Jump to content
  • Announcements

    • Allan

      Forum Rules   04/13/2018

      Hello folks! As some things are being fixed, we'll keep you updated. Per hour the Forum Rules don't have a dedicated "Tab", so here is the place that we have our Rules back. New Users Lounge > [READ] - InsanelyMac Forum Rules - The InsanelyMac Staff Team. 
bberts

Intel Panther Point Usb 3.0

9 posts in this topic

Recommended Posts

Hi i' ve managed a new retail installation on a Fujitsu C710

I have get all to work at full with some fix now i can't enable only usb 3.0

i can see 2 Usb controller this one :

 

 

Bus USB 3.0 ad alta velocità:

 

Posizione controller host: USB integrata

Driver controller host: AppleUSBXHCI

ID dispositivo PCI: 0x7f8200001e31

ID revisione PCI: 0x7f8200000004

ID fornitore PCI: 0x7f8200008086

Numero bus: 0x14

 

and this one:

 

 

 

 

Bus USB ad alta velocità:

 

Posizione controller host: USB integrata

Driver controller host: AppleUSBEHCI

ID dispositivo PCI: 0x1e2d

ID revisione PCI: 0x0004

ID fornitore PCI: 0x8086

Numero bus: 0x1a

 

I now the frist is for 3.0 xhci also the second is for 2.0 ehci

 

i' ve try a lot of solutions PXHCD and add my id 0x1e31 in the info.plist of AppleUSBXHCI.kext

 

but nothing work...

 

If anyone know how make it on please help me THX.

 

 

i'm sorry for my bad english...

 

Alberto

post-655052-0-98991900-1357486566_thumb.png

Share this post


Link to post
Share on other sites

Do you have any USB options in bios ? I had the same problem but got USB working nativelly but enabling XHCI and disabling legacy USB. See if you have same options.

Share this post


Link to post
Share on other sites

Do you have any USB options in bios ? I had the same problem but got USB working nativelly but enabling XHCI and disabling legacy USB. See if you have same options.

 

Thanks i' ve try to set usb as XHCI but no disabling legacy mode now i wanna try it but you also use patched kext to enable it?

 

sorry for stupid question ' working nativelly '

Share this post


Link to post
Share on other sites

Maybe the problem is that u have both USB 2 and USB 3 in your system. In mine i have only USB 3 and when i put in bios USB legacy = enabled my device is detected as 2.0 whereas putting XHCI = enabled gives me all devices working as 3.0.

Share this post


Link to post
Share on other sites

Yes i' ve 2 usb controller one usb 2.0

(

0x1e2d)

and one usb 3.0

(

0x1e31

)

and if i set XHCI or Legacy in bios nothing change.

 

But u see XHCI controller in system profiler ? and this

0x1e31 is your id HW?

Share this post


Link to post
Share on other sites

At the End on my pc Fujitsu c710 if i DISABLING xHCI mode for USB in BIOS all my port work like 2.0 :weight_lift: (THX

and i don't see anyone usb3.0 in system profiler between if enable xHCI mode in BIOS i can see 2 hub 3.0 but it don't work

Share this post


Link to post
Share on other sites

Hi I have the same set up as you as far as USB goes. I have found that USB3.0 only works from boot. That is to say if I plugin in my USB3.0 external drive and then start my laptop I the have the external drive showing in finder. If I "hot plug" nothing happens. You might want to test this.

Share this post


Link to post
Share on other sites

For me if i enable xHCI my 4x3.0 usb don't work anyway plug in by start on or not also if i disable xhci mode in bios all my usb 10 6x2.0 4x3.0 ( my pc it's desktop ultrasmall series ) work as 2.0 in osx ML

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Recently Browsing   0 members

    No registered users viewing this page.

×