Jump to content

Can't boot after installing Toh


HELLOOO
 Share

3 posts in this topic

Recommended Posts

My Vostro 1400 with:

 

Intel® Core 2 Duo CPU T7100@1.80GHz,1795 MHz x86, x86-64, MMX, SSE, SSE2, SSE3, SSSE3 | 1GX2 | Seagate ST9160821AS SATA 160GB

North Bridge: Intel Crestline-PM PM965 | South Bridge: Intel 82801HBM ICH8-DO

PCI Express 1.0 x16: nVIDIA GeForce 8400M GS (Dell) 128MB GDDR3 | SigmaTel STAC9228X @ Intel 82801HBM ICH8M - High Definition Audio Controller [b-0] PCI

Broadcom NetLink ™ Fast Ethernet | Intel® PRO/Wireless 3945ABG Network Connection

OS: Vista Ultimate SP1 V275 | BIOS: Phoenix A01 07/Oct/2007

 

What i did:

1.Eraze HD with Toh _x86_9a581_rc2 installation disc;

 

2.My HD allocation:

 

C: 101GB installed Vista, Pri, active;

D:20GB for Leopard,Lable: ILA,Pri;

E: 32GB NTFS,Blank,Pri;

 

3.successfully installed Toh _x86_9a581_rc2 and run /usr/misc/script.sh ILA in termination;

However,

 

4.Reboot and the following prompts:

 

----------System Prompt under 4 languages------------------------------------------

 

panic(cpu 0 caller oxoo1A7BED):Kernel trap at 0x001976bc type 14=page fault registers:

CR0:0x8001003b, CR2: 0x2e3b8000, CR3: 0x00efd000, CR4: 0x00000660

EAX: 0xffff4000, EBX:0x2e3b8000, ECX:0x00000400, EDX: 0x00001000

CR2:0x2e3b8000, EBP:0x2804beb8, ESI:0x00801000, EDI: 0x2e3b8000

EFL: 0x00010206, EIP: 0x001976bc, CS: 0x00000008, DS: 0x28040010

 

Error Code: 0x00000002

 

Debugger called: <panic>

 

Backtrace, Format-frame:Return Address(4 potential args on stack)

0x2804bca8:0x12b0e1(0x4555b4 0x2804bcdc ox133238 0x0)

0x2804bcf8:0x1a7bed(0x45e568 0x1976bc 0xe 0x45dd24)

0x2804bdd8:0x19e517(0x2804bdf0 0x121bc30 0x2804beb8 0x1976bc)

0x2804bde8:0x1976bc(0xe 0x1210048 0x10 0x10)

0x2804beb8:0x1af561(0x1 0x2804bf14 0x2000 0x0)

0x2804bf38:0x1aa3c5(0xffff0000 0x50febc 0x0 0x51bf80)

0x2804bf88:0x181938(0x3a28c10 0x1 0x0 0x5350c0)

0x2804bfa8:0x137bf5(0x0 0x0 0x13...(Here covered by 4 languages.Can't be seen))

0x2804bfc8:0x19e2ec(0x0 0xfffff5...(Here covered by 4 languages.Can't be seen))

 

Backtrace terminated-invalid frame.....(Here covered by 4 languages.Can't be seen)

BSD process name corresponding to....(Here covered by 4 languages.Can't be seen)

 

Mac OS Version

Net yet set

 

Kernel version

Darwin Kernel Version 9.0.0 Tue Oct.....

----------------------------------------------------------------------------------------------

Guys,

 

What should i do?How can i boot OSX in my PC? Thanks in advance!

Link to comment
Share on other sites

Im getting the same thing. I have not found a solution yet.

 

hi there.... a little experiance to share, might be helpful

 

make sure followings..

 

1. you activate leopard drive.

2. leopard drive is primary and FAT32 format, (i.e. Pri, Act, LBA)

3. Mac OS X Journailed FS

 

Now, install "MacOS 10.4.XX jas" if you have one without any patch only base system and than upgrade to TOH 10.5 as this worked for mine.

 

or

 

you can goolge for 1954_postpatch.sh / "brazilmac" patch but seems tricky and i was lost 4 times.

 

so good luck

Link to comment
Share on other sites

 Share

×
×
  • Create New...