Trying to get Ati and Sound to work properlly.

[yoannez]

Hi All

 

I have an Ati 9600 Mobility in a IBM T42.

That is currently running in 1280x1024x32 QE CI enabled, with some graphical artifacts...

Currently the card is identifyed as beeing a PCI card and this brings a doubt is it supposed to be like this?

 

Type: VGA-Compatible Controller

Bus: PCI

VRAM (Total): 128 MB

Vendor: ATI (0x1002)

Device ID: 0x4e50

Revision ID: 0x0000

Displays:

Display:

Resolution: 1280 x 1024

Depth: 32-bit Color

Core Image: Supported

Main Display: Yes

Mirror: Off

Online: Yes

Quartz Extreme: Supported

 

Or should it be in AGP Bus????

 

This is the specs from lspci -vv

 0000:00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 03)
Subsystem: IBM: Unknown device 0529
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable)
Capabilities: [e4] #09 [4104]
Capabilities: [a0] AGP version 2.0
	Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
	Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x1

0000:00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 96
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00003000-00003fff
Memory behind bridge: c0100000-c01fffff
Prefetchable memory behind bridge: e0000000-e7ffffff
Expansion ROM at 00003000 [disabled] [size=4K]
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

Item	Value	
Name	ATI MOBILITY RADEON 9600 Series	
PNP Device ID	PCI\VEN_1002&DEV_4E50&SUBSYS_05501014&REV_00\4&1BFA44D4&0&0008	
Adapter Type	ATI MOBILITY RADEON 9600/9700 Series AGP (0x4E50), ATI Technologies Inc. compatible	
Adapter Description	ATI MOBILITY RADEON 9600 Series	
Adapter RAM	64.00 MB (67,108,864 bytes)	
Installed Drivers	ati2dvag.dll	
Driver Version	6.14.10.6546	
INF File	oem43.inf (ati2mtag_M10 section)	
Color Planes	1	
Color Table Entries	4294967296	
Resolution	1400 x 1050 x 60 hertz	
Bits/Pixel	32	
Memory Address	0xE0000000-0xE7FFFFFF	
I/O Port	0x00003000-0x00003FFF	
Memory Address	0xC0100000-0xC01FFFFF	
IRQ Channel	IRQ 11	
I/O Port	0x000003B0-0x000003BB	
I/O Port	0x000003C0-0x000003DF	
Memory Address	0xA0000-0xBFFFF

 

Audio is working on off...

0000:00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
Subsystem: IBM: Unknown device 0537
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at 1c00
Region 1: I/O ports at 18c0 [size=64]
Region 2: Memory at c0000c00 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at c0000800 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
	Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
	Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Item	Value	
Name	SoundMAX Integrated Digital Audio	
Manufacturer	Analog Devices, Inc.	
Status	OK	
PNP Device ID	PCI\VEN_8086&DEV_24C5&SUBSYS_05371014&REV_01\3&61AAA01&0&FD	
I/O Port	0x00001C00-0x00001CFF	
I/O Port	0x000018C0-0x000018FF	
Memory Address	0xC0000C00-0xC0000DFF	
Memory Address	0xC0000800-0xC00008FF	
IRQ Channel	IRQ 11	
Driver	c:\windows\system32\drivers\smwdm.sys (5.12.01.5160, 260.63 KB (266,880 bytes), 29/11/1979 23:59)	

Name	Bluetooth Audio Device	
Manufacturer	WIDCOMM	
Status	OK	
PNP Device ID	ROOT\MEDIA\0000

 

 

Ideas?