TheNaraku Posted May 8, 2008 Share Posted May 8, 2008 i have a error with V3 and V2 (however V2 just reboots the -f and -x dose nothing at all)i have posted in a seperete forum here. but it was a very large forum. and i'd like to make sure its seen. i have a reboot cycle after like 3 seconds after starting the darwin bootloader it will load the Drivers (Extentions) it will load that same file two more times.. then reboot i've changed all bios options revelvent i really dont think the burn was bad i burnt it at half speed. and it compleated successfully i've also passed every boot option documented no diffrencence other than -x and -f will load all ktext's my specs: P4 478 3.06Ghz SSE2 1GB DDR ECS 848P-A ( Intel 848P Chipset ICH5) Sapphire HD 2600 PRO (AGP) the Hard Drive that that is intended for OSX is the Secondary SATA drive (im really unsure what SATA Controller is but it should be relevent as im not even to the point where it deals with harddrives) also there is some message that flashes very very fast i've tried to pause the system with the pause key but its no use its just to fast to catch. im not positive what it says at one time i think i saw EFI at the begining but im not sure i also thought i saw the word enhanced in there Please eddie can you help me.. for some reason (i dont know why because its not even to the point of changing disks/partition but appearently it has removed my vista bootloader or the entire partition itself i dont know for sure i just knows it fails to boot now..) all my hardware should be compatible. i hope there can be a simple patch or something.. that 3.4GB iso is killer takes me a long while to download EDIT: i have found that the message that flashes right before the reboot says EFI enhanced bootloader build: ToH then something about SMBIOS Table Found at xxxxx on another note i've read that my motherboard is fully supported by OSX however it was with a different processor (2.66Ghz) eddie11c, do you know if the northwood 3.06Ghz is supported in leopard and your release Thanks for any help Link to comment https://www.insanelymac.com/forum/topic/103815-leo4all-v2-and-v3-bootloader-problems/ Share on other sites More sharing options...
ka911 Posted May 8, 2008 Share Posted May 8, 2008 try to boot with -x -v command to see your errors. Link to comment https://www.insanelymac.com/forum/topic/103815-leo4all-v2-and-v3-bootloader-problems/#findComment-739648 Share on other sites More sharing options...
eddie11c Posted May 8, 2008 Share Posted May 8, 2008 Sounds like your stuck in the reboot loop that many P4 users have, I have a working version to address this, but not yet ready to release. There will be some other new options with this update so I would like to get them all hashed out first. Link to comment https://www.insanelymac.com/forum/topic/103815-leo4all-v2-and-v3-bootloader-problems/#findComment-740096 Share on other sites More sharing options...
TheNaraku Posted May 9, 2008 Author Share Posted May 9, 2008 Thanks for the insight eddie11c, do you know if it will be possable to make this in a simple iso patcher so i wont have to download the entire iso agian. i will understand if its not possable for you to do this. its just that 4GB dvd takes me nearly 3 days to download, and i've seen a few projects (other open source type project) use ISO patchers that juts edit the certan files in the iso file a much smaller patching system than re downloading the whole ISO if you'd like my direct email pm me here after i get Leo4all running i'd gladly (Beta Test) for you and report any issues and bugs. as im no stranger to OSX and Unix im quite proficent in them both Link to comment https://www.insanelymac.com/forum/topic/103815-leo4all-v2-and-v3-bootloader-problems/#findComment-740567 Share on other sites More sharing options...
eddie11c Posted May 9, 2008 Share Posted May 9, 2008 As of right now I do not know if it can be one via a simple patch. I have added some options, removed some. Once I finish everything I will see if a patch is possible. Link to comment https://www.insanelymac.com/forum/topic/103815-leo4all-v2-and-v3-bootloader-problems/#findComment-740782 Share on other sites More sharing options...
(MoC) Posted June 7, 2008 Share Posted June 7, 2008 As of right now I do not know if it can be one via a simple patch. I have added some options, removed some. Once I finish everything I will see if a patch is possible. Having the same issue. Release a small PPF patch for us P4 users though Or you can tell us how to manually do it ^^ Link to comment https://www.insanelymac.com/forum/topic/103815-leo4all-v2-and-v3-bootloader-problems/#findComment-774973 Share on other sites More sharing options...
Recommended Posts