Jump to content
bgrau

Transition Chameleon to Clover - Asus P8H67-M LE

3 posts in this topic

Recommended Posts

Same as I started thread for High Sierra -

I am looking to get Clover to boot Yosemite on Asus P8H67-M LE

 

High Sierra (& Mojave) on Asus P8H67-M LE with Clover -

I was given the solution by Cyberdevs, so credits go to him - I am posting the full EFI ESP Clover folder together with the Clover 5103 installation pkg

https://www.dropbox.com/s/i39q5qz00etsl4w/ESP.zip?dl=0

https://www.dropbox.com/s/l75h9hdr4nxf9qa/Clover_v2.5k_r5103.pkg.zip?dl=0

 

It does not work for versions lower than High Sierra.

I wished to get Clover to work for Asus P8H67-M LE on Yosemite & Sierra,

if anyone has a working Clover for Yosemite for Asus P8H67M-LE, I would be grateful.

 

I will also share Chameleon (Enoch r2902 version) which works for Yosemite, Sierra here:

https://www.dropbox.com/s/c19d7wcay88sw52/Chameleon.zip?dl=0

though be warned that it can fail to boot & you need several attempts to get it booting, after that when in, it's rock solid...

 

RFC - what I don't really figure out is how the heck can the Clover bootloader load High Sierra & Mojave but not Yosemite, El Capitan & Sierra?

 

Also what am I missing of the transition from Chameleon to Clover, I can get Enoch r2902, an offshoot of Chameleon to load Yosemite & Sierra, but

what eludes me is how to get Yosemite & Sierra loaded with Clover instead on Asus P8H67-M LE...

 

Well I gave all my files, if a genius can find out what can make Clover load Yosemite (is what I am after because of USB 3.0) - I will be much obliged...
 

NB - submitted here https://www.insanelymac.com/forum/topic/295549-clover-config/?page=3&tab=comments&_fromLogin=1

but I wanted to get extra exposure on the Yosemite thread.

Edited by bgrau
Share this post

Personal recommendation honestly is to look into OpenCore - that can boot 10.4-11.0 with kext injection just fine - and I've gotten 10.7-10.11 to run on a core 2 system.

Though, no matter what bootloader you use, you should double check which versions kexts support - Yosemite I don't think is that old so I don't think compatibility will be to much of an issue.

"Does not load" is pretty vague - what is breaking?

Share this post

5 hours ago, 1Revenger1 said:

Personal recommendation honestly is to look into OpenCore - that can boot 10.4-11.0 with kext injection just fine - and I've gotten 10.7-10.11 to run on a core 2 system.

Though, no matter what bootloader you use, you should double check which versions kexts support - Yosemite I don't think is that old so I don't think compatibility will be to much of an issue.

"Does not load" is pretty vague - what is breaking?

It stays stuck after Got Boot Device...

When I try to boot to root terminal, the keyboard does not work...

The only reason I want clover is maybe for predictability & USB 3.0, as Enoch works but I have to try several runs before it holds, when I am in, I can leave it several days without any problem, it also has USB 3.0 working. USB 3.0 is lost after Yosemite with the USB 3.0 Renesens controller chip.

Share this post

×