OnePlane Posted March 6, 2008 Share Posted March 6, 2008 I installed with Kalyway 10.5.1, ran all the stuff, only had HDA audio for realtek and the kernel things on. Installation went fine and error-free. Reboot without dvd, and bummer. No go. Goes all the way up to the bootloader, booting without anything doesn't work. With (or without) -v it quickly displays some text and then video dies and the computer reboots. Don't know about any other commands. Specs: North: VIA P4M900 South: VIA VT8237S Audio: Realtek ALC662 (Azalia) LAN: Atheros AR8012BO1A (Yes, that IS ethernet and not wifi) SATA and IDE are accounted for by those VIA chips. Asus P5VD2-VM SE with Intel Pentium E2160, 1Gb DDR2, DVD drive as slave with Seagate ATA drive on master on the only ATA connector inside. Also has SATA but I don't have a SATA lying around atm. So, what's next? Any clues? I can provide more information when needed. Link to comment https://www.insanelymac.com/forum/topic/92068-no-go-after-installation-kalyway-1051/ Share on other sites More sharing options...
OnePlane Posted March 6, 2008 Author Share Posted March 6, 2008 Hit me. Fixed by (of course) reading the kalyway thread: NX was disabeld and should have been on. What's not doing what it's supposed to do: - Audio (Realtek ALC662) Not working, not recognized. - LAN (Atheros AR8012-B01A) Not working, not recognized. - SATA not working - Video is VESA. (P4M900's Chrome9) My mobo: P5VD2-VM SE CPU Intel Pentium Dualcore E2160 (1.8Ghz) Will buy a 8400GS 256MB PCIe and see if it works.. They're cheap (39 eur) and seem to support QE & CI with a patch. Link to comment https://www.insanelymac.com/forum/topic/92068-no-go-after-installation-kalyway-1051/#findComment-657095 Share on other sites More sharing options...
Macbandhu Posted March 6, 2008 Share Posted March 6, 2008 Hi Frnd I also have the same problem. I used Kaliway Disc and installation went very fine. But when i restart it after pullin out the DVD then it shows the daarwin bootloader and after i enter or in any other startup mode the same prob is there. that is the video dies .. How can i disable/enable NX? Plz Answer Thnx in Advance... Link to comment https://www.insanelymac.com/forum/topic/92068-no-go-after-installation-kalyway-1051/#findComment-657107 Share on other sites More sharing options...
OnePlane Posted March 7, 2008 Author Share Posted March 7, 2008 Change the settings in your BIOS. Read the manual of your motherboard for advice on how to do that. :censored2: Link to comment https://www.insanelymac.com/forum/topic/92068-no-go-after-installation-kalyway-1051/#findComment-657509 Share on other sites More sharing options...
OnePlane Posted March 10, 2008 Author Share Posted March 10, 2008 I got my setup working Everything, except for audio and video. Video will never work (chrome9) so that's getting replaced by the 8400GS soon. SATA works by adding the DEV_ID for 5372 VIA chip into the VIAATA kext. Audio needs a patch (ALC662 can work with the ALC882 driver??) Link to comment https://www.insanelymac.com/forum/topic/92068-no-go-after-installation-kalyway-1051/#findComment-660880 Share on other sites More sharing options...
Recommended Posts