can connect up to 2 IDE devices • NVIDIA® GeForce 6100 nForce 405 supports 2 SATA II ports - Transfer rate is up to 300MB/s - Supports RAID 0, 1 BIOS • The mainboard BIOS provides "Plug & Play" BIOS which detects the peripheral devices and expansion cards of the board automatically. • The mainboard provides a Desktop Management Interface (DMI) function which records your mainboard specifications. Audio • 7.1 channel audio codec RealTek ALC883 - Flexible 8-channel audio with jack sensing - Compliant with Azalia 1.0 spec LAN • Realtek 8201CL - Supports 10Mb/s or 100Mb/s On-Board Peripherals - 1 floppy port supports 1 FDD with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes - 1 VGA port - 1 parallel port supporting SPP/EPP/ECP mode - 8 USB2.0 ports (rear x 4 / front x 4 ) - 1 Audio jack (5-in-1), coaxial/fiber SPDIF out - 1 RJ-45 LAN Jack - 1 IDE ports support 2 IDE devices - 2 serial ATA ports - 1 serial port Dimension 9.61 in (L) x 8.2 in(W) Micro-ATX Form Factor Mounting 6 mounting holes Link to comment Share on other sites More sharing options...
super_engine Posted September 11, 2008 Share Posted September 11, 2008 during the installation you must select ONLY ONE kernel and ONLY the NVidia Chipset and AMD Patching For AMD systems you can choice ONLY MODBIN kernel (the best for AMD) Don't select GRAPHICS and AUDIO, install they AFTER At the reboot press F8 and type -v and ENTER. So you ca see what happens during the reboot. Good Luck Link to comment Share on other sites More sharing options...
Recommended Posts