hambone Posted March 31, 2007 Share Posted March 31, 2007 I can't seem to figure out how to use Natit. I installed version 0.2, the kernel seems to spew out a few messages about loading Natit during boot, however, no QI/CE/extended desktop. I see a lot of people talking about fiddling with various kexts. GeForce 6600 256MB AGP, I believe the card is manufactured by MSI. Right now I see the same thing on both monitors. Monitors are both flat panels with the old school VGA type connector, if that's important. I would appreciate it if someone could point me in the right direction. It sounds like people are making this card work and I'm just not "getting" it. Link to comment https://www.insanelymac.com/forum/topic/47083-nvidia-6600-agp-prentend-im-stupid/ Share on other sites More sharing options...
Elemenopee Posted April 14, 2007 Share Posted April 14, 2007 Bump. I need help too cause i was gonna install natit but i don'y know which one to install. Also, before i tried to install MacVidia drivers and Titan drivers but my screen diden't recive any signal after the grey apple screen when i rebooted. My card is an AGP XFX nvidia 6600 256MB dual dvi tv(i'm only using one monitor Link to comment https://www.insanelymac.com/forum/topic/47083-nvidia-6600-agp-prentend-im-stupid/#findComment-346974 Share on other sites More sharing options...
hibert Posted April 15, 2007 Share Posted April 15, 2007 I have the same problem with my NVidia 6600 agp 256mb .... I had try to install with Neo Installer and manuel by install natit.kext , but my screen diden't recive any signal after the grey apple screen when i rebooted , too ^^ SO PLZ CRACKS IN THIS FORUM OR MTV OR WHATEVER POST A METHODE THAT´S WORK ! sry for my bad english Wusst nicht mehr weiter ... Link to comment https://www.insanelymac.com/forum/topic/47083-nvidia-6600-agp-prentend-im-stupid/#findComment-347515 Share on other sites More sharing options...
U.C. Posted April 15, 2007 Share Posted April 15, 2007 Try the other display port. Also make sure the Device ID's are also present in NVDAResman.kext, NVDANV40HAL.kext and Geforce.kext. Try Natit 0.02 Dual. Also my 6600 AGP works with QE/CI as soon as I install 10.4.8 JaS. Alas I have other problems, click here Link to comment https://www.insanelymac.com/forum/topic/47083-nvidia-6600-agp-prentend-im-stupid/#findComment-347548 Share on other sites More sharing options...
Dominik G Posted September 25, 2010 Share Posted September 25, 2010 I have tried natit, nvdarwin, nvkush, nvdual 0.2 and no drivers, also using the agp kext. All work, but i am limited to 1024x768 on a 1600x1200 monitor (unless specified as a boot string) and rendering video is approx a frame every 2 seconds. I have tried adding EFI strings in OSx86Tools and EFI Studio, but at this stage on reboot my display sleeps after the Apple Boot screen. I have also tried switching my monitor to the dvi port via an adaptor. I got this card because my on-board graphics card is an Intel 865GME, for which I used the GMA900 drivers (limited to 1024x768) and the site says people have got this (NV GF6600) working... I've tried everything research has suggested and my head is starting to hurt... I (as I am sure the rest of us with this issue) would appreciate some info from someone that has it working... I am using iPC 10.5.6 PPF 6. Intel ICHx chipset. Graphics card is AGP not PCIe, if this makes a difference. Link to comment https://www.insanelymac.com/forum/topic/47083-nvidia-6600-agp-prentend-im-stupid/#findComment-1554229 Share on other sites More sharing options...
Recommended Posts