sidisido Posted December 16, 2011 Share Posted December 16, 2011 Hello, I am using RealtekRTL81xx.kext and the LAN works perfectly, if I have the LAN Cable plugged in on boot. If I replug the LAN Cable, it doesnt work any longer.. It says connected but has no IP. I don't know what LAN Card I have.. This information is nowhere. Regards Link to comment https://www.insanelymac.com/forum/topic/273580-realtekrtl81xxkext/ Share on other sites More sharing options...
LatinMcG Posted December 16, 2011 Share Posted December 16, 2011 motherboard model and rev might help. or lspci try lnx2mac driver Link to comment https://www.insanelymac.com/forum/topic/273580-realtekrtl81xxkext/#findComment-1779060 Share on other sites More sharing options...
sidisido Posted December 16, 2011 Author Share Posted December 16, 2011 motherboard model and rev might help. or lspci try lnx2mac driver I already have lnx2mac installed. I don't know the Mainboard Model at all.. Here is the fact sheet. http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02863970&tmp_task=prodinfoCategory&cc=de&dlc=de&lc=de&product=5112803 I found out, if i unload the kext and load it again, i can replug it, and it still works.. Regards Link to comment https://www.insanelymac.com/forum/topic/273580-realtekrtl81xxkext/#findComment-1779080 Share on other sites More sharing options...
LatinMcG Posted December 16, 2011 Share Posted December 16, 2011 http://uploaded.to/file/b7gy5i lspci likely its some dsdt issue Link to comment https://www.insanelymac.com/forum/topic/273580-realtekrtl81xxkext/#findComment-1779083 Share on other sites More sharing options...
sidisido Posted December 16, 2011 Author Share Posted December 16, 2011 http://uploaded.to/file/b7gy5i lspci likely its some dsdt issue Thanks, but I have never heard of this lpci.. I installed it, what should I do now ? Regards Link to comment https://www.insanelymac.com/forum/topic/273580-realtekrtl81xxkext/#findComment-1779084 Share on other sites More sharing options...
LatinMcG Posted December 17, 2011 Share Posted December 17, 2011 nice spam of lspci try -v -n so its not 20 miles/kilometers long. i see u have an hp laptop DV6-6115EG make sure its not loading usb3 driver PXHCD apparently some have issues with it and shutdown/ sleep. Link to comment https://www.insanelymac.com/forum/topic/273580-realtekrtl81xxkext/#findComment-1779272 Share on other sites More sharing options...
sidisido Posted December 17, 2011 Author Share Posted December 17, 2011 lspci -v -n: pcilib: 0000:07:00.0 64-bit device address ignored. pcilib: 0000:07:00.0 64-bit device address ignored. pcilib: 0000:00:02.0 64-bit device address ignored. pcilib: 0000:01:00.0 64-bit device address ignored. 00:00.0 0600: 8086:0104 (rev 09) Subsystem: 103c:3388 Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information <?> 00:01.0 0604: 8086:0101 (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00005000-00005fff Memory behind bridge: c6500000-c65fffff Prefetchable memory behind bridge: 0000000f10000000-0000000f1fffffff Capabilities: [88] Subsystem: 103c:3388 Capabilities: [80] Power Management version 3 Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Capabilities: [a0] Express Root Port (Slot+), MSI 00 Capabilities: [100] #8086 00:02.0 0300: 8086:0116 (rev 09) (prog-if 00 [VGA controller]) Subsystem: 103c:3388 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at c0000000 (64-bit, non-prefetchable) Memory at <ignored> (64-bit, prefetchable) I/O ports at 6000 Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Capabilities: [d0] Power Management version 2 Capabilities: [a4] PCIe advanced features <?> 00:16.0 0780: 8086:1c3a (rev 04) Subsystem: 103c:3388 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at c7504000 (64-bit, non-prefetchable) Capabilities: [50] Power Management version 3 Capabilities: [8c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+ 00:1a.0 0c03: 8086:1c2d (rev 05) (prog-if 20 [EHCI]) Subsystem: 103c:3388 Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at c750a000 (32-bit, non-prefetchable) Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCIe advanced features <?> 00:1b.0 0403: 8086:1c20 (rev 05) Subsystem: 103c:3388 Flags: bus master, fast devsel, latency 0, IRQ 22 Memory at c7500000 (64-bit, non-prefetchable) Capabilities: [50] Power Management version 2 Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] #8086 Capabilities: [1c2] #400 Capabilities: [010] Power Budgeting <?> Capabilities: [c75] #00 Capabilities: [100] <chain looped> 00:1c.0 0604: 8086:1c10 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 I/O behind bridge: 00004000-00004fff Prefetchable memory behind bridge: 0000000f30000000-0000000f300fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Capabilities: [90] Subsystem: 103c:3388 Capabilities: [a0] Power Management version 2 Capabilities: [100] #8086 00:1c.1 0604: 8086:1c12 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=0d, subordinate=0d, sec-latency=0 Memory behind bridge: c4500000-c45fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Capabilities: [90] Subsystem: 103c:3388 Capabilities: [a0] Power Management version 2 Capabilities: [100] #8086 00:1c.2 0604: 8086:1c14 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=13, subordinate=13, sec-latency=0 Memory behind bridge: c3500000-c35fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Capabilities: [90] Subsystem: 103c:3388 Capabilities: [a0] Power Management version 2 Capabilities: [100] #8086 00:1c.3 0604: 8086:1c16 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=19, subordinate=19, sec-latency=0 Memory behind bridge: c3400000-c34fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Capabilities: [90] Subsystem: 103c:3388 Capabilities: [a0] Power Management version 2 Capabilities: [100] #8086 00:1d.0 0c03: 8086:1c26 (rev 05) (prog-if 20 [EHCI]) Subsystem: 103c:3388 Flags: bus master, medium devsel, latency 0, IRQ 20 Memory at c7509000 (32-bit, non-prefetchable) Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCIe advanced features <?> 00:1f.0 0601: 8086:1c49 (rev 05) Subsystem: 103c:3388 Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information <?> 00:1f.2 0106: 8086:1c03 (rev 05) (prog-if 01 [AHCI 1.0]) Subsystem: 103c:3388 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19 I/O ports at 6088 I/O ports at 609c I/O ports at 6080 I/O ports at 6098 I/O ports at 6060 Memory at c7508000 (32-bit, non-prefetchable) Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Capabilities: [70] Power Management version 3 Capabilities: [a8] SATA HBA <?> Capabilities: [b0] PCIe advanced features <?> 00:1f.3 0c05: 8086:1c22 (rev 05) Subsystem: 103c:3388 Flags: medium devsel, IRQ 19 Memory at c7506000 (64-bit, non-prefetchable) I/O ports at 6040 01:00.0 0300: 1002:6740 (prog-if 00 [VGA controller]) Subsystem: 103c:3388 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at <ignored> (64-bit, prefetchable) Memory at c6500000 (64-bit, non-prefetchable) I/O ports at 5000 [disabled] Expansion ROM at fffe0000 [disabled] Capabilities: [50] Power Management version 3 Capabilities: [58] Express Legacy Endpoint, MSI 00 Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [100] #1002 07:00.0 0200: 10ec:8168 (rev 06) Subsystem: 103c:3388 Flags: bus master, fast devsel, latency 0, IRQ 16 I/O ports at 4000 Memory at <ignored> (64-bit, prefetchable) Memory at <ignored> (64-bit, prefetchable) Capabilities: [40] Power Management version 3 Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [70] Express Endpoint, MSI 01 Capabilities: [b0] MSI-X: Enable- Mask- TabSize=4 Capabilities: [d0] Vital Product Data <?> Capabilities: [100] #10ec 0d:00.0 0280: 8086:008b (rev 34) Subsystem: 8086:5315 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at c4500000 (64-bit, non-prefetchable) Capabilities: [c8] Power Management version 3 Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [e0] Express Endpoint, MSI 00 Capabilities: [100] #8086 Capabilities: [008] #34 13:00.0 ff00: 10ec:5209 (rev 01) Subsystem: 103c:3388 Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at c3500000 (32-bit, non-prefetchable) Expansion ROM at ffff0000 [disabled] Capabilities: [40] Power Management version 3 Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [70] Express Endpoint, MSI 00 Capabilities: [100] #10ec 19:00.0 0c03: 1033:0194 (rev 04) (prog-if 30) Subsystem: 103c:3388 Flags: bus master, fast devsel, latency 0, IRQ 19 Memory at c3400000 (64-bit, non-prefetchable) Capabilities: [50] Power Management version 3 Capabilities: [70] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable- Capabilities: [90] MSI-X: Enable- Mask- TabSize=8 Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] #1033 Link to comment https://www.insanelymac.com/forum/topic/273580-realtekrtl81xxkext/#findComment-1779308 Share on other sites More sharing options...
LatinMcG Posted December 17, 2011 Share Posted December 17, 2011 can u edit the first lspi post and make it short. 1: what version lnx2mac driver u have ? the v9? 2: have u searched for a dsdt thread for similar model series Laptop (DV6-611)? anyone have this or similar laptop runing ok ? 3: how did you install lion or snow ? we need dsdt and ioreg ioregistry explorer http://www.mediafire.com/?mlzwnwmmjj4 save the ioreg and zip (right click compress) dsdt.. get dsdt editor http://www.insanelym...pic=223205&st=0 extract dsdt and zip Link to comment https://www.insanelymac.com/forum/topic/273580-realtekrtl81xxkext/#findComment-1779311 Share on other sites More sharing options...
sidisido Posted December 17, 2011 Author Share Posted December 17, 2011 1. i have 0.0.90 2. i have this dsdt file (http://www.insanelymac.com/forum/index.php?showtopic=273065'>http://www.insanelymac.com/forum/index.php?showtopic=273065) 3. i installed lion with this DMG (http://www.insanelymac.com/forum/index.php?showtopic=273065) ioreg: http://localhostr.com/file/eeAp3JT/sidisido.ioreg.zip i extracted the dsdt , but where is it stored ? Regards Link to comment https://www.insanelymac.com/forum/topic/273580-realtekrtl81xxkext/#findComment-1779322 Share on other sites More sharing options...
LatinMcG Posted December 18, 2011 Share Posted December 18, 2011 My Modified kernel in / dsdt might be wrong due to ram size or bios version make a .dsl from both original yours and his dsdt and compare it with text wrangler u have to click save after extracting . it displays it. u can add to a text file and name it dsdt.dsl Link to comment https://www.insanelymac.com/forum/topic/273580-realtekrtl81xxkext/#findComment-1779358 Share on other sites More sharing options...
sidisido Posted December 18, 2011 Author Share Posted December 18, 2011 My Modified kernel in / dsdt might be wrong due to ram size or bios version make a .dsl from both original yours and his dsdt and compare it with text wrangler u have to click save after extracting . it displays it. u can add to a text file and name it dsdt.dsl I use the DSDT from the thread, how do you mean, i should compare it ? i only have one http://localhostr.com/file/mKiva6F/dsdt.dsl.zip Link to comment https://www.insanelymac.com/forum/topic/273580-realtekrtl81xxkext/#findComment-1779410 Share on other sites More sharing options...
LatinMcG Posted December 18, 2011 Share Posted December 18, 2011 your original dsdt and the dsdt u dload. make them into .dsl then compare. you have to boot with no dsdt to get original. heres how to do it from linux http://linux-hybrid-graphics.blogspot.com Link to comment https://www.insanelymac.com/forum/topic/273580-realtekrtl81xxkext/#findComment-1779468 Share on other sites More sharing options...
Recommended Posts