Jump to content

Can't Shutdown and Boot time problem?

telepati

By telepati,
in OSx86 10.12 (Sierra)

 Share
13 posts in this topic

Recommended Posts

telepati
telepati
Posted
Posted

I have two problems. One of them I can't shutdown computer when I try to shutdown computer restart itself in a second. But when I try again this time its shutdown without any problem. But always shutdown in second attempt. 

 

I tried fix_shutdown and halt enabler on clover configurator but it doesn't help. I also tried ErP enabled on BIOS it doesn't help either.

 

Second problem is my boot time and shutdown time is to late. Boot time almost 1 minute shutdown 50 minutes. 

 

I attached my ioreg, Run me and Clover Folder without themes. 

 

Could someone look at these please? What is my problem what cause these?

 

Archive.zip

  • Like 1
MaLd0n
MaLd0n
Posted
Posted

-Update Clover

https://sourceforge.net/projects/cloverefiboot/files/Installer/Clover_v2.4k_r4049.zip/download

with these options

MaLd0n 2017-04-11 às 13.00.17.png

-Replace Folder

CLOVER.zip

Dont use kexts in L/E or S/L/E, if u have, remove, use only in Clover/Kexts/Other

-Generate new SSDT for PM, u use a old version

ssdtPRGen.command.zip

-send me ioreg after reboot

IORegistryExplorer 3.app.zip

 

BTW, for me the best is a fresh install and follow instructions, i dont know about ur previous installation, i think is TobyMacthumbsdown_anim.gif

  • Like 1
telepati
telepati
Posted
  • Author
Posted

-Update Clover

https://sourceforge.net/projects/cloverefiboot/files/Installer/Clover_v2.4k_r4049.zip/download

with these options

attachicon.gifMaLd0n 2017-04-11 às 13.00.17.png

-Replace Folder

attachicon.gifCLOVER.zip

Dont use kexts in L/E or S/L/E, if u have, remove, use only in Clover/Kexts/Other

-Generate new SSDT for PM, u use a old version

attachicon.gifssdtPRGen.command.zip

-send me ioreg after reboot

attachicon.gifIORegistryExplorer 3.app.zip

 

BTW, for me the best is a fresh install and follow instructions, i dont know about ur previous installation, i think is TobyMacattachicon.gifthumbsdown_anim.gif

 

Replaced all files. Attached new ioreg.

Murat’s Mac.zip

  • Like 1
telepati
telepati
Posted
  • Author
Posted

is fine now?

Ioreg is ok.

 

This is the new SSDT results is that normal?

Last login: Wed Apr 12 18:21:59 on console
Murats-Mac:~ muratozgul$ sudo -s
Password:
bash-3.2# chown -R 0:0 ~/Desktop/AppleIntelInfo.kext
bash-3.2# chmod -R 755 ~/Desktop/AppleIntelInfo.kext
bash-3.2# kextload ~/Desktop/AppleIntelInfo.kext
bash-3.2# cat /tmp/AppleIntelInfo.dat
AppleIntelInfo.kext v2.3 Copyright © 2012-2017 Pike R. Alpha. All rights reserved.
enableHWP................................: 0

Settings:
------------------------------------------
logMSRs..................................: 1
logIGPU..................................: 1
logCStates...............................: 1
logIPGStyle..............................: 1
InitialTSC...............................: 0xf1b51cb48d (25 MHz)
MWAIT C-States...........................: 1319200

Processor Brandstring....................: Intel(R) Core(TM) i7-6700K CPU @ 4.00GHz

Processor Signature..................... : 0x506E3
------------------------------------------
 - Family............................... : 6
 - Stepping............................. : 3
 - Model................................ : 0x5E (94)

Model Specific Registers (MSRs)
------------------------------------------

MSR_CORE_THREAD_COUNT............(0x35)  : 0xFFFFFF80B511A700
------------------------------------------
 - Core Count........................... : 4
 - Thread Count......................... : 8

MSR_PLATFORM_INFO................(0xCE)  : 0x80838F1012800
------------------------------------------
 - Maximum Non-Turbo Ratio.............. : 0x28 (4000 MHz)
 - Ratio Limit for Turbo Mode........... : 1 (programmable)
 - TDP Limit for Turbo Mode............. : 1 (programmable)
 - Low Power Mode Support............... : 0 (LMP not supported)
 - Number of ConfigTDP Levels........... : 0 (only base TDP level available)
 - Maximum Efficiency Ratio............. : 8
 - Minimum Operating Ratio.............. : 8

MSR_PMG_CST_CONFIG_CONTROL.......(0xE2)  : 0x0
------------------------------------------
 - I/O MWAIT Redirection Enable......... : 0 (not enabled)
 - CFG Lock............................. : 0 (MSR not locked)
 - C3 State Auto Demotion............... : 0 (disabled/unsupported)
 - C1 State Auto Demotion............... : 0 (disabled/unsupported)
 - C3 State Undemotion.................. : 0 (disabled/unsupported)
 - C1 State Undemotion.................. : 0 (disabled/unsupported)
 - Package C-State Auto Demotion........ : 0 (disabled/unsupported)
 - Package C-State Undemotion........... : 0 (disabled/unsupported)

MSR_PMG_IO_CAPTURE_BASE..........(0xE4)  : 0x0
 - C-state Range........................ : 0 (C-States not included, I/O MWAIT redirection not enabled)

IA32_MPERF.......................(0xE7)  : 0x3B43915959
IA32_APERF.......................(0xE8)  : 0x37D67D1787

MSR_FLEX_RATIO...................(0x194) : 0xE0000

MSR_IA32_PERF_STATUS.............(0x198) : 0x2C2400002A00
------------------------------------------
 - Current Performance State Value...... : 0x2A00 (4200 MHz)

MSR_IA32_PERF_CONTROL............(0x199) : 0x2A00
------------------------------------------
 - Target performance State Value....... : 0x2A00 (4200 MHz)
 - Intel Dynamic Acceleration........... : 0 (IDA engaged)

IA32_CLOCK_MODULATION............(0x19A) : 0x0

IA32_THERM_INTERRUPT.............(0x19B) : 0x10
------------------------------------------
 - High-Temperature Interrupt Enable.... : 0 (disabled)
 - Low-Temperature Interrupt Enable..... : 0 (disabled)
 - PROCHOT# Interrupt Enable............ : 0 (disabled)
 - FORCEPR# Interrupt Enable............ : 0 (disabled)
 - Critical Temperature Interrupt Enable : 1 (enabled)
 - Threshold #1 Value................... : 0
 - Threshold #1 Interrupt Enable........ : 0 (disabled)
 - Threshold #2 Value................... : 0
 - Threshold #2 Interrupt Enable........ : 0 (disabled)
 - Power Limit Notification Enable...... : 0 (disabled)

IA32_THERM_STATUS................(0x19C) : 0x884D0000
------------------------------------------
 - Thermal Status....................... : 0
 - Thermal Log.......................... : 0
 - PROCHOT # or FORCEPR# event.......... : 0
 - PROCHOT # or FORCEPR# log............ : 0
 - Critical Temperature Status.......... : 0
 - Critical Temperature log............. : 0
 - Thermal Threshold #1 Status.......... : 0
 - Thermal Threshold #1 log............. : 0
 - Thermal Threshold #2 Status.......... : 0
 - Thermal Threshold #2 log............. : 0
 - Power Limitation Status.............. : 0
 - Power Limitation log................. : 0
 - Current Limit Status................. : 0
 - Current Limit log.................... : 0
 - Cross Domain Limit Status............ : 0
 - Cross Domain Limit log............... : 0
 - Digital Readout...................... : 77
 - Resolution in Degrees Celsius........ : 1
 - Reading Valid........................ : 1 (valid)

MSR_THERM2_CTL...................(0x19D) : 0x0

IA32_MISC_ENABLES................(0x1A0) : 0x850089
------------------------------------------
 - Fast-Strings......................... : 1 (enabled)
 - FOPCODE compatibility mode Enable.... : 0
 - Automatic Thermal Control Circuit.... : 1 (enabled)
 - Split-lock Disable................... : 0
 - Performance Monitoring............... : 1 (available)
 - Bus Lock On Cache Line Splits Disable : 0
 - Hardware prefetch Disable............ : 0
 - Processor Event Based Sampling....... : 0 (PEBS supported)
 - GV1/2 legacy Enable.................. : 0
 - Enhanced Intel SpeedStep Technology.. : 1 (enabled)
 - MONITOR FSM.......................... : 1 (MONITOR/MWAIT supported)
 - Adjacent sector prefetch Disable..... : 0
 - CFG Lock............................. : 0 (MSR not locked)
 - xTPR Message Disable................. : 1 (disabled)

MSR_TEMPERATURE_TARGET...........(0x1A2) : 0x64140D
------------------------------------------
 - Turbo Attenuation Units.............. : 13 (122.1 micro-Seconds)
 - Temperature Target................... : 100
 - TCC Activation Offset................ : 0

MSR_MISC_PWR_MGMT................(0x1AA) : 0x401CC1
------------------------------------------
 - EIST Hardware Coordination........... : 1 (hardware coordination disabled)
 - Energy/Performance Bias support...... : 1
 - Energy/Performance Bias.............. : 0 (disabled/MSR not visible to software)
 - Thermal Interrupt Coordination Enable : 1 (thermal interrupt routed to all cores)

MSR_TURBO_RATIO_LIMIT............(0x1AD) : 0x2A2A2A2A
------------------------------------------
 - Maximum Ratio Limit for C01.......... : 2A (4200 MHz) 
 - Maximum Ratio Limit for C02.......... : 2A (4200 MHz) 
 - Maximum Ratio Limit for C03.......... : 2A (4200 MHz) 
 - Maximum Ratio Limit for C04.......... : 2A (4200 MHz) 

IA32_ENERGY_PERF_BIAS............(0x1B0) : 0x1
------------------------------------------
 - Power Policy Preference...............: 1 (highest performance)

MSR_POWER_CTL....................(0x1FC) : 0x3C005F
------------------------------------------
 - Bi-Directional Processor Hot..........: 1 (enabled)
 - C1E Enable............................: 1 (enabled)

MSR_RAPL_POWER_UNIT..............(0x606) : 0xA0E03
------------------------------------------
 - Power Units.......................... : 3 (1/8 Watt)
 - Energy Status Units.................. : 14 (61 micro-Joules)
 - Time Units .......................... : 10 (976.6 micro-Seconds)

MSR_PKG_POWER_LIMIT..............(0x610) : 0x42FFFF001BFFFF
------------------------------------------
 - Package Power Limit #1............... : 4095 Watt
 - Enable Power Limit #1................ : 1 (enabled)
 - Package Clamping Limitation #1....... : 1 (allow going below OS-requested P/T state during Time Window for Power Limit #1)
 - Time Window for Power Limit #1....... : 13 (20480 milli-Seconds)
 - Package Power Limit #2............... : 4095 Watt
 - Enable Power Limit #2................ : 1 (enabled)
 - Package Clamping Limitation #2....... : 0 (disabled)
 - Time Window for Power Limit #2....... : 33 (10 milli-Seconds)
 - Lock................................. : 0 (MSR not locked)

MSR_PKG_ENERGY_STATUS............(0x611) : 0x2F6218E
------------------------------------------
 - Total Energy Consumed................ : 3032 Joules (Watt = Joules / seconds)

MSR_PP1_POWER_LIMIT..............(0x640) : 0x0

MSR_PP1_ENERGY_STATUS............(0x641) : 0x5BF6A
------------------------------------------
 - Total Energy Consumed................ : 22 Joules (Watt = Joules / seconds)

MSR_PP1_POLICY...................(0x642) : 0x18
------------------------------------------
 - Priority Level....................... : 24

MSR_PKGC6_IRTL...................(0x60b) : 0x0
MSR_PKGC7_IRTL...................(0x60c) : 0x0
MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x0
MSR_PKG_C6_RESIDENCY.............(0x3f9) : 0x0
MSR_PKG_C7_RESIDENCY.............(0x3fa) : 0x0

MSR_PLATFORM_ENERGY_COUNTER......(0x64D) : 0x0 (not supported by hardware/BIOS)

MSR_PPERF........................(0x64E) : 0x35174F2035
------------------------------------------
 - Hardware workload scalability........ : 228024328245

MSR_CORE_PERF_LIMIT_REASONS......(0x64F) : 0x0

IA32_TSC_DEADLINE................(0x6E0) : 0xF1BF130C86

CPU Ratio Info:
------------------------------------------
Base Clock Frequency (BLCK)............. : 100 MHz
Maximum Efficiency Ratio/Frequency.......:  8 ( 800 MHz)
Maximum non-Turbo Ratio/Frequency........: 40 (4000 MHz)
Maximum Turbo Ratio/Frequency............: 42 (4200 MHz)

IGPU Info:
------------------------------------------
IGPU Current Frequency...................:    0 MHz
IGPU Minimum Frequency...................:  350 MHz
IGPU Maximum Non-Turbo Frequency.........:  350 MHz
IGPU Maximum Turbo Frequency.............: 1150 MHz
IGPU Maximum limit.......................: 1150 MHz

P-State ratio * 100 = Frequency in MHz
------------------------------------------
CPU P-States [ 38 (40) 42 ] iGPU P-States [ ]
CPU C6-Cores [ 0 1 5 6 ]
CPU P-States [ 32 38 40 (42) ] iGPU P-States [ ]
CPU C6-Cores [ 0 1 2 3 5 6 7 ]
CPU P-States [ 29 32 38 (40) 42 ] iGPU P-States [ ]
CPU C6-Cores [ 0 1 2 3 4 5 6 7 ]
CPU P-States [ (8) 27 29 32 38 40 42 ] iGPU P-States [ ]
CPU P-States [ 8 18 27 29 32 38 (40) 42 ] iGPU P-States [ ]
CPU P-States [ (8) 18 22 27 29 32 38 40 42 ] iGPU P-States [ ]
CPU P-States [ (8) 18 22 27 29 31 32 38 40 42 ] iGPU P-States [ ]
CPU P-States [ (8) 18 22 23 27 29 31 32 38 40 42 ] iGPU P-States [ ]
bash-3.2#
  • Like 1
telepati
telepati
Posted
  • Author
Posted

use last version

attachicon.gifAppleIntelInfo.kext.zip

 

Here is the result with the new version. is it look OK?

Last login: Wed Apr 12 22:31:14 on console
Murats-Mac:~ muratozgul$ sudo -s
Password:
bash-3.2# chown -R 0:0 ~/Desktop/AppleIntelInfo.kext
bash-3.2# chmod -R 755 ~/Desktop/AppleIntelInfo.kext
bash-3.2# kextload ~/Desktop/AppleIntelInfo.kext
bash-3.2# cat /tmp/AppleIntelInfo.dat
AppleIntelInfo.kext v2.5 Copyright © 2012-2017 Pike R. Alpha. All rights reserved.
enableHWP................................: 0

Settings:
------------------------------------------
logMSRs..................................: 1
logIGPU..................................: 1
logCStates...............................: 1
logIPGStyle..............................: 1
InitialTSC...............................: 0x146475504bbe (560 MHz)
MWAIT C-States...........................: 1319200

Processor Brandstring....................: Intel(R) Core(TM) i7-6700K CPU @ 4.00GHz

Processor Signature..................... : 0x506E3
------------------------------------------
 - Family............................... : 6
 - Stepping............................. : 3
 - Model................................ : 0x5E (94)

Model Specific Registers (MSRs)
------------------------------------------

MSR_CORE_THREAD_COUNT............(0x35)  : 0xFFFFFF80A7EFC000
------------------------------------------
 - Core Count........................... : 4
 - Thread Count......................... : 8

MSR_PLATFORM_INFO................(0xCE)  : 0x80838F1012800
------------------------------------------
 - Maximum Non-Turbo Ratio.............. : 0x28 (4000 MHz)
 - Ratio Limit for Turbo Mode........... : 1 (programmable)
 - TDP Limit for Turbo Mode............. : 1 (programmable)
 - Low Power Mode Support............... : 0 (LMP not supported)
 - Number of ConfigTDP Levels........... : 0 (only base TDP level available)
 - Maximum Efficiency Ratio............. : 8
 - Minimum Operating Ratio.............. : 8

MSR_PMG_CST_CONFIG_CONTROL.......(0xE2)  : 0x0
------------------------------------------
 - I/O MWAIT Redirection Enable......... : 0 (not enabled)
 - CFG Lock............................. : 0 (MSR not locked)
 - C3 State Auto Demotion............... : 0 (disabled/unsupported)
 - C1 State Auto Demotion............... : 0 (disabled/unsupported)
 - C3 State Undemotion.................. : 0 (disabled/unsupported)
 - C1 State Undemotion.................. : 0 (disabled/unsupported)
 - Package C-State Auto Demotion........ : 0 (disabled/unsupported)
 - Package C-State Undemotion........... : 0 (disabled/unsupported)

MSR_PMG_IO_CAPTURE_BASE..........(0xE4)  : 0x0
 - C-state Range........................ : 0 (C-States not included, I/O MWAIT redirection not enabled)

IA32_MPERF.......................(0xE7)  : 0x98500D7C7F
IA32_APERF.......................(0xE8)  : 0x83F180F180

MSR_FLEX_RATIO...................(0x194) : 0xE0000

MSR_IA32_PERF_STATUS.............(0x198) : 0x2B3A00002A00
------------------------------------------
 - Current Performance State Value...... : 0x2A00 (4200 MHz)

MSR_IA32_PERF_CONTROL............(0x199) : 0x2A00
------------------------------------------
 - Target performance State Value....... : 0x2A00 (4200 MHz)
 - Intel Dynamic Acceleration........... : 0 (IDA engaged)

IA32_CLOCK_MODULATION............(0x19A) : 0x0

IA32_THERM_INTERRUPT.............(0x19B) : 0x10
------------------------------------------
 - High-Temperature Interrupt Enable.... : 0 (disabled)
 - Low-Temperature Interrupt Enable..... : 0 (disabled)
 - PROCHOT# Interrupt Enable............ : 0 (disabled)
 - FORCEPR# Interrupt Enable............ : 0 (disabled)
 - Critical Temperature Interrupt Enable : 1 (enabled)
 - Threshold #1 Value................... : 0
 - Threshold #1 Interrupt Enable........ : 0 (disabled)
 - Threshold #2 Value................... : 0
 - Threshold #2 Interrupt Enable........ : 0 (disabled)
 - Power Limit Notification Enable...... : 0 (disabled)

IA32_THERM_STATUS................(0x19C) : 0x88460000
------------------------------------------
 - Thermal Status....................... : 0
 - Thermal Log.......................... : 0
 - PROCHOT # or FORCEPR# event.......... : 0
 - PROCHOT # or FORCEPR# log............ : 0
 - Critical Temperature Status.......... : 0
 - Critical Temperature log............. : 0
 - Thermal Threshold #1 Status.......... : 0
 - Thermal Threshold #1 log............. : 0
 - Thermal Threshold #2 Status.......... : 0
 - Thermal Threshold #2 log............. : 0
 - Power Limitation Status.............. : 0
 - Power Limitation log................. : 0
 - Current Limit Status................. : 0
 - Current Limit log.................... : 0
 - Cross Domain Limit Status............ : 0
 - Cross Domain Limit log............... : 0
 - Digital Readout...................... : 70
 - Resolution in Degrees Celsius........ : 1
 - Reading Valid........................ : 1 (valid)

MSR_THERM2_CTL...................(0x19D) : 0x0

IA32_MISC_ENABLES................(0x1A0) : 0x850089
------------------------------------------
 - Fast-Strings......................... : 1 (enabled)
 - FOPCODE compatibility mode Enable.... : 0
 - Automatic Thermal Control Circuit.... : 1 (enabled)
 - Split-lock Disable................... : 0
 - Performance Monitoring............... : 1 (available)
 - Bus Lock On Cache Line Splits Disable : 0
 - Hardware prefetch Disable............ : 0
 - Processor Event Based Sampling....... : 0 (PEBS supported)
 - GV1/2 legacy Enable.................. : 0
 - Enhanced Intel SpeedStep Technology.. : 1 (enabled)
 - MONITOR FSM.......................... : 1 (MONITOR/MWAIT supported)
 - Adjacent sector prefetch Disable..... : 0
 - CFG Lock............................. : 0 (MSR not locked)
 - xTPR Message Disable................. : 1 (disabled)

MSR_TEMPERATURE_TARGET...........(0x1A2) : 0x64140D
------------------------------------------
 - Turbo Attenuation Units.............. : 13 (122.1 micro-Seconds)
 - Temperature Target................... : 100
 - TCC Activation Offset................ : 0

MSR_MISC_PWR_MGMT................(0x1AA) : 0x401CC1
------------------------------------------
 - EIST Hardware Coordination........... : 1 (hardware coordination disabled)
 - Energy/Performance Bias support...... : 1
 - Energy/Performance Bias.............. : 0 (disabled/MSR not visible to software)
 - Thermal Interrupt Coordination Enable : 1 (thermal interrupt routed to all cores)

MSR_TURBO_RATIO_LIMIT............(0x1AD) : 0x2A2A2A2A
------------------------------------------
 - Maximum Ratio Limit for C01.......... : 2A (4200 MHz) 
 - Maximum Ratio Limit for C02.......... : 2A (4200 MHz) 
 - Maximum Ratio Limit for C03.......... : 2A (4200 MHz) 
 - Maximum Ratio Limit for C04.......... : 2A (4200 MHz) 

IA32_ENERGY_PERF_BIAS............(0x1B0) : 0x1
------------------------------------------
 - Power Policy Preference...............: 1 (highest performance)

MSR_POWER_CTL....................(0x1FC) : 0x3C005F
------------------------------------------
 - Bi-Directional Processor Hot..........: 1 (enabled)
 - C1E Enable............................: 1 (enabled)

MSR_RAPL_POWER_UNIT..............(0x606) : 0xA0E03
------------------------------------------
 - Power Units.......................... : 3 (1/8 Watt)
 - Energy Status Units.................. : 14 (61 micro-Joules)
 - Time Units .......................... : 10 (976.6 micro-Seconds)

MSR_PKG_POWER_LIMIT..............(0x610) : 0x42FFFF001BFFFF
------------------------------------------
 - Package Power Limit #1............... : 4095 Watt
 - Enable Power Limit #1................ : 1 (enabled)
 - Package Clamping Limitation #1....... : 1 (allow going below OS-requested P/T state during Time Window for Power Limit #1)
 - Time Window for Power Limit #1....... : 13 (20480 milli-Seconds)
 - Package Power Limit #2............... : 4095 Watt
 - Enable Power Limit #2................ : 1 (enabled)
 - Package Clamping Limitation #2....... : 0 (disabled)
 - Time Window for Power Limit #2....... : 33 (10 milli-Seconds)
 - Lock................................. : 0 (MSR not locked)

MSR_PKG_ENERGY_STATUS............(0x611) : 0x107DC04D
------------------------------------------
 - Total Energy Consumed................ : 16887 Joules (Watt = Joules / seconds)

MSR_PP1_POWER_LIMIT..............(0x640) : 0x0

MSR_PP1_ENERGY_STATUS............(0x641) : 0x3622B
------------------------------------------
 - Total Energy Consumed................ : 13 Joules (Watt = Joules / seconds)

MSR_PP1_POLICY...................(0x642) : 0x18
------------------------------------------
 - Priority Level....................... : 24

MSR_CONFIG_TDP_NOMINAL...........(0x648) : 0x28
MSR_CONFIG_TDP_LEVEL1............(0x649) : 0x0
MSR_CONFIG_TDP_LEVEL2............(0x64a) : 0x0
MSR_CONFIG_TDP_CONTROL...........(0x64b) : 0x80000000
MSR_TURBO_ACTIVATION_RATIO.......(0x64c) : 0x0
MSR_PKGC3_IRTL...................(0x60a) : 0x0
MSR_PKGC6_IRTL...................(0x60b) : 0x0
MSR_PKGC7_IRTL...................(0x60c) : 0x0
MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x0
MSR_PKG_C3_RESIDENCY.............(0x3f8) : 0x0
MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x0
MSR_PKG_C6_RESIDENCY.............(0x3f9) : 0x0
MSR_PKG_C7_RESIDENCY.............(0x3fa) : 0x0
MSR_PKG_C8_RESIDENCY............(0x630) : 0x0
MSR_PKG_C9_RESIDENCY............(0x631) : 0x0
MSR_PKG_C10_RESIDENCY...........(0x632) : 0x0
MSR_PKG_C8_LATENCY..............(0x633) : 0x0
MSR_PKG_C9_LATENCY..............(0x634) : 0x0
MSR_PKG_C10_LATENCY.............(0x635) : 0x0

MSR_PLATFORM_ENERGY_COUNTER......(0x64D) : 0x0 (not supported by hardware/BIOS)

MSR_PPERF........................(0x64E) : 0x7C31CD12DA
------------------------------------------
 - Hardware workload scalability........ : 533411467994

MSR_CORE_PERF_LIMIT_REASONS......(0x64F) : 0x0
HDC Supported

IA32_PKG_HDC_CTL.................(0xDB0) : 0x0

IA32_PM_CTL1.....................(0xDB1) : 0x1
------------------------------------------
HDC Allow Block..................(0xDB1) : 1 (HDC blocked)

IA32_THREAD_STALL................(0xDB2) : 0x0

MSR_PKG_HDC_CONFIG...............(0x652) : 0x2
------------------------------------------
Pkg Cx Monitor ..................(0x652) : 2 (count package C3 and deeper)
MSR_CORE_HDC_RESIDENCY...........(0x653) : 0x0

MSR_PKG_HDC_SHALLOW_RESIDENCY....(0x655) : 0x0

MSR_PKG_HDC_DEEP_RESIDENCY.......(0x656) : 0x0

IA32_TSC_DEADLINE................(0x6E0) : 0x1464811CB403
(HWP Supported but not (yet) enabled)

CPU Ratio Info:
------------------------------------------
Base Clock Frequency (BLCK)............. : 100 MHz
Maximum Efficiency Ratio/Frequency.......:  8 ( 800 MHz)
Maximum non-Turbo Ratio/Frequency........: 40 (4000 MHz)
Maximum Turbo Ratio/Frequency............: 42 (4200 MHz)

IGPU Info:
------------------------------------------
IGPU Current Frequency...................:    0 MHz
IGPU Minimum Frequency...................:  350 MHz
IGPU Maximum Non-Turbo Frequency.........:  350 MHz
IGPU Maximum Turbo Frequency.............: 1150 MHz
IGPU Maximum limit.......................: 1150 MHz

P-State ratio * 100 = Frequency in MHz
------------------------------------------
CPU P-States [ 34 (40) 42 ] iGPU P-States [ ]
CPU C6-Cores [ 0 2 7 ]
CPU P-States [ (8) 30 34 40 42 ] iGPU P-States [ ]
CPU C6-Cores [ 0 1 2 4 5 6 7 ]
CPU P-States [ 8 30 34 39 40 (42) ] iGPU P-States [ (21) ]
CPU C6-Cores [ 0 1 2 3 4 5 6 7 ]
CPU P-States [ (8) 30 31 34 39 40 42 ] iGPU P-States [ 21 ]
CPU P-States [ 8 30 31 34 37 39 (40) 42 ] iGPU P-States [ (21) ]
CPU P-States [ (8) 27 30 31 34 37 39 40 42 ] iGPU P-States [ 21 ]
CPU P-States [ (8) 27 28 30 31 34 37 39 40 42 ] iGPU P-States [ 21 ]
CPU P-States [ 8 27 28 30 31 33 34 37 39 40 (42) ] iGPU P-States [ 21 ]
CPU P-States [ (8) 26 27 28 30 31 33 34 37 39 40 42 ] iGPU P-States [ 21 ]
bash-3.2#
  • Like 1
telepati
telepati
Posted
  • Author
Posted

Man, take a test.

remove SSDT and add in config.plist Generate P and C States

attachicon.gifMaLd0n 2017-04-12 às 18.11.51.png

After reboot send new log with AppleIntelInfo.kext

 

Removed SSDT activate PState an CState, Here is the result;

Last login: Thu Apr 13 16:31:37 on console
Murats-Mac:~ muratozgul$ sudo -s
Password:
bash-3.2# chown -R 0:0 ~/Desktop/AppleIntelInfo.kext
bash-3.2# chmod -R 755 ~/Desktop/AppleIntelInfo.kext
bash-3.2# kextload ~/Desktop/AppleIntelInfo.kext
bash-3.2# cat /tmp/AppleIntelInfo.dat
AppleIntelInfo.kext v2.5 Copyright © 2012-2017 Pike R. Alpha. All rights reserved.
enableHWP................................: 0

Settings:
------------------------------------------
logMSRs..................................: 1
logIGPU..................................: 1
logCStates...............................: 1
logIPGStyle..............................: 1
InitialTSC...............................: 0xe5bb02c6cf (24 MHz)
MWAIT C-States...........................: 1319200

Processor Brandstring....................: Intel(R) Core(TM) i7-6700K CPU @ 4.00GHz

Processor Signature..................... : 0x506E3
------------------------------------------
 - Family............................... : 6
 - Stepping............................. : 3
 - Model................................ : 0x5E (94)

Model Specific Registers (MSRs)
------------------------------------------

MSR_CORE_THREAD_COUNT............(0x35)  : 0xFFFFFF809EDCD600
------------------------------------------
 - Core Count........................... : 4
 - Thread Count......................... : 8

MSR_PLATFORM_INFO................(0xCE)  : 0x80838F1012800
------------------------------------------
 - Maximum Non-Turbo Ratio.............. : 0x28 (4000 MHz)
 - Ratio Limit for Turbo Mode........... : 1 (programmable)
 - TDP Limit for Turbo Mode............. : 1 (programmable)
 - Low Power Mode Support............... : 0 (LMP not supported)
 - Number of ConfigTDP Levels........... : 0 (only base TDP level available)
 - Maximum Efficiency Ratio............. : 8
 - Minimum Operating Ratio.............. : 8

MSR_PMG_CST_CONFIG_CONTROL.......(0xE2)  : 0x0
------------------------------------------
 - I/O MWAIT Redirection Enable......... : 0 (not enabled)
 - CFG Lock............................. : 0 (MSR not locked)
 - C3 State Auto Demotion............... : 0 (disabled/unsupported)
 - C1 State Auto Demotion............... : 0 (disabled/unsupported)
 - C3 State Undemotion.................. : 0 (disabled/unsupported)
 - C1 State Undemotion.................. : 0 (disabled/unsupported)
 - Package C-State Auto Demotion........ : 0 (disabled/unsupported)
 - Package C-State Undemotion........... : 0 (disabled/unsupported)

MSR_PMG_IO_CAPTURE_BASE..........(0xE4)  : 0x0
 - C-state Range........................ : 0 (C-States not included, I/O MWAIT redirection not enabled)

IA32_MPERF.......................(0xE7)  : 0x6F8DE619D3
IA32_APERF.......................(0xE8)  : 0x6D620238E5

MSR_FLEX_RATIO...................(0x194) : 0xE0000

MSR_IA32_PERF_STATUS.............(0x198) : 0x2B2F00002A00
------------------------------------------
 - Current Performance State Value...... : 0x2A00 (4200 MHz)

MSR_IA32_PERF_CONTROL............(0x199) : 0x2A00
------------------------------------------
 - Target performance State Value....... : 0x2A00 (4200 MHz)
 - Intel Dynamic Acceleration........... : 0 (IDA engaged)

IA32_CLOCK_MODULATION............(0x19A) : 0x0

IA32_THERM_INTERRUPT.............(0x19B) : 0x10
------------------------------------------
 - High-Temperature Interrupt Enable.... : 0 (disabled)
 - Low-Temperature Interrupt Enable..... : 0 (disabled)
 - PROCHOT# Interrupt Enable............ : 0 (disabled)
 - FORCEPR# Interrupt Enable............ : 0 (disabled)
 - Critical Temperature Interrupt Enable : 1 (enabled)
 - Threshold #1 Value................... : 0
 - Threshold #1 Interrupt Enable........ : 0 (disabled)
 - Threshold #2 Value................... : 0
 - Threshold #2 Interrupt Enable........ : 0 (disabled)
 - Power Limit Notification Enable...... : 0 (disabled)

IA32_THERM_STATUS................(0x19C) : 0x88460000
------------------------------------------
 - Thermal Status....................... : 0
 - Thermal Log.......................... : 0
 - PROCHOT # or FORCEPR# event.......... : 0
 - PROCHOT # or FORCEPR# log............ : 0
 - Critical Temperature Status.......... : 0
 - Critical Temperature log............. : 0
 - Thermal Threshold #1 Status.......... : 0
 - Thermal Threshold #1 log............. : 0
 - Thermal Threshold #2 Status.......... : 0
 - Thermal Threshold #2 log............. : 0
 - Power Limitation Status.............. : 0
 - Power Limitation log................. : 0
 - Current Limit Status................. : 0
 - Current Limit log.................... : 0
 - Cross Domain Limit Status............ : 0
 - Cross Domain Limit log............... : 0
 - Digital Readout...................... : 70
 - Resolution in Degrees Celsius........ : 1
 - Reading Valid........................ : 1 (valid)

MSR_THERM2_CTL...................(0x19D) : 0x0

IA32_MISC_ENABLES................(0x1A0) : 0x850089
------------------------------------------
 - Fast-Strings......................... : 1 (enabled)
 - FOPCODE compatibility mode Enable.... : 0
 - Automatic Thermal Control Circuit.... : 1 (enabled)
 - Split-lock Disable................... : 0
 - Performance Monitoring............... : 1 (available)
 - Bus Lock On Cache Line Splits Disable : 0
 - Hardware prefetch Disable............ : 0
 - Processor Event Based Sampling....... : 0 (PEBS supported)
 - GV1/2 legacy Enable.................. : 0
 - Enhanced Intel SpeedStep Technology.. : 1 (enabled)
 - MONITOR FSM.......................... : 1 (MONITOR/MWAIT supported)
 - Adjacent sector prefetch Disable..... : 0
 - CFG Lock............................. : 0 (MSR not locked)
 - xTPR Message Disable................. : 1 (disabled)

MSR_TEMPERATURE_TARGET...........(0x1A2) : 0x64140D
------------------------------------------
 - Turbo Attenuation Units.............. : 13 (122.1 micro-Seconds)
 - Temperature Target................... : 100
 - TCC Activation Offset................ : 0

MSR_MISC_PWR_MGMT................(0x1AA) : 0x401CC1
------------------------------------------
 - EIST Hardware Coordination........... : 1 (hardware coordination disabled)
 - Energy/Performance Bias support...... : 1
 - Energy/Performance Bias.............. : 0 (disabled/MSR not visible to software)
 - Thermal Interrupt Coordination Enable : 1 (thermal interrupt routed to all cores)

MSR_TURBO_RATIO_LIMIT............(0x1AD) : 0x2A2A2A2A
------------------------------------------
 - Maximum Ratio Limit for C01.......... : 2A (4200 MHz) 
 - Maximum Ratio Limit for C02.......... : 2A (4200 MHz) 
 - Maximum Ratio Limit for C03.......... : 2A (4200 MHz) 
 - Maximum Ratio Limit for C04.......... : 2A (4200 MHz) 

IA32_ENERGY_PERF_BIAS............(0x1B0) : 0x1
------------------------------------------
 - Power Policy Preference...............: 1 (highest performance)

MSR_POWER_CTL....................(0x1FC) : 0x3C005F
------------------------------------------
 - Bi-Directional Processor Hot..........: 1 (enabled)
 - C1E Enable............................: 1 (enabled)

MSR_RAPL_POWER_UNIT..............(0x606) : 0xA0E03
------------------------------------------
 - Power Units.......................... : 3 (1/8 Watt)
 - Energy Status Units.................. : 14 (61 micro-Joules)
 - Time Units .......................... : 10 (976.6 micro-Seconds)

MSR_PKG_POWER_LIMIT..............(0x610) : 0x42FFFF001BFFFF
------------------------------------------
 - Package Power Limit #1............... : 4095 Watt
 - Enable Power Limit #1................ : 1 (enabled)
 - Package Clamping Limitation #1....... : 1 (allow going below OS-requested P/T state during Time Window for Power Limit #1)
 - Time Window for Power Limit #1....... : 13 (20480 milli-Seconds)
 - Package Power Limit #2............... : 4095 Watt
 - Enable Power Limit #2................ : 1 (enabled)
 - Package Clamping Limitation #2....... : 0 (disabled)
 - Time Window for Power Limit #2....... : 33 (10 milli-Seconds)
 - Lock................................. : 0 (MSR not locked)

MSR_PKG_ENERGY_STATUS............(0x611) : 0x39B88EC
------------------------------------------
 - Total Energy Consumed................ : 3694 Joules (Watt = Joules / seconds)

MSR_PP1_POWER_LIMIT..............(0x640) : 0x0

MSR_PP1_ENERGY_STATUS............(0x641) : 0x3BC3C
------------------------------------------
 - Total Energy Consumed................ : 14 Joules (Watt = Joules / seconds)

MSR_PP1_POLICY...................(0x642) : 0x18
------------------------------------------
 - Priority Level....................... : 24

MSR_CONFIG_TDP_NOMINAL...........(0x648) : 0x28
MSR_CONFIG_TDP_LEVEL1............(0x649) : 0x0
MSR_CONFIG_TDP_LEVEL2............(0x64a) : 0x0
MSR_CONFIG_TDP_CONTROL...........(0x64b) : 0x80000000
MSR_TURBO_ACTIVATION_RATIO.......(0x64c) : 0x0
MSR_PKGC3_IRTL...................(0x60a) : 0x0
MSR_PKGC6_IRTL...................(0x60b) : 0x0
MSR_PKGC7_IRTL...................(0x60c) : 0x0
MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x0
MSR_PKG_C3_RESIDENCY.............(0x3f8) : 0x0
MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x0
MSR_PKG_C6_RESIDENCY.............(0x3f9) : 0x0
MSR_PKG_C7_RESIDENCY.............(0x3fa) : 0x0
MSR_PKG_C8_RESIDENCY............(0x630) : 0x0
MSR_PKG_C9_RESIDENCY............(0x631) : 0x0
MSR_PKG_C10_RESIDENCY...........(0x632) : 0x0
MSR_PKG_C8_LATENCY..............(0x633) : 0x0
MSR_PKG_C9_LATENCY..............(0x634) : 0x0
MSR_PKG_C10_LATENCY.............(0x635) : 0x0

MSR_PLATFORM_ENERGY_COUNTER......(0x64D) : 0x0 (not supported by hardware/BIOS)

MSR_PPERF........................(0x64E) : 0x6A5DA54BC0
------------------------------------------
 - Hardware workload scalability........ : 456837647296

MSR_CORE_PERF_LIMIT_REASONS......(0x64F) : 0x0
HDC Supported

IA32_PKG_HDC_CTL.................(0xDB0) : 0x0

IA32_PM_CTL1.....................(0xDB1) : 0x1
------------------------------------------
HDC Allow Block..................(0xDB1) : 1 (HDC blocked)

IA32_THREAD_STALL................(0xDB2) : 0x0

MSR_PKG_HDC_CONFIG...............(0x652) : 0x2
------------------------------------------
Pkg Cx Monitor ..................(0x652) : 2 (count package C3 and deeper)
MSR_CORE_HDC_RESIDENCY...........(0x653) : 0x0

MSR_PKG_HDC_SHALLOW_RESIDENCY....(0x655) : 0x0

MSR_PKG_HDC_DEEP_RESIDENCY.......(0x656) : 0x0

IA32_TSC_DEADLINE................(0x6E0) : 0xE5C4BA7071
(HWP Supported but not (yet) enabled)

CPU Ratio Info:
------------------------------------------
Base Clock Frequency (BLCK)............. : 100 MHz
Maximum Efficiency Ratio/Frequency.......:  8 ( 800 MHz)
Maximum non-Turbo Ratio/Frequency........: 40 (4000 MHz)
Maximum Turbo Ratio/Frequency............: 42 (4200 MHz)

IGPU Info:
------------------------------------------
IGPU Current Frequency...................: 1050 MHz
IGPU Minimum Frequency...................:  350 MHz
IGPU Maximum Non-Turbo Frequency.........:  350 MHz
IGPU Maximum Turbo Frequency.............: 1150 MHz
IGPU Maximum limit.......................: 1150 MHz

P-State ratio * 100 = Frequency in MHz
------------------------------------------
CPU P-States [ (8) 39 42 ] iGPU P-States [ ]
CPU C6-Cores [ 0 1 3 4 5 7 ]
CPU P-States [ 8 21 39 (40) 42 ] iGPU P-States [ ]
CPU C6-Cores [ 0 1 2 3 4 5 7 ]
CPU P-States [ 8 21 31 39 40 (42) ] iGPU P-States [ ]
CPU C6-Cores [ 0 1 2 3 4 5 6 7 ]
CPU P-States [ (8) 21 27 31 39 40 42 ] iGPU P-States [ ]
CPU P-States [ (8) 20 21 27 31 39 40 42 ] iGPU P-States [ ]
CPU P-States [ (8) 20 21 27 29 31 39 40 42 ] iGPU P-States [ ]
CPU P-States [ (8) 20 21 27 29 31 33 39 40 42 ] iGPU P-States [ ]
CPU P-States [ (8) 20 21 27 29 31 33 35 39 40 42 ] iGPU P-States [ ]
CPU P-States [ 8 20 21 23 27 29 31 33 35 39 (40) 42 ] iGPU P-States [ ]
CPU P-States [ (8) 20 21 23 27 29 30 31 33 35 39 40 42 ] iGPU P-States [ ]
CPU P-States [ (8) 20 21 23 27 28 29 30 31 33 35 39 40 42 ] iGPU P-States [ ]
CPU P-States [ 8 20 21 23 25 27 28 29 30 31 33 35 39 40 (42) ] iGPU P-States [ ] 

But you told me on post #4 create a new SSDT will I now use it anymore?

 Share
Go to topic listing
×
×
  • Create New...