Jump to content
17 posts in this topic

Recommended Posts

Hi guys,

 

i've started a thread also in the Italian section of the forum some days ago and i've done some step forward in my El Capiten Installing attempt.

 

This is my hardware spec:

- Motherboard: Asus Z10PE D8-WS

- CPU: 2 x Intel XEON E5-2650v3

- Graphics: nVidia GeForce GT 610 (temporary, only for installation, after i'll mount nVidia GTX 980 Ti)

 

I've finally arrived at the last boot line:

*** [IOBluetoothHCIController][SearchForTransportEventTimeOutHandler] -- Missing Bluetooth Controller Transport!
DSMOS has arrived.

but after that i've a reboot.  :(

 

I'm trying some boot option and flag (such Inject nVidia = Yes/No, GraphicsEnabler = Yes/No) but i can't boot the installer.

 

I've also another strange thing, when i boot with Safe Boot flag (-x), the boot stucks at [PCI Controller has start] line at the beginning of the boot (i've always write npci=0x2000 flag)

 

I'll be very proud if someone can help me going into the installer  :rolleyes:

 

Thank you very much!

Hi guys,

 

i've started a thread also in the Italian section of the forum some days ago and i've done some step forward in my El Capiten Installing attempt.

 

This is my hardware spec:

- Motherboard: Asus Z10PE D8-WS

- CPU: 2 x Intel XEON E5-2650v3

- Graphics: nVidia GeForce GT 610 (temporary, only for installation, after i'll mount nVidia GTX 980 Ti)

 

I've finally arrived at the last boot line:

*** [IOBluetoothHCIController][SearchForTransportEventTimeOutHandler] -- Missing Bluetooth Controller Transport!
DSMOS has arrived.

but after that i've a reboot.  :(

 

I'm trying some boot option and flag (such Inject nVidia = Yes/No, GraphicsEnabler = Yes/No) but i can't boot the installer.

 

I've also another strange thing, when i boot with Safe Boot flag (-x), the boot stucks at [PCI Controller has start] line at the beginning of the boot (i've always write npci=0x2000 flag)

 

I'll be very proud if someone can help me going into the installer  :rolleyes:

 

Thank you very much!

need FakeSMC.kext....your bootloader is?

Thanks for the answer.

 

I'm using Clover, but in the folder EFI/CLOVER/kext/ there's the FakeSMC.kext.

install another version to check it :thumbsup_anim:....also ..copy kext in S/L/E

And boot flag is :

-v npci=0x2000 rootless=0 kext dev mode=1

try

FakeSMC.kext.zip

Installed but nothing to do....it stucks at DSMOS has arrived

 

O.T. Gratz for the 1.000 posts  :thumbsup_anim:

post your config.plist.....

you use DSDT file?Your SMBIOS is?

Same fail, always stuck a DSMOS has arrived.

eject all stuff on pc,like sd card usb,hdd external

boot clean..only usb flash and hdd for os x

remove bluetooh kexts from S/L/E folder, keep a backup. post list of kexts in your EFI folder

 

Hanging at BluetoothControllerTransport usually has nothing to do with Bluetooth; it's usually caused by graphics failing to init, or loginwindow failing to load (due to FakeSMC not loading). Could be the former in this situtation, but I haven't seen it reboot after hanging.

You can try this EFI folder

I tried that file but i've a reboot loop on [PCI Controller begin] also adding the boot flag npci=0x2000...

 

Someone tell me that's impossible to install El Capitan on my hardware, because my chipset are not supported...it is correct?

It's impossible or is hard to install? The problem i have now (reboot on DSMOS has arrived) is only a graphics problem or is a generic problem?

I ask that because this is only my 2nd hackintosh....with the first was all correct, but now i'm trying to install for four days...

Edited by M4rc0k
×
×
  • Create New...